Experimental Study on Evolution of Rock Damage Rule in the Condition of Conventional Three Axis Compression

2014 ◽  
Vol 670-671 ◽  
pp. 432-436
Author(s):  
Bing He
Keyword(s):  
Damage Mechanics ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Volumetric Strain ◽  
Continuum Damage Mechanics ◽  
Continuum Damage ◽  
Conventional Triaxial Compression ◽  
Axis Compression ◽  
Plastic Volumetric Strain ◽  
Damage Rule

Based on continuum damage mechanics, by defining the initial and critical damage value, because of the plastic volumetric strain of the specimen, we established the calculation methods of the rock specimen’s damage value. Through the conventional triaxial compression test of the shale, we find that damage value D changes as axial strain changes during compression, and summarizes its variation.

Hydromechanical behaviour of overconsolidated unsaturated soil in undrained conditions

2019 ◽  
Vol 56 (11) ◽  
pp. 1609-1621 ◽  
Author(s):  
Shengshen Wu ◽  
Annan Zhou ◽  
Jie Li ◽  
Jayantha Kodikara ◽  
Wen-Chieh Cheng
Keyword(s):  
Effective Stress ◽  
Unsaturated Soils ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Volumetric Strain ◽  
Degree Of Saturation ◽  
Triaxial Tests ◽  
Conventional Triaxial Compression ◽  
Hydromechanical Behaviour ◽  
Undrained Conditions

Hydromechanical behaviour of an unsaturated silt with various suctions and different overconsolidated ratios (OCRs) was investigated through a series of undrained triaxial tests (constant water contents, CW). All the samples were prepared from the slurry state. Different OCRs (= 1, 2, 4, and 8 in net stress) were achieved by unloading the samples to 400, 200, 100, and 50 kPa from an initial confining net pressure of 400 kPa. Then the samples were dried to various suctions (0, 100, 200, 300, and 400 kPa). Unsaturated samples with different OCRs were then sheared at CW conditions following the conventional triaxial compression (CTC) paths. Full hydromechanical responses including the changes in deviator stress, stress ratio, volumetric strain, suction, and degree of saturation with axial strain were monitored and are presented in this paper. Some key findings include (i) the critical state for unsaturated soils with different OCRs can be well defined by Bishop’s effective stress; (ii) the peak strength in Bishop’s effective stress increases with increase of OCR, but decreases with increase of suction in the undrained condition; and (iii) the volume change of unsaturated soils in undrained conditions is related to OCRs and the volume of pore air.

Fatigue Life of the Human Teeth: A Continuum Damage Approach

2019 ◽  
Vol 43 ◽  
pp. 1-19
Author(s):  
Theddeus Tochukwu Akano
Keyword(s):  
Fatigue Life ◽  
Damage Mechanics ◽  
Stress Amplitude ◽  
Continuum Damage Mechanics ◽  
Continuum Damage ◽  
Elastoplastic Model ◽  
Human Teeth ◽  
Proposed Model ◽  
Number Of Cycles ◽  
Cycles To Failure

Normal oral food ingestion processes such as mastication would not have been possible without the teeth. The human teeth are subjected to many cyclic loadings per day. This, in turn, exerts forces on the teeth just like an engineering material undergoing the same cyclic loading. Over a period, there will be the creation of microcracks on the teeth that might not be visible ab initio. The constant formation of these microcracks weakens the teeth structure and foundation that result in its fracture. Therefore, the need to predict the fatigue life for human teeth is essential. In this paper, a continuum damage mechanics (CDM) based model is employed to evaluate the fatigue life of the human teeth. The material characteristic of the teeth is captured within the framework of the elastoplastic model. By applying the damage evolution equivalence, a mathematical formula is developed that describes the fatigue life in terms of the stress amplitude. Existing experimental data served as a guide as to the completeness of the proposed model. Results as a function of age and tubule orientation are presented. The outcomes produced by the current study have substantial agreement with the experimental results when plotted on the same axes. There is a notable difference in the number of cycles to failure as the tubule orientation increases. It is also revealed that the developed model could forecast for any tubule orientation and be adopted for both young and old teeth.

Modelling the asymmetric tension–compression properties of additively manufactured alloys using continuum damage mechanics

2021 ◽  
pp. 146442072110134
Author(s):  
A Nayebi ◽  
H Rokhgireh ◽  
M Araghi ◽  
M Mohammadi
Keyword(s):  
Damage Mechanics ◽  
Continuum Damage Mechanics ◽  
Element Model ◽  
Continuum Damage ◽  
Compression Tests ◽  
Compression Properties ◽  
Mechanics Model ◽  
Stress Components ◽  
Tension And Compression ◽  
Closure Effect

Additively manufactured parts often comprise internal porosities due to the manufacturing process, which needs to be considered in modelling their mechanical behaviour. It was experimentally shown that additively manufactured parts’ tensile and compressive mechanical properties are different for various metallic alloys. In this study, isotropic continuum damage mechanics is used to model additively manufactured alloys’ tension and compression behaviours. Compressive stress components can shrink discontinuities present in additively manufactured alloys. Therefore, the crack closure effect was employed to describe different behaviours during uniaxial tension and compression tests. A finite element model embedded in an ABAQUS’s UMAT format was developed to account for the isotropic continuum damage mechanics model. The numerical results of tension and compression tests were compared with experimental observations for additively manufactured maraging steel, AlSi10Mg and Ti-6Al-4V. Stress–strain curves in tension and compression of these alloys were obtained using the continuum damage mechanics model and compared well with the experimental results.

Creep Life Prediction of Aircraft Turbine Disc Alloy Using Continuum Damage Mechanics

2017 ◽  
Vol 38 (1) ◽  
pp. 25-30
Author(s):  
Yan-Feng Li ◽  
Zhisheng Zhang ◽  
Chenglin Zhang ◽  
Jie Zhou ◽  
Hong-Zhong Huang
Keyword(s):  
Numerical Analysis ◽  
Test Data ◽  
Life Prediction ◽  
Damage Mechanics ◽  
Continuum Damage Mechanics ◽  
Creep Model ◽  
Continuum Damage ◽  
Creep Life ◽  
Creep Life Prediction ◽  
Turbine Disc

Abstract This paper deals with the creep characteristics of the aircraft turbine disc material of nickel-base superalloy GH4169 under high temperature. From the perspective of continuum damage mechanics, a new creep life prediction model is proposed to predict the creep life of metallic materials under both uniaxial and multiaxial stress states. The creep test data of GH4169 under different loading conditions are used to demonstrate the proposed model. Moreover, from the perspective of numerical simulation, the test data with analysis results obtained by using the finite element analysis based on Graham creep model is carried out for comparison. The results show that numerical analysis results are in good agreement with experimental data. By incorporating the numerical analysis and continuum damage mechanics, it provides an effective way to accurately describe the creep damage process of GH4169.

Development of continuum damage in the creep rupture of notched bars

1984 ◽  
Vol 311 (1516) ◽  
pp. 103-129 ◽  
Keyword(s):  
New York ◽  
Damage Mechanics ◽  
Axial Stress ◽  
Numerical Procedure ◽  
Creep Damage ◽  
Continuum Damage Mechanics ◽  
Constant Load ◽  
Creep Rupture ◽  
Continuum Damage ◽  
Discrete Crack

The creep rupture of circumferentially notched, circular tension bars which are subjected to constant load for long periods at constant temperature is studied both experimentally and by using a time-iterative numerical procedure which describes the formation and growth of creep damage as a field quantity. The procedure models the development of failed or cracked regions of material due to the growth and linkage of grain boundary defects. Close agreement is shown between experimental and theoretical values of the representative rupture stress, of the zones of creep damage and of the development of cracks for circular (Bridgman, Studies in large plastic flow and fracture , New York: McGraw-Hill (1952)) and British Standard notched specimens (B.S. no. 3500 (1969)). The minimum section of the circular notch is shown to be subjected to relatively uniform states of multi-axial stress and damage while the B.S. notch is shown to be subjected to non-uniform stress and damage fields in which single cracks grow through relatively undamaged material. The latter situation is shown to be analogous to the growth of a discrete crack in a lightly damaged continuum. The continuum damage mechanics theory presented here is shown to be capable of accurately predicting these extreme types of behaviour.

Cross-Ply Laminates under Static Three-Point Bending: A Numerical Development Model

2012 ◽  
Vol 498 ◽  
pp. 42-54 ◽  
Author(s):  
S. Benbelaid ◽  
B. Bezzazi ◽  
A. Bezazi
Keyword(s):  
Numerical Model ◽  
Damage Mechanics ◽  
Progressive Failure ◽  
Damage Model ◽  
Continuum Damage Mechanics ◽  
Failure Criteria ◽  
Continuum Damage ◽  
Damage Development ◽  
Element Analysis ◽  
Progressive Failure Analysis

This paper considers damage development mechanisms in cross-ply laminates using an accurate numerical model. Under static three points bending, two modes of damage progression in cross-ply laminates are predominated: transverse cracking and delamination. However, this second mode of damage is not accounted in our numerical model. After a general review of experimental approaches of observed behavior of laminates, the focus is laid on predicting laminate behavior based on continuum damage mechanics. In this study, a continuum damage model based on ply failure criteria is presented, which is initially proposed by Ladevèze. To reveal the effect of different stacking sequence of the laminate; such as thickness and the interior or exterior disposition of the 0° and 90° oriented layers in the laminate, an equivalent damage accumulation which cover all ply failure mechanisms has been predicted. However, the solution algorithm using finite element analysis which implements progressive failure analysis is summarized. The results of the numerical computation have been justified by the previous published experimental observations of the authors.

Sign in / Sign up

Export Citation Format

Share Document