Mobile Communication Inter-Symbol Crosstalk Cancellation Based on Calman Digital Equalizer Filter

2014 ◽  
Vol 716-717 ◽  
pp. 1262-1266
Author(s):  
Li Hua Sun ◽  
Cui Cui Huang ◽  
Liang Jun Yu

In the digital mobile communication signal transmission system, the inter-symbol interference is one of the main factors affecting the performance. In order to make the error rate reducing to a minimum, this paper designs a new Calman digital equalization filter. It is based on Calman filter principle, and establishes the control mathematical model of observation equation and state equation, and uses MATLAB programming to realize the algorithm. In order to verify the effectiveness and reliability of this filter, this paper uses filter toolbox of MATAB to do numerical simulation on the filtering effect. Through comparing with normal digital equalization filter effect, after adding the Calman digital equalizer filter, the feedback signal is conformed to the reference signal. The duty ratio of SPWM follows the basic changing law, so as to maximize the elimination of crosstalk inter-symbol. It provides reference data for the research on mobile communication inter-symbol interference.

2020 ◽  
Vol 15 (1) ◽  
pp. 808-818
Author(s):  
Yifan Wang ◽  
Kefu Liu ◽  
Xiaowei Xiang ◽  
Caihui Zhu ◽  
Hao Wang

AbstractThe radiofrequency-induced intestine fusion has been widely studied as an alternative for traditional suture in surgery, but fusion quality cannot be evaluated directly. Impedance measurement can evaluate fusion quality, but the relation between impedance and the fusion quality needs optimization for best results. The present study reports the optimum resistance of small intestine fusion. As the feedback signal, resistance was considered the indicator of the fusion completion for the device design of intestine fusion and an in-depth study of microstructure change. A self-design pulse source was used for the small intestine fusion with adjustable voltage, duty ratio, frequency and output time. A frequency of 440 kHz was set, whereas voltage, output time and compression pressure (CP) of the small intestine were independent variables. Different conditions of voltage, CP and time were investigated for achieving the highest burst pressure (BP) measured with a pressure gauge and a peristaltic pump. Each parameter of the equivalent circuit model was calculated by an experimental waveform. Hematoxylin–eosin staining of fusion samples was used for assessing the quality of fusion. The real-time current was measured and recorded during the fusion for the calculation of capacitance and resistance. The highest BP of 38.9 mmHg was achieved with a CP of 900 kPa, a voltage of 50 V and a time of 5 s. Finally, an optimum extracellular resistance range of 61.0–86.2 Ω was found as the optimum resistance for the end of fusion, thus indicating automatic fusion with the best fusion quality.


Author(s):  
Xingya Ding ◽  
Gang Shen ◽  
Xiang Li ◽  
Yu Tang

In this article, the position control problem of electro-hydraulic servo systems with feedback signal transmission delay is studied. In order to improve the control accuracy of the system, a hybrid controller which combines a delay observer, a nonlinear disturbance observer and a backstepping controller is proposed. The controller has the characteristics of compensating the delay of signal transmission, restraining the uncertain disturbance of control systems and high control precision. In order to verify the stability and validity of the proposed hybrid controller, a single-degree-of-freedom electro-hydraulic shaking table is used to verify the experimental results. The experimental results show that the proposed controller has better control effects than proportional integral derivative and backstepping controller.


2014 ◽  
Vol 1070-1072 ◽  
pp. 994-1000
Author(s):  
Lu Li ◽  
Guo Qing Jiang ◽  
Tian Ye Niu ◽  
Yi Wang ◽  
Yong Lu ◽  
...  

Since the strong coupling property between partial discharge and external interference, how to obtain an acceptable Resolution is a huge challenge during partial discharge measure. In terms of interference suppression, many methods associated with analog and digital technique are devised. Whatever the methods are, the way to eliminate pulse interference is the toughest task due to the closest feature in the respect of time and frequency field compared with partial discharge. In this paper, we propose a wavelet based interference separation method to separate partial discharge signal compounding with random pulse signal, mobile communication signal and white noise, providing valid data for the following partial discharge measurement. Both simulation and practical results verify the effectiveness of our proposed method.


2014 ◽  
Vol 716-717 ◽  
pp. 1267-1271
Author(s):  
Liang Jun Yu ◽  
Li Hua Sun ◽  
Cui Cui Huang

Intersymbol Interference (ISI) problem is one of the main factors affecting the baseband transmission performance of mobile communication’s digital signal which can not only reduce the transmission quality of the information but also can result in misinformation and false pass of information and provide troubles to the user and communications. In order to minimize the error rate, we propose a new digital equalization filter and establish the basic model of the digital filter and introduce non-linear Kalman observation equation and the state equation into the model and design partial differential mathematical model of the Kalman filter and develop MATLAB solver based on the mathematical model. In order to verify the validity and reliability of Kalman filter algorithms and mathematical procedures designed in this paper, it uses MATLAB toolbox to simulate the filter of mobile crosstalk signal and obtains amplitude-frequency characteristics and time-domain characteristics before and after filtering. By comparison, we can see that the filter can eliminate the high frequency crosstalk signal which provides technical reference for the study of the problem of crosstalk between the mobile communication codes.


Author(s):  
Farid Baskoro ◽  
Miftahur Rohman ◽  
Aristyawan Putra Nurdiansyah

Serial Peripheral Interface (SPI) is a synchronous serial communication whose data or signal transmission involves Chip Select (CS) or Slave Select (SS) pins, Serial Clock (SCK), Master Out Slave In (MOSI), and Master In Slave Out (MISO). In the Arduino Uno, there are four pins that allow Arduino Uno to perform SPI communication. In this research, SPI communication is implemented to expand the output of the Arduino Uno by using the features of the MCP23S17 IC so that the Arduino Uno, which initially has 20 output pins, can expand to 36 output pins.The results of the research show that the Arduino Uno manages to control 36 output pins. 16 output pins from the MCP23S17, 16 output pins from the Arduino Uno, and 4 pins are used for the SPI communication line. The results of this study also show the form of the SPI communication signal from Arduino Uno in declaring 21 registers on MCP23S17, declaring the MCP23S17 pin register as output, and implementing the output using LEDs.


Author(s):  
Roman Yershov ◽  

Urgency of the research. A dual-range, four-quadrant position stabilization system (PSS) of a brushless direct current motor (BLDC) as a part of movable platform (MP), in which the power stage is based on a quasi-resonant pulse converter (QRPC), has the better speed and accuracy characteristics in comparison with hard-switching PWM-based converters. Target setting. The BLDC PSS can be built on the basis of the classic multi-loop control system (MLCS), or on the pulse-frequency (PF-) domain. In PF-domain the task of speed control is transformed into the frequency comparing and matching task, and the position control is transformed into the phasecomparing and matching between the reference signal and the feedback signal. The development of specialized digital blocks of a frequency comparator (FK) and a phase comparator (PC) to perform the above tasks is a non-trivial task. Actual scientific researches and issues analysis. The earliest solutions of the FC, which should be correctly called the ‘frequency detector’ (FD), were implemented mixed-signal (contained both analog and digital nodes) due to their usage in a high-frequency phase-locked loop (PLL) system. A full-featured FC consists of two counters, comparator, a FD block, control finite-state machine (FSM), and a specialized combinational circuit. Uninvestigated parts of general matters defining. Existing FC blocks do not return a quantitative relation between measured frequencies, which can be used to predict dynamics, and are insensitive to the detection of small misalignments between frequencies, that, in turn, creates instability of determining the frequencies equality state. Existing PC blocks are unstable when the frequency of one of the measured signals reaches the system clock frequency, and also do not take into account the edges incoming order of the measured signals. The research objective. The article is devoted to the study and development of the structure of pure-digital FC and PC blocks, which will eliminate the disadvantages of existing solutions and are oriented for integration into PSS with QRPC in the power stage and MLCS operates in a PF-domain. The statement of basic materials. A novel technical solutions is proposed, developed and tested for pure-digital blocks of the FC and PC built on the basis of the field-programmable gate array (FPGA) by means of the hardware description language (VHDL). They allow not only to measure the sign of the inequality of frequency and phase between two periodic signals, but also to obtain the difference numerical values between them. Conclusions. The installation of the FC and PC blocks into the BLDC PSS leads to a significant reducing of FPGA hardware resources utilization and to the high reliability and noise immunity of the MLCS through the unruptured (continiously) nature of the signals. Both the proposed blocks are novel and have eliminated the inherent disadvantages of the existing blocks of the FC and PC due to the installation of additional digital nodes − synchronizers (pulse shorters and edge detectors), and also a hysteresis node that leads to increase the stability and solve the problem of detection near-to-equal frequencies and phases.


Sign in / Sign up

Export Citation Format

Share Document