Design and Development of Antennas Design and Testing System

2014 ◽  
Vol 610 ◽  
pp. 827-834
Author(s):  
Xiao Ying Ran ◽  
Zhen Yu
Keyword(s):  
Software Design ◽  
Impedance Measurement ◽  
Visual Basic ◽  
Measurement Procedure ◽  
Testing System ◽  
Simulation Design ◽  
Curricular Innovation ◽  
Experimental Teaching ◽  
Experiment Hardware ◽  
Design And Testing

Based on the antenna experiment hardware, an antennas design and testing system is achieved by use of Visual Basic and Flash software development tools. The paper introduces the antenna experiment hardware and antenna pattern and input impedance measurement methods, discusses the overall structure of the system and software design. Take the helical antenna as an example demonstrates the system application in antenna simulation, design, and measurement procedure. The application shows that the self-developed system with interactive, practical and realistic which has been applied to the curricular experimental teaching and extra-curricular innovation, and achieved good results.

A Prototype Monitoring System for Automotive CAN Bus Gauge

2013 ◽  
Vol 336-338 ◽  
pp. 1391-1395
Author(s):  
Yi Ming Lee ◽  
Fu-Yen Yeh ◽  
Shyue Bin Chang
Keyword(s):  
Monitoring System ◽  
Software Design ◽  
Communication Protocol ◽  
Can Bus ◽  
Testing System ◽  
Electronic Control ◽  
Log Files ◽  
Control Modules ◽  
Ethernet Technology

CAN bus communication has been used in a serial protocol for connecting electronic control modules together with its hardware and software design in automotive gauge application. The motivation is to develop a PC-based monitoring system for not only CAN frames received from or sent onto CAN bus, but also data recorded on log files consideration. This paper presents a prototype monitoring system on automotive CAN bus gauge for communication protocol in Ford Mustang. For the proposed CAN bus monitoring system, the designed architecture is discussed and verified into PC for surveillance performance. Furthermore the Ethernet technology adopted in the system makes it a more practical and convenient CAN bus testing system.

MCU Experimental Teaching System Based on Proteus

2014 ◽  
Vol 701-702 ◽  
pp. 1128-1131
Author(s):  
Wen Na Xu ◽  
Chun Wang
Keyword(s):  
Teaching Method ◽  
Present Situation ◽  
Teaching Experiment ◽  
Simulation System ◽  
Testing System ◽  
Welding Temperature ◽  
Teaching System ◽  
Experiment System ◽  
Experimental Teaching ◽  
The Cost

This paper put forward a viable scheme and demonstrate the feasibility of MCU experiment teaching system with PROTEUS according to analyze the present situation and the problems of MCU teaching experiment in colleges and universities. The simulation system was designed according to a case of testing system of welding temperature. The experiment results show that the experiment system can enrich the experiment teaching method, increase the interests of the students in learning, reduce the cost of experiment and improve the quality and efficiency of education.

UG Simulation Design of Electromagnetic Dryer

2013 ◽  
Vol 680 ◽  
pp. 398-401
Author(s):  
Zheng Shun Wang ◽  
Zhao Hui Zhen
Keyword(s):  
Software Design ◽  
Electromagnetic Induction ◽  
Three Dimensional ◽  
Technical Requirement ◽  
Simulation Design ◽  
Paper Drying ◽  
Electromagnetic Heating ◽  
Dimensional Simulation ◽  
Drying Technology ◽  
Steam Drying

The electromagnetic technology of drying Paper is that we use the principle of electromagnetic heating to dry paper, which is a new paper drying technology and quite different from the traditional steam drying . This thesis is based on the principle of electromagnetic induction, combined with technical requirement of paper drying. We used the AutoCAD software design a laboratory drying device with electromagnetic, and analyzed various parts of the selection and structure, by using UG software solid modeling, assembly modeling and other modules design a three-dimensional simulation of the various parts of the electromagnetic dryer device. The simulation graphics shown that the simulation design of electromagnetic dryer is more success, which can meet the requirements of drying paper evenly.

scholarly journals RANCANG BANGUN SISTEM PEMUTUS ARUS SEBAGAI PENGAMAN TEMPERATUR BERLEBIH PADA INKUBATOR BAYI

2021 ◽  
Vol 16 (1) ◽  
pp. 162-171
Author(s):  
Indah Nursyamsi Handayani ◽  
Wike Kristianti ◽  
Mamurotun Mamurotun ◽  
Andy Sambiono
Keyword(s):  
Circuit Breaker ◽  
Hardware Design ◽  
Health Care Facilities ◽  
Sensor Data ◽  
Temperature Control System ◽  
Technology Readiness ◽  
Testing System ◽  
Temperature Parameter ◽  
State Relay ◽  
Design And Testing

Several countries in the world, including Indonesia, have reported baby-care accidents in the baby incubator due to the failure of the temperature control system to maintain a stable temperature. Therefore, this study reports the design of an circuit breaker system as an over-temperature safety in a baby incubator. Experimentally, the prototype consists of hardware design, software design, and testing system design. The hardware design has four main part, sensing layer using PT1000 as a temperature sensor, data processing layer using an ESP32 microcontroller, a circuit breaker system using a solid-state relay as an electronic switching, and LCD as a display. System testing has been done by evaluating the temperature readings on a prototype against the HTC-02 digital thermometer instrument and carried out in the electromedical engineering laboratory. The results show the accuracy of the temperature parameter is 99% and the circuit breaker system is able to cut the current from the power supply to the appliance when the temperature is more than 39°C which is indicated by an incandescent lamp "off" where this is equivalent to a heater at the baby incubator is in the "off" condition. From the results of this test, it can be concluded that the circuit breaker system as a safety over temperature in the baby incubator has functioned according to the design.Recommended the development of this prototype needs to be followed up by testing on low-tech baby incubators available at basic health care facilities so as to improve technology readiness to be effective in the community.

scholarly journals SPES3 Facility RELAP5 Sensitivity Analyses on the Containment System for Design Review

2012 ◽  
Vol 2012 ◽  
pp. 1-19 ◽  
Author(s):  
Andrea Achilli ◽  
Cinzia Congiu ◽  
Roberta Ferri ◽  
Fosco Bianchi ◽  
Paride Meloni ◽  
...  
Keyword(s):  
Nuclear Fission ◽  
Sensitivity Analyses ◽  
Medium Size ◽  
Facility Design ◽  
Simulation Design ◽  
Containment System ◽  
Coupled Codes ◽  
Hydraulic Conditions ◽  
Weak Points ◽  
Design And Testing

An Italian MSE R&D programme on Nuclear Fission is funding, through ENEA, the design and testing of SPES3 facility at SIET, for IRIS reactor simulation. IRIS is a modular, medium size, advanced, integral PWR, developed by an international consortium of utilities, industries, research centres and universities. SPES3 simulates the primary, secondary and containment systems of IRIS, with 1:100 volume scale, full elevation and prototypical thermal-hydraulic conditions. The RELAP5 code was extensively used in support to the design of the facility to identify criticalities and weak points in the reactor simulation. FER, at Zagreb University, performed the IRIS reactor analyses with the RELAP5 and GOTHIC coupled codes. The comparison between IRIS and SPES3 simulation results led to a simulation-design feedback process with step-by-step modifications of the facility design, up to the final configuration. For this, a series of sensitivity cases was run to investigate specific aspects affecting the trend of the main parameters of the plant, as the containment pressure and EHRS removed power, to limit fuel clad temperature excursions during accidental transients. This paper summarizes the sensitivity analyses on the containment system that allowed to review the SPES3 facility design and confirm its capability to appropriately simulate the IRIS plant.

Sign in / Sign up

Export Citation Format

Share Document