Research on Cooling Control System of Flue Gas Based on Fuzzy Control

2014 ◽  
Vol 610 ◽  
pp. 497-500
Author(s):  
Ming Gang Zheng ◽  
Nan Wei

High-temperature flue gas in the factory has three features: high flow, strong corrosive and high temperature. It must be cooled to the rated temperature of different working conditions. There are nonlinear, time-varying issues and difficult to establish accurate mathematical model in the control of pump water quantity. We put PLC as the core to design the cooling control system which adjusts the pump water quantity by frequency changer based on fuzzy control theory.

2011 ◽  
Vol 383-390 ◽  
pp. 1262-1266
Author(s):  
Zhen Guo Jia

Designed a device with PLC and inverter for transformer cooling control system. The structure of fuzzy controller is built with PLC. By calculating and testing, fuzzy and fuzzy control rules are established. Practical computing for the PLC to control the output lookup table is given. Using this technique, transformer cooling system energy consumption will be reduced, transformer’s coolers life will be extended and transformer cooling system automation level will be increased.


Author(s):  
Kuniyoshi Takamatsu ◽  
Kazuhiro Sawa

The High-Temperature Engineering Test Reactor (HTTR) is the first High-Temperature Gas-cooled Reactor (HTGR) with a thermal power of 30 MW and a maximum reactor outlet coolant temperature of 950 °C; it was built at the Oarai Research and Development Center of JAEA. At present, test studies are being conducted using the HTTR to improve HTGR technologies in collaboration with domestic industries that also contribute to foreign projects for the acceleration of HTGR development worldwide. To improve HTGR technologies, advanced analysis techniques are currently under development using data obtained with the HTTR, which include reactor kinetics, thermal hydraulics, safety evaluation, and fuel performance evaluation data (including the behavior of fission products). In this study, a three gas circulator trip test and a vessel cooling system (VCS) stop test were performed as a loss of forced cooling (LOFC) test to demonstrate the inherent safety features of HTGR. The VCS stop test involved stopping the VCS located outside the reactor pressure vessel to remove the residual heat of the reactor core as soon as the three gas circulators are tripped. All three gas circulators were tripped at 9, 24 and 30 MW. The primary coolant flow rate was reduced from the rated 45 t/h to 0 t/h. Control rods (CRs) were not inserted into the core and the reactor power control system was not operational. In fact, the three gas circulator tripping test at 9 MW has already been performed in a previous study. However, the results cannot be disclosed to the public because of a confidentiality agreement. Therefore, we cannot refer to the difference between the analytical and test results. We determined that the reactor power immediately decreases to the decay heat level owing to the negative reactivity feedback effect of the core, although the reactor shutdown system was not operational. Moreover, the temperature distribution in the core changes slowly because of the high heat capacity due to the large amount of core graphite. Core dynamics analysis of the LOFC test for the HTTR was performed. The relationship among the reactivities (namely, Doppler, moderator temperature, and xenon reactivities) affecting recriticality time and reactor peak power level as well as total reactivity was addressed. Furthermore, the analytical results for a reactor transient of hundred hours are presented. Based on the results, emergency operating procedures can be developed for the case of a loss of coolant accident in HTGR when the CRs are not inserted into the core and the reactor power control system is not operational. The analytical results will be used in the design and construction of the Kazakhstan High-Temperature Reactor and the realization of commercial Very High-Temperature Reactor systems.


Author(s):  
Omar Farhan Al-Hardanee ◽  
İlyas Çankaya ◽  
Abdulmuttalib A. Muhsen ◽  
Huseyin Canbolat

The core of a typical hydroelectric power plant is the turbine. Vibration and overheating in a turbine occur when water flows through it, and with increased vibration and high temperature, it will cause the turbine blade to break. In this study, the control and monitoring system is designed to predict and avoid any error before it occurs. This process is achieved by measuring vibration and temperature using sensors and sending signals through the Arduino to the graphical user interfaces (GUI), the system compares the signals taken from the sensors with the permissible limits, and when the permissible limits are exceeded, the processor takes appropriate measures to open and close the turbine gates, where the data is displayed in matrix laboratory graphical user interfaces (MATLAB’s GUI) screen. In this way, monitoring is done, and the appropriate action are taken to avoid mistakes.


Robotica ◽  
1986 ◽  
Vol 4 (2) ◽  
pp. 101-105 ◽  
Author(s):  
Guy Jumarie

SUMMARYFor a manipulator which works in a given fixed environment, like in manufacturing plants for instance, the control system may be designed in a fixed definite way. But when the characteristics of this environment is subject to variations, e.g. change in the mass of the object to be moved, it is necessary to endow the manipulator with some versatility which allows it to adapt itself to the new working conditions. The purpose of the paper is to show that the use of links with varying inertia is a possible way to achieve this flexibility.


Author(s):  
P.P.K. Smith

Grains of pigeonite, a calcium-poor silicate mineral of the pyroxene group, from the Whin Sill dolerite have been ion-thinned and examined by TEM. The pigeonite is strongly zoned chemically from the composition Wo8En64FS28 in the core to Wo13En34FS53 at the rim. Two phase transformations have occurred during the cooling of this pigeonite:- exsolution of augite, a more calcic pyroxene, and inversion of the pigeonite from the high- temperature C face-centred form to the low-temperature primitive form, with the formation of antiphase boundaries (APB's). Different sequences of these exsolution and inversion reactions, together with different nucleation mechanisms of the augite, have created three distinct microstructures depending on the position in the grain.In the core of the grains small platelets of augite about 0.02μm thick have farmed parallel to the (001) plane (Fig. 1). These are thought to have exsolved by homogeneous nucleation. Subsequently the inversion of the pigeonite has led to the creation of APB's.


Alloy Digest ◽  
1994 ◽  
Vol 43 (5) ◽  

Abstract URANUS 52N is a nitrogen-alloyed duplex stainless steel improved in stress-corrosion cracking resistance and with pitting and crevice corrosion resistance better than AISI Type 317L. Applications include handling phosphoric acid contaminated with chlorides and in flue gas desulfurization scrubbers. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-566. Producer or source: Creusot-Marrel.


Alloy Digest ◽  
2004 ◽  
Vol 53 (8) ◽  

Abstract AL 4565 alloy has a high level of austenitizers, which provides the microstructure with a high resistance to sigma formation during welding. The high nitrogen also gives the alloy superior strength among the austenitics. Applications include flue gas desulfurization and handling seawater. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance and corrosion resistance as well as heat treating and joining. Filing Code: SS-906. Producer or source: Allegheny Ludlum Corporation.


Sign in / Sign up

Export Citation Format

Share Document