Melt Flow Behavior of Polymer Matrix Extrusion for Fused Deposition Modeling (FDM)

2014 ◽  
Vol 660 ◽  
pp. 89-93 ◽  
Author(s):  
Nasuha Sa'ude ◽  
Mustaffa Ibrahim ◽  
Mohd Halim Irwan Ibrahim
Keyword(s):  
Fused Deposition Modeling ◽  
Flow Behavior ◽  
Acrylonitrile Butadiene Styrene ◽  
Extrusion Process ◽  
Melt Flow ◽  
Element Analysis ◽  
Fused Deposition ◽  
Ansys Cfx ◽  
Deposition Modeling ◽  
Higher Temperature

This paper presents the melt flow behavior (MFB) of an acrylonitrile butadiene styrene (ABS), High Density Polyethlene (HDPE), Polyproplene (PP) and a combination of ABS-Iron in the extrusion process. In this study, the effect MFB of variety's polymers and ABS mix with 10% Iron material was investigated based on the viscosity, density, thermal conductivity, melting temperature and specific heat material properties. The MFB of FDM system was investigated using Finite-Element Analysis (FEA) by ANSYS CFX 12. Based on the result obtained, it was found that, the material velocity increase when the nozzle diameter is smaller than the entrance diameter. The higher temperature distribution along the MFB of ABS mix with 10% Iron is 43.15 K compared with original ABS, which is 539.15K.

Melt Flow Behavior of Metal Filled in Polymer Matrix for Fused Deposition Modeling (FDM) Filament

2014 ◽  
Vol 660 ◽  
pp. 84-88 ◽  
Author(s):  
Nasuha Sa'ude ◽  
Mustaffa Ibrahim ◽  
Mohd Halim Irwan Ibrahim
Keyword(s):  
Polymer Matrix ◽  
Fused Deposition Modeling ◽  
Plastic Material ◽  
Flow Behavior ◽  
Acrylonitrile Butadiene Styrene ◽  
Melt Flow ◽  
Element Analysis ◽  
Fused Deposition ◽  
Ansys Cfx ◽  
Exit Nozzle

This paper presents the melt flow behavior (MFB) of an acrylonitrile butadiene styrene (ABS), Polyproplene (PP), Polylactic Acid (PLA), ABS mix 10% Copper and ABS mix 10% Iron in the simulation. In this study, the effect MFB of ABS mix with 10% Iron and 10% Copper material was investigated based on the viscosity, density, thermal conductivity, melting temperature and specific heat of material properties. The MFB of metal filled in polymer matrix composite (PMC) through the FDM nozzle was investigated using Finite-Element Analysis (ANSYS CFX 12). Based on the result obtained, pressure outlet of mix ABS copper and ABS iron in extruder nozzle was higher value compared with others plastic material. The velocity was increased since the nozzle diameter is smaller than the entrance diameter. It can be observed that, the melt flow behavior of metal filled in PMC are affected on pressure drop, velocity and the nozzle size at the exit nozzle.

scholarly journals Melt Flow Index of Recycle ABS for Fused Deposition Modeling (FDM) Filament

2015 ◽  
Vol 773-774 ◽  
pp. 3-7 ◽  
Author(s):  
Nasuha Sa'ude ◽  
Khairu Kamarudin ◽  
Mustaffa Ibrahim ◽  
Mohd Halim Irwan Ibrahim
Keyword(s):  
Material Properties ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Melt Flow Index ◽  
Flow Index ◽  
Melt Flow ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Higher Temperature ◽  
Butadiene Styrene

This paper presents the melt flow index (MFI) of acrylonitrile butadiene styrene (ABS) and recycle ABS filament wire for Fused Deposition Modeling (FDM) machine. In this study, the effect of MFI on recycle ABS material was investigated experimentally based on the melting temperature, density, screw speed and material properties. The MFI result on ABS recycle in wire filament was investigated using Melt Indexer Machine (MIM). Based on the result obtained, it was found that, ABS recycle was increase the density and MFI results. It can be observed that, the higher temperature was melt the recycle ABS material through the MIM and extruder machine.

scholarly journals Synthesis of Dimethyl Octyl Aminoethyl Ammonium Bromide and Preparation of Antibacterial ABS Composites for Fused Deposition Modeling

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2229
Author(s):  
Yue Wang ◽  
Sen Wang ◽  
Yaocheng Zhang ◽  
Jianguo Mi ◽  
Xuejia Ding
Keyword(s):  
Fused Deposition Modeling ◽  
Antibacterial Properties ◽  
Acrylonitrile Butadiene Styrene ◽  
Extrusion Process ◽  
Ammonium Bromide ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Two Phases ◽  
Modification Of Materials ◽  
Daily Application

Additive manufacturing (AM) demonstrates benefits in the high-precision production of devices with complicated structures, and the modification of materials for AM is an urgent need. To solve the bacterial infection of medical devices in their daily application, dimethyl octyl aminoethyl ammonium bromide (octyl-QDED), an organic antibacterial agent, was synthesized via the quaternary ammonium reaction. Then, the synthesized octyl-QDED was blended with acrylonitrile butadiene styrene (ABS) through the melt extrusion process to prepare antibacterial composite filaments for fused deposition modeling (FDM). The entire preparation processes were convenient and controllable. Characterizations of the structure and thermal stability of octyl-QDED confirmed its successful synthesis and application in the subsequent processes. The introduced maleic acid in the blending process acted as a compatibilizer, which improved the compatibility between the two phases. Characterizations of the rheological and mechanical properties proved that the addition of octyl-QDED made a slight difference to the comprehensive performance of the ABS matrix. When the content of octyl-QDED reached 3 phr, the composites showed excellent antibacterial properties. The prepared antibacterial composite filaments for FDM demonstrated great potential in medical and surgical areas.

scholarly journals Carbon Nanotube-Based Composite Filaments for 3D Printing of Structural and Conductive Elements

2021 ◽  
Vol 11 (3) ◽  
pp. 1272
Author(s):  
Bartłomiej Podsiadły ◽  
Piotr Matuszewski ◽  
Andrzej Skalski ◽  
Marcin Słoma
Keyword(s):  
Carbon Nanotubes ◽  
Fused Deposition Modeling ◽  
Supply Voltage ◽  
Acrylonitrile Butadiene Styrene ◽  
Structural Elements ◽  
Filling Fraction ◽  
Fused Deposition ◽  
Structural Electronics ◽  
Measured Sample ◽  
Deposition Modeling

In this publication, we describe the process of fabrication and the analysis of the properties of nanocomposite filaments based on carbon nanotubes and acrylonitrile butadiene styrene (ABS) polymer for fused deposition modeling (FDM) additive manufacturing. Polymer granulate was mixed and extruded with a filling fraction of 0.99, 1.96, 4.76, 9.09 wt.% of CNTs (carbon nanotubes) to fabricate composite filaments with a diameter of 1.75 mm. Detailed mechanical and electrical investigations of printed test samples were performed. The results demonstrate that CNT content has a significant influence on mechanical properties and electrical conductivity of printed samples. Printed samples obtained from high CNT content composites exhibited an improvement in the tensile strength by 12.6%. Measurements of nanocomposites’ electrical properties exhibited non-linear relation between the supply voltage and measured sample resistivity. This effect can be attributed to the semiconductor nature of the CNT functional phase and the occurrence of a tunnelling effect in percolation network. Detailed I–V characteristics related to the amount of CNTs in the composite and the supply voltage influence are also presented. At a constant voltage value, the average resistivity of the printed elements is 2.5 Ωm for 4.76 wt.% CNT and 0.15 Ωm for 9.09 wt.% CNT, respectively. These results demonstrate that ABS/CNT composites are a promising functional material for FDM additive fabrication of structural elements, but also structural electronics and sensors.

Simulation of the viscoplastic extrusion process using the radial point interpolation meshless method

2021 ◽  
pp. 146442072098858
Author(s):  
ROSS Costa ◽  
J Belinha ◽  
RM Natal Jorge ◽  
DES Rodrigues
Keyword(s):  
Meshless Method ◽  
Fused Deposition Modeling ◽  
Interpolation Method ◽  
Extrusion Process ◽  
Fused Deposition ◽  
Radial Point Interpolation ◽  
Large Growth ◽  
Point Interpolation Method ◽  
Point Interpolation ◽  
Deposition Modeling

Additive manufacturing is an emergent technology, which witnessed a large growth demanded by the consumer market. Despite this growth, the technology needs scientific regulation and guidelines to be reliable and consistent to the point that is feasible to be used as a source of manufactured end-products. One of the processes that has seen the most significant development is the fused deposition modeling, more commonly known as 3D printing. The motivation to better understand this process makes the study of extrusion of materials important. In this work, the radial point interpolation method, a meshless method, is applied to the study of extrusion of viscoplastic materials, using the formulation originally intended for the finite element method, the flow formulation. This formulation is based on the reasoning that solid materials under those conditions behave like non-Newtonian fluids. The time stepped analysis follows the Lagrangian approach taking advantage of the easy remeshing inherent to meshless methods. To validate the newly developed numerical tool, tests are conducted with numerical examples obtained from the literature for the extrusion of aluminum, which is a more common problem. Thus, after the performed validation, the algorithm can easily be adapted to simulate the extrusion of polymers in fused deposition modeling processes.

Influence of Part Orientation on the Surface Roughness in the Process of Fused Deposition Modeling

2021 ◽  
Vol 896 ◽  
pp. 29-37
Author(s):  
Ján Milde ◽  
František Jurina ◽  
Jozef Peterka ◽  
Patrik Dobrovszký ◽  
Jakub Hrbál ◽  
...  
Keyword(s):  
Surface Roughness ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Orientation Angle ◽  
Acrylonitrile Butadiene Styrene ◽  
Lower Surface ◽  
Geometrical Model ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Part Orientation

The article focused on the influence of part orientation on the surface roughness of cuboid parts during the process of fabricating by FDM technology. The components, in this case, is simple cuboid part with the dimensions 15 mm x 15mm x 30 mm. A geometrical model is defined that considers the shape of the material filaments after deposition, to define a theoretical roughness profile, for a certain print orientation angle. Five different print orientations in the X-axis of the cuboid part were set: 0°, 30°, 45°, 60°, and 90°. According to previous research in the field of FDM technology by the author, the internal structure (infill) was set at the value of 70%. The method of 3D printing was the Fused Deposition Modeling (FDM) and the material used in this research was thermoplastic ABS (Acrylonitrile butadiene styrene). For each setting, there were five specimens (twenty five prints in total). Prints were fabricated on a Zortrax M200 3D printer. After the 3D printing, the surface “A” was investigated by portable surface roughness tester Mitutoyo SJ-210. Surface roughness in the article is shown in the form of graphs (Fig.7). Results show increase in part roughness with increasing degree of part orientation. When the direction of applied layers on the measured surface was horizontal, significant improvement in surface roughness was observed. Findings in this paper can be taken into consideration when designing parts, as they can contribute in achieving lower surface roughness values.

Electrical Properties of Additively Manufactured Acrylonitrile Butadiene Styrene/Carbon Nanotube Nanocomposite

2018 ◽  
Author(s):  
Dominic Thaler ◽  
Nahal Aliheidari ◽  
Amir Ameli
Keyword(s):  
Electrical Conductivity ◽  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Functional Materials ◽  
Acrylonitrile Butadiene Styrene ◽  
Extrusion Process ◽  
Print Quality ◽  
Fused Deposition ◽  
Order Of Magnitude ◽  
Butadiene Styrene

Additive manufacturing is an emerging method to produce customized parts with functional materials without big investments. As one of the common additive manufacturing methods, fused deposition modeling (FDM) uses thermoplastic-based feedstock. It has been recently adapted to fabricate composite materials too. Acrylonitrile butadiene styrene (ABS) is the most widely used material as FDM feedstock. However, it is an electrically insulating polymer. Carbon Nanotubes (CNTs) on the other hand are highly conductive. They are attractive fillers because of their high aspect ratio, and excellent mechanical and physical properties. Therefore, a nanocomposite of these two materials can give an electrically conductive material that is potentially compatible with FDM printing. This work focuses on the investigation of the relationships between the FDM process parameters and the electrical conductivity of the printed ABS/CNT nanocomposites. Nanocomposite filaments with CNT contents up to 10wt% were produced using a twin-screw extruder followed by 3D printing using FDM method. The starting material was pellets from a masterbatch containing 15 wt% CNT. Compression-molded samples of ABS/CNT were also prepared as the bulk baselines. The effects of CNT content and nozzle size on the through-layer and in-layer electrical conductivity of the printed nanocomposites were analyzed. Overall, a higher percolation threshold was observed in the printed samples, compared to that of the compression-molded counterparts. This resulted in the conductivity of the printed samples that is at least one order of magnitude lower. Moreover, at CNT contents up to 5 wt%, the in-layer conductivity of the printed samples was almost two orders of magnitudes higher than that in the through-layer direction. In ABS/3 wt% CNT samples, the through-layer conductivity continuously decreased as the nozzle diameter was decreased from 0.8 mm to 0.35 mm. These variations in the electrical conductivity were explained in terms of the CNT alignment, caused by the extrusion process during the print, quality of interlayer bonding during deposition, and the voids created due to the discrete nature of the printing process.

scholarly journals Comparison Of FEA Simulations And Experimental Results For As-Built Additively Manufactured Dogbone Specimens

2021 ◽  
Author(s):  
Prathamesh Baikerikar ◽  
Cameron J Turner
Keyword(s):  
Fused Deposition Modeling ◽  
Experimental Tests ◽  
Continuum Models ◽  
Element Analysis ◽  
Fused Deposition ◽  
Accuracy And Precision ◽  
Structure Strength ◽  
Deposition Modeling ◽  
End Use ◽  
Strength And Stiffness

Abstract Parts built using Fused Deposition Modeling (FDM – an additive manufacturing technology) differ from their design model in terms of their microstructure and material properties. These differences lead to a certain amount of ambiguity regarding the structure, strength and stiffness of the final FDM part. Increasing use of FDM parts as end use products, necessitates accurate simulations and analyses during part design. However, analysis methods such as Finite Element Analysis, are used for analysis of continuum models, and may not accurately represent the non-continuous non-linear FDM parts. Therefore, it is necessary to determine the accuracy and precision of FEA for FDM parts. The goal of this study is to compare FEA simulations of the as-built geometries with the experimental tests of actual FDM parts. Dogbone geometries that include different infill patterns are tested under tensile loading and later simulated using FEA. This study found that FEA results are not always an accurate or reliable means of predicting FDM part behaviors.

Sign in / Sign up

Export Citation Format

Share Document