Effective Method of Repairing RC Beam Using Externally Bonded Steel Plate

2014 ◽  
Vol 567 ◽  
pp. 399-404 ◽  
Author(s):  
Md Ashraful Alam ◽  
Ali Sami Abdul Jabbar ◽  
Mohd Zamin Jumaat ◽  
Kamal Nasharuddin Mustapha
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Steel Plate ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Rc Beam ◽  
External Reinforcement ◽  
Externally Bonded ◽  
Damaged Beams

Repair of reinforced concrete beam with externally bonded steel plate or fibre reinforced polymer (FRP) laminate is becoming both environmentally and economically preferable rather than replacement of deficient beam. The well known advantages of external reinforcement over other methods include; low cost, ease of maintenance and the ability to strengthen part of the structure while it is still in use. The disadvantage of this method, however, is the premature debonding of the externally bonded strips which is brittle and undesired mode of failure. It is also known that debonding of the externally bonded steel plates prevents the reinforced concrete (RC) beam from reaching its full strengthening capacity. The aim of this study was to increase the scientific understanding on the behaviour of damaged reinforced concrete beams strengthened and/or retrofitted for shear using vertical steel plate fixed with adhesive and steel connectors to eliminate or delay debonding failure. Four reinforced concrete beam specimens were prepared to investigate the effects of connectors in preventing or delaying premature debonding of shear strips to restore the capacities of fully damaged beams. Three damaged beams have been repaired and strengthened with steel plates and loaded monotonically up to the maximum load capacities in order to define load–deflection relationship. It is concluded that the repairing of severely shear-damaged RC beams with steel plates by using steel and adhesive connectors can fully restore the original shear capacities of the beams.

Study on Impaired Reinforced Concrete Beams Strengthening with Externally Steel Frame

2013 ◽  
Vol 438-439 ◽  
pp. 477-481
Author(s):  
Feng Lan Li ◽  
Xiong Huai Yu ◽  
Cheng Chen ◽  
Song Chen
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Concrete Beam ◽  
Steel Plate ◽  
Reinforced Concrete Beam ◽  
Steel Frame ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Externally Bonded ◽  
Strengthening Method

A large impaired reinforced concrete beam with cracks was strengthened under self-weight action by the externally bonded steel frame composed with bottom steel plate and side hoop steel belts. The normal service loading behaviors of this beam were tested to verify the effectiveness of this strengthening method specified in current Chinese design code. Based on the analyses of test results, it can be concluded that: the deformation of flexural cross section of this beam fitted the assumption of plain cross section, the steel plate could effectively enhance the flexural stiffness and decrease the deflection of this beam, no new cracks appeared under the normal service loads, the cracks at bottom of this beam were more confined by the steel frame than those at web zone. Therefore, other measure should be taken to avoid the opening of web cracks.

scholarly journals The Effect of Steel Plate on the Deflection of Self Reinforced Concrete Beam with and Without Opening

2013 ◽  
Vol 6 (1) ◽  
pp. 36-49
Author(s):  
Ali Sabah AL-Amili
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Steel Plate ◽  
Failure Load ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Flexural Behavior ◽  
External Plate

In this work aims at studying the influence of steel plate on the deflection of self- compacted reinforced concrete beams was investigated experimentally in this study to know the flexural behavior of these beams. Eight simply supported reinforced concrete beam were tested under the action of two point loads .The deflections of the beams with and without plate are measured. The steel plates of thickness (3 mm) with dimensions ( 170 × 350 mm) were used. These plates were sticked on the concrete beams using epoxy. The steel plate inside the beam was sticked with and without epoxy (epoxy type EP), while the beams were taken with and without opening (10 mm diameter). The results show that the plate increased the capacity of the beam by increased the value of failure load. Hence, the beam with internal plate with epoxy increased the failure load by 34.2% than beam without plate , and 24.6% than beam with internal plate without epoxy , and 19.7% than beam with external plate with epoxy .

scholarly journals Behavior of Reinforced Concrete Beams with effect of Stiffened Plates

2019 ◽  
Vol 5 (12) ◽  
pp. 2569-2578 ◽  
Author(s):  
Ali Sabah Al Amli ◽  
Laith Shakir ◽  
Ali Abdulredha ◽  
Nadhir Al-Ansari
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Steel Plate ◽  
Concrete Beams ◽  
Reference Beam ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Maximum Increase ◽  
Thin Steel

This study presents experimental work including an investigation conducted on five simply supported reinforced concrete beams under pure torsion. First beam without strengthening as a control beam. The other four beams were strengthened externally by bolted thin steel plates. For this test the load was applied gradually. The torque was increased gradually up to failure of the beam.  The variables were the thickness and height of the steel plate that was externally connected to both sides of the rectangular reinforced concrete beam. The test results for the beams discussed are based on torque-twist behavior. The experimental results show that the attachment of thin steel plates by mechanical means to beams provides a considerable improvement in the torsional behavior of the reinforced concrete beams. Comparable to the reference beam, the maximum increase in the cracking and the ultimate torque of the composite beam was recorded for the reinforced concrete beam that strengthen by steel plate of (150) mm height, (2mm) thickness and (50mm) spacing between shear connectors (B1). The results revealed that the cracking torque, ultimate torque, global stiffness of beam and beam ductility for all composite beams increase with the increase of the plate's thickness, plate's height.

scholarly journals Experimental Study on the Flexural Behavior of over Reinforced Concrete Beams Bolted with Compression Steel Plate: Part I

2020 ◽  
Vol 10 (3) ◽  
pp. 822 ◽  
Author(s):  
Shatha Alasadi ◽  
Payam Shafigh ◽  
Zainah Ibrahim
Keyword(s):  
Reinforced Concrete ◽  
Failure Modes ◽  
Steel Plate ◽  
Concrete Beams ◽  
Peak Load ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Flexural Behavior ◽  
Flexural Stiffness

The purpose of this paper is to investigate the flexural behavior of over-reinforced concrete beam enhancement by bolted-compression steel plate (BCSP) with normal reinforced concrete beams under laboratory experimental condition. Three beams developed with steel plates were tested until they failed in compression compared with one beam without a steel plate. The thicknesses of the steel plates used were 6 mm, 10 mm, and 15 mm. The beams were simply supported and loaded monotonically with two-point loads. Load-deflection behaviors of the beams were observed, analyzed, and evaluated in terms of spall-off concrete loading, peak loading, displacement at mid-span, flexural stiffness (service and post-peak), and energy dissipation. The outcome of the experiment shows that the use of a steel plate can improve the failure modes of the beams and also increases the peak load and flexural stiffness. The steel development beams dissipated much higher energies with an increase in plate thicknesses than the conventional beam.

Laminated Composite Beam with Bonded CFRP Reinforcement Stress Performance Analysis

2012 ◽  
Vol 204-208 ◽  
pp. 3160-3163
Author(s):  
Yong Wei Wang ◽  
Yan Qin Guo ◽  
Hong Xia Li
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Concrete Beam ◽  
Laminated Composite ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Rc Beam ◽  
Essential Difference ◽  
Cfrp Composite ◽  
Laminated Layer

Based on the test of 7 reinforced concrete beam reinforcement test data comparison analysis shows that only the ordinary reinforced concrete beams with externally bonded CFRP, effectively improve the bearing capacity of members, but due to the lower tensile reserves and the upper compression reserve is relatively insufficient, make a component similar over-reinforced beam brittle failure, its ultimate bearing capacity was significantly lower than the upper part at the same time a laminated layer of the RC beam. Laminated paste CFRP composite reinforced RC beam damage characteristics and common reinforced concrete beam was no essential difference, but the laminated layer thickness reaches to a certain degree, the CFRP can also occur with sudden local cleavage fracture.

scholarly journals Damage Evaluation in Shear-Critical Reinforced Concrete Beam using Piezoelectric Transducers as Smart Aggregates

2015 ◽  
Vol 5 (1) ◽  
Author(s):  
Constantin E. Chalioris ◽  
Nikos A. Papadopoulos ◽  
Georgia M. Angeli ◽  
Chris G. Karayannis ◽  
Asterios A. Liolios ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Shear Failure ◽  
Reinforced Concrete Beam ◽  
Piezoelectric Transducers ◽  
Reinforced Concrete Beams ◽  
Structural Safety ◽  
Shear Span ◽  
Externally Bonded ◽  
Diagonal Crack

AbstractDamage detection at early cracking stages in shear-critical reinforced concrete beams, before further deterioration and their inevitable brittle shear failure is crucial for structural safety and integrity. The effectiveness of a structural health monitoring technique using the admittance measurements of piezoelectric transducers mounted on a reinforced concrete beam without shear reinforcement is experimentally investigated. Embedded “smart aggregate” transducers and externally bonded piezoelectric patches have been placed in arrays at both shear spans of the beam. Beam were tested till total shear failure and monitored at three different states; healthy, flexural cracking and diagonal cracking. Test results showed that transducers close to the critical diagonal crack provided sound and graduated discrepancies between the admittance responses at the healthy state and thedamage levels.Damage assessment using statistical indices calculated from the measurements of all transducers was also attempted. Rational changes of the index values were obtained with respect to the increase of the damage. Admittance responses and index values of the transducers located on the shear span where the critical diagonal crack formed provided cogent evidence of damage. On the contrary, negligible indication of damage was yielded by the responses of the transducers located on the other shear span, where no diagonal cracking occurred.

Numerical Simulation about Reinforced Concrete Beams Strengthened by Bolting Steel Plates

2012 ◽  
Vol 166-169 ◽  
pp. 1807-1810
Author(s):  
Xue Song Gao ◽  
Dong Hui Huo ◽  
Shao Hua Lv ◽  
Xu Zhao
Keyword(s):  
Reinforced Concrete ◽  
Steel Plate ◽  
Concrete Beams ◽  
Three Dimensional ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Anchor Bolt ◽  
Beam Surface ◽  
Strengthened Beam

This paper presents a three-dimensional nonlinear finite elemental analysis about the reinforcement concrete beams strengthened by bolting steel plate. The contact effects between the steel plate with reinforced concrete beam surface was simulated by developing the contact elements. The effect of strengthening is analyzed and the effects of the deformation and stress distribution of anchor bolt on the failure mode were investigated. It is declared that this strengthening method can obviously improve the capacity and stiffness of beam, and the flexural deformation of anchor bolt is key problem inducing the failure of strengthened beam. This template explains and demonstrates how to prepare your camera-ready paper for Trans Tech Publications. The best is to read these instructions and follow the outline of this text.

scholarly journals Toward Structural Health Monitoring of Civil Structures Based on Self-Sensing Concrete Nanocomposites: A Validation in a Reinforced-Concrete Beam

2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Diego L. Castañeda-Saldarriaga ◽  
Joham Alvarez-Montoya ◽  
Vladimir Martínez-Tejada ◽  
Julián Sierra-Pérez
Keyword(s):  
Reinforced Concrete ◽  
Damage Detection ◽  
Direct Current ◽  
Health Monitoring ◽  
Electrical Resistance ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Structural Member ◽  
Rc Beam ◽  
Electric Resistance

AbstractSelf-sensing concrete materials, also known as smart concretes, are emerging as a promising technological development for the construction industry, where novel materials with the capability of providing information about the structural integrity while operating as a structural material are required. Despite progress in the field, there are issues related to the integration of these composites in full-scale structural members that need to be addressed before broad practical implementations. This article reports the manufacturing and multipurpose experimental characterization of a cement-based matrix (CBM) composite with carbon nanotube (CNT) inclusions and its integration inside a representative structural member. Methodologies based on current–voltage (I–V) curves, direct current (DC), and biphasic direct current (BDC) were used to study and characterize the electric resistance of the CNT/CBM composite. Their self-sensing behavior was studied using a compression test, while electric resistance measures were taken. To evaluate the damage detection capability, a CNT/CBM parallelepiped was embedded into a reinforced-concrete beam (RC beam) and tested under three-point bending. Principal finding includes the validation of the material’s piezoresistivity behavior and its suitability to be used as strain sensor. Also, test results showed that manufactured composites exhibit an Ohmic response. The embedded CNT/CBM material exhibited a dominant linear proportionality between electrical resistance values, load magnitude, and strain changes into the RC beam. Finally, a change in the global stiffness (associated with a damage occurrence on the beam) was successfully self-sensed using the manufactured sensor by means of the variation in the electrical resistance. These results demonstrate the potential of CNT/CBM composites to be used in real-world structural health monitoring (SHM) applications for damage detection by identifying changes in stiffness of the monitored structural member.

scholarly journals Influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams

2018 ◽  
Vol 21 (13) ◽  
pp. 1977-1989 ◽  
Author(s):  
Tengfei Xu ◽  
Jiantao Huang ◽  
Arnaud Castel ◽  
Renda Zhao ◽  
Cheng Yang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Natural Frequencies ◽  
Concrete Beams ◽  
Dynamic Stiffness ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Reinforcing Bar ◽  
Sustained Loading ◽  
Inertia Model

In this article, experiments focusing at the influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams are reported. In these experiments, the bond between concrete and reinforcing bar was damaged using appreciate flexural loads. The static stiffness of cracked reinforced concrete beam was assessed using the measured load–deflection response under cycles of loading and unloading, and the dynamic stiffness was analyzed using the measured natural frequencies with and without sustained loading. Average moment of inertia model (Castel et al. model) for cracked reinforced beams by taking into account the respective effect of bending cracks (primary cracks) and the steel–concrete bond damage (interfacial microcracks) was adopted to calculate the static load–deflection response and the natural frequencies of the tested beams. The experimental results and the comparison between measured and calculated natural frequencies show that localized steel–concrete bond damage does not influence remarkably the dynamic stiffness and the natural frequencies both with and without sustained loading applied. Castel et al. model can be used to calculate the dynamic stiffness of cracked reinforced concrete beam by neglecting the effect of interfacial microcracks.

Prediction Scheme of Torsional Strength of Reinforced Concrete Beam

2012 ◽  
Vol 214 ◽  
pp. 306-310
Author(s):  
Han Chen Huang
Keyword(s):  
Genetic Algorithm ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Ann Model ◽  
Torsional Strength ◽  
Prediction Scheme ◽  
Optimal Network

This study proposes a artificial neural network with genetic algorithm (GA-ANN) for predicting the torsional strength of reinforced concrete beam. Genetic algorithm is used to the optimal network structure and parameters. A database of the torsional failure of reinforced concrete beams with a rectangular section subjected to pure torsion was obtained from existing literature for analysis. This study compare the predictions of the GA-ANN model with the ACI 318 code used for analyzing the torsional strength of reinforced concrete beam. The results show that the proposed model provides reasonable predictions of the ultimate torsional strength of reinforced concrete beams and offers superior torsion accuracy compared to that of the ACI 318-89 equation.

Sign in / Sign up

Export Citation Format

Share Document