Finite Element Analysis of the Influence of Balance Mode on Rolling Mill Universal Spindle Strength

2014 ◽  
Vol 548-549 ◽  
pp. 449-453 ◽  
Author(s):  
Zhi Qiang Guo ◽  
Ze Lu Xu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanical Model ◽  
Rolling Mill ◽  
Loading Condition ◽  
Equivalent Stress ◽  
Bending Moment ◽  
Element Model ◽  
Element Analysis ◽  
Universal Spindle

For the problem of balance bearing of universal spindle in rolling mill being prone to damage, the paper established mechanical model and finite element model of universal spindle. The paper has analyzed that the shear and bending moment in the middle of the shaft is the largest. The fillet near shoulder of balance bearing of the spindle is dangerous part. In order to reduce principal stress of universal spindle caused by moment, the paper improved balance mode of the spindle. The equilibrant was applied from in one place of shaft to put in two places. After optimizing, equivalent stress of the spindle is slight smaller than before under the same loading condition, which illustrates that the strength of the spindle is appropriately improved. Although the effect is not obvious, this has played a guiding role for the optimization of balance mode of universal spindle.

The Finite Element Analysis on the Compression Splicing Position of Strain Clamp in Guy Tower

2014 ◽  
Vol 680 ◽  
pp. 249-253
Author(s):  
Zhang Qi Wang ◽  
Jun Li ◽  
Wen Gang Yang ◽  
Yong Feng Cheng
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Finite Element Model ◽  
Equivalent Stress ◽  
Element Model ◽  
Element Analysis ◽  
Elastic Plastic ◽  
The Finite Element Analysis

Strain clamp is an important connection device in guy tower. If the quality of the compression splicing position is unsatisfied, strain clamp tends to be damaged which may lead to the final collapse of a guy tower as well as huge economic lost. In this paper, stress distribution on the compressible tube and guy cable is analyzed by FEM, and a large equivalent stress of guy cable is applied to the compression splicing position. During this process, a finite element model of strain clamp is established for guy cables at compression splicing position, problems of elastic-plastic and contracting are studied and the whole compressing process of compressible position is simulated. The guy cable cracks easily at the position of compressible tube’s port, the inner part of the compressible tube has a larger equivalent stress than outside.

Finite Element Analysis of Hydraulic Clipping Machine Shear Platform Dased on ANSYS

2014 ◽  
Vol 945-949 ◽  
pp. 190-193
Author(s):  
Hai Lin Wang ◽  
Yi Hua Sun ◽  
Ming Bo Li ◽  
Gao Lin ◽  
Yun Qi Feng ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Elastic Strain ◽  
Optimization Design ◽  
Equivalent Stress ◽  
Element Model ◽  
Element Analysis ◽  
Maximum Equivalent Stress

Q43Y-85D type crocodile hydraulic clipping machine was taken as research object to optimization design. A finite element model for clipping machine was built using shell unit as fundamental unit. ANSYS12.0 finite element method was used to analyze the deformation and stress distribution of the shear platform model of hydraulic clipping machine. The result showed that the maximum equivalent stress at the dangerous area was 368.162 MPa and the maximum elastic strain was 0.1814×10-2 mm. After the structural optimization design, it was found that the maximum equivalent stress decreased to 186.238 MPa which did not exceed the material’s yield limitation 215 MPa and the maximum elastic strain decreased to 0.919×10-3 mm which satisfied the requirement of stiffness.

Finite Element Analysis of Cold Expanding of Hollow Thin-Wall Tube

2011 ◽  
Vol 460-461 ◽  
pp. 44-47
Author(s):  
Wei Hua Kuang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Equivalent Stress ◽  
Element Model ◽  
Thin Wall ◽  
Forming Process ◽  
Element Analysis ◽  
Simulation Step ◽  
The Finite Element Analysis

The cold expanding diameter process was simulated by the software of DEFORM. The finite element model of tube and dies were built. The object position definition, the inter object setting, movement definition and simulation step were correctly set. The deformation, total velocity distribution and equivalent stress distribution were predicted. The numerical simulation results showed that the finite element analysis could exactly describe the plastic deformation and stress distribution during the forming process.

A Biomechanical and Finite Element Analysis of Femoral Neck Notching During Hip Resurfacing

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Edward T. Davis ◽  
Michael Olsen ◽  
Rad Zdero ◽  
Marcello Papini ◽  
James P. Waddell ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Femoral Neck ◽  
Finite Element Model ◽  
Proximal Femur ◽  
Equivalent Stress ◽  
Element Model ◽  
Hip Resurfacing ◽  
Stress And Strain ◽  
Element Analysis

Hip resurfacing is an alternative to total hip arthroplasty in which the femoral head surface is replaced with a metallic shell, thus preserving most of the proximal femoral bone stock. Accidental notching of the femoral neck during the procedure may predispose it to fracture. We examined the effect of neck notching on the strength of the proximal femur. Six composite femurs were prepared without a superior femoral neck notch, six were prepared in an inferiorly translated position to create a 2 mm notch, and six were prepared with a 5 mm notch. Six intact synthetic femurs were also tested. The samples were loaded to failure axially. A finite element model of a composite femur with increasing superior notch depths computed maximum equivalent stress and strain distributions. Experimental results showed that resurfaced synthetic femurs were significantly weaker than intact femurs (mean failure of 7034 N, p<0.001). The 2 mm notched group (mean failure of 4034 N) was significantly weaker than the un-notched group (mean failure of 5302 N, p=0.018). The 5 mm notched group (mean failure of 2808 N) was also significantly weaker than both the un-notched and the 2 mm notched groups (p<0.001, p=0.023, respectively). The finite element model showed the maximum equivalent strain in the superior reamed cancellous bone increasing with corresponding notch size. Fracture patterns inferred from equivalent stress distributions were consistent with those obtained from mechanical testing. A superior notch of 2 mm weakened the proximal femur by 24%, and a 5 mm notch weakened it by 47%. The finite element analysis substantiates this showing increasing stress and strain distributions within the prepared femoral neck with increasing notch depth.

Development of J-Integral Solutions for Semi-Elliptical Circumferential Cracked Pipes Subjected to Internal Pressure and Bending Moment

2015 ◽  
Author(s):  
Makoto Udagawa ◽  
Jinya Katsuyama ◽  
Yoshihito Yamaguchi ◽  
Yinsheng Li ◽  
Kunio Onizawa
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Loading Condition ◽  
Bending Moment ◽  
J Integral ◽  
Surface Cracks ◽  
Element Analysis ◽  
Elastic Plastic ◽  
Piping Systems ◽  
Integral Solutions

The J-integral solutions for cracked pipes are important in crack growth calculation and failure evaluation based on the elastic-plastic fracture mechanics. One of the most important crack types in structural integrity assessment for nuclear piping systems is circumferential semi-elliptical surface crack on the inside of the pipes. Although several J-integral solutions have been provided, no solutions were developed at both the deepest and the surface points of circumferential semi-elliptical surface cracks in pipes. In this study, with backgrounds described above, the J-integral solutions of circumferential semi-elliptical surface cracks on the inside of the pipe were developed by numerical finite element analyses. Three dimensional elastic-plastic analyses were performed considering different material properties, pipe sizes, crack dimensions and, especially, combined loading condition of internal pressure and bending moment which is a typical loading condition for nuclear piping systems. The J values at both the deepest and the surface points were extracted from finite element analysis results. Moreover, in order to benefit users in practical applications, a pair of convenient J-integral estimation equations were developed based on the calculated J values at the deepest and the surface points. Finally, the accuracy and applicability of the convenient equations were confirmed by comparing with the provided stress intensity factor solutions in elastic region and with finite element analysis results in elastic-plastic region.

Finite element analysis and structural design of axially uniform-loaded nut

2017 ◽  
Vol 52 (4) ◽  
pp. 215-225
Author(s):  
Zhao Chun-jiang ◽  
Liu Yong-feng ◽  
Zhang Fei-tao ◽  
Wang Zheng-yi ◽  
Gui Hai-lian
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Equivalent Stress ◽  
Peak Stress ◽  
Element Model ◽  
Working Process ◽  
Element Analysis ◽  
Finite Element Software ◽  
Heavy Equipment

Axially heavy-loaded screw pairs are widely used in rolling mill press systems and other heavy equipment. During the working process, the nut is pressed at both ends, which causes equivalent stress at the thread roots in a U-shaped distribution along the height. Thread roots at the ends tend to suffer fracture failure when the equivalent stress is too great. In this article, the finite element software ANSYS is used to establish a 3D model of screw pairs and analyse bearing characteristics. A new structure based on the results of finite element analysis, which improves U-shaped stress distribution, is proposed for the axially uniform-loaded nut, with a different strain–displacement relationship between the nut matrix and the thread teeth. Such a relationship can greatly reduce peak stress at the thread roots of the nut on both ends. Experiments are conducted on the nut using the electrometric method. Results are compared with the finite element results to directly verify the reliability of the finite element model of ordinary screw pairs and indirectly verify the reliability of the structural model of new screw pairs.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis and Optimization of Long-Span Gantry NC Machining Center Structure

2011 ◽  
Vol 346 ◽  
pp. 379-384
Author(s):  
Shu Bo Xu ◽  
Yang Xi ◽  
Cai Nian Jing ◽  
Ke Ke Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Method ◽  
Dynamic Performance ◽  
Plate Thickness ◽  
Element Model ◽  
Wall Structure ◽  
Characteristic Analysis ◽  
Element Analysis ◽  
Dynamic Performance Analysis

The use of finite element theory and modal analysis theory, the structure of the machine static and dynamic performance analysis and prediction using optimal design method for optimization, the new machine to improve job performance, improve processing accuracy, shorten the development cycle and enhance the competitiveness of products is very important. Selected for three-dimensional CAD modeling software-UG NX4.0 and finite element analysis software-ANSYS to set up the structure of the beam finite element model, and then post on the overall structure of the static and dynamic characteristic analysis, on the basis of optimized static and dynamic performance is more superior double wall structure of the beam. And by changing the wall thickness and the thickness of the inner wall, as well as the reinforcement plate thickness overall sensitivity analysis shows that changes in these three parameters on the dynamic characteristics of post impact. Application of topology optimization methods, determine the optimal structure of the beam ultimately.

Sign in / Sign up

Export Citation Format

Share Document