scholarly journals Polishing of Chemical Oxygen Demand (COD) Using Moving Bed Bio-Reactor

2015 ◽  
Vol 773-774 ◽  
pp. 1281-1285
Author(s):  
Jamal Ali Kawan ◽  
Rakmi Abd-Rahman ◽  
Othman bin Jaafar ◽  
Fatihah Suja
Keyword(s):  
Chemical Oxygen Demand ◽  
Municipal Wastewater ◽  
Removal Rate ◽  
Research Work ◽  
Real Life ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
Moving Bed ◽  
Building Engineering

The pilot-scale experiment in moving bed biofilm reactor (MBBR) with a capacity of 433 L was carried out for this study with real life situations, it was decided that the complete research work must be done under as realistic conditions as possible,i.e.with real municipal wastewater, chemical free and with local commercially available products such as carriers for biofilm reactor. The reactor was start-up in 30/9/2013 up to date, Effluent from clarifier of STP used as influence of MBBR for polishing. MBBR is using continues down flow to polish effluent municipal wastewater from a faculty of new building engineering community in UKM to get the water free from main pollutant parameters, for reuse in the irrigation or discharge to the river. Laboratory experiments will conduct with different hydraulic retention time (HRT), filling ratio of plastic (Enviro Multi Media) in the MBBR about 5%. Aerobic reactors used the majority of the decaying organic material. An average removal rate of 41.75%, 32.85%, 24.80% and 35.77% of initial chemical oxygen demand (COD) were achieved under a HRT of 24hr, 12hr, 6hr and 2hr, respectively. The model simulated results showed good agreements with experimental results. The model could be employed in the design of a full-scale MBBR process for simultaneous removal of organic carbon from effluent STP.

Novel biofilm reactor for denitrification of municipal wastewater

2018 ◽  
Vol 78 (7) ◽  
pp. 1566-1575 ◽  
Author(s):  
S. S. Rathnaweera ◽  
B. Rusten ◽  
K. Korczyk ◽  
B. Helland ◽  
E. Rismyhr
Keyword(s):  
Carbon Source ◽  
Municipal Wastewater ◽  
Low Cost ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
Treated Wastewater ◽  
Removal Rates ◽  
Good Filter ◽  
Solids Removal

Abstract A pilot-scale CFIC® (continuous flow intermittent cleaning) reactor was run in anoxic conditions to study denitrification of wastewater. The CFIC process has already proven its capabilities for biological oxygen demand removal with a small footprint, less energy consumption and low cost. The present study focused on the applicability for denitrification. Both pre-denitrification (pre-DN) and post-denitrification (post-DN) were tested. A mixture of primary treated wastewater and nitrified wastewater was used for pre-DN and nitrified wastewater with ethanol as a carbon source was used for post-DN. The pre-DN process was carbon limited and removal rates of only 0.16 to 0.74 g NOx-N/m²-d were obtained. With post-DN and an external carbon source, 0.68 to 2.2 g NO3-Neq/m²-d removal rates were obtained. The carrier bed functioned as a good filter for both the larger particles coming with influent water and the bio-solids produced in the reactor. Total suspended solids removal in the reactor varied from 20% to 78% (average 45%) during post-DN testing period and 9% to 70% (average 29%) for pre-DN. The results showed that the forward flow washing improves both the DN function and filtration ability of the reactor.

Enhanced simultaneous nitri-denitrification in aerobic moving bed biofilm reactor containing polyurethane foam-based carrier media

2019 ◽  
Vol 79 (3) ◽  
pp. 510-517 ◽  
Author(s):  
Magdum Sandip ◽  
V. Kalyanraman
Keyword(s):  
Chemical Oxygen Demand ◽  
Nitrogen Removal ◽  
Oxygen Demand ◽  
Biofilm Reactor ◽  
Moving Bed Biofilm Reactor ◽  
Moving Bed ◽  
Removal Capacity ◽  
Pu Foam ◽  
Removal Efficiencies ◽  
Biofilm Support

Abstract Fluidization of carrier media for biofilm support and growth defines the moving bed biofilm reactor (MBBR) process. Major MBBR facilities apply virgin polyethylene (PE)-based circular plastic carrier media. Various carriers were studied to replace these conventional carriers, but polyurethane (PU) foam-based carrier media has not been much explored. This study evaluates the potential of PU foam carrier media in aerobic MBBR process for simultaneous nitri-denitrification (SND). Two parallel reactors loaded with conventional PE plastic (circular) and PU foam (cubical) carriers compared for their removal efficiencies of chemical oxygen demand (COD) and nitrogen contaminants from wastewater. Results indicate that average COD removal in MBBR containing PE plastic carrier media was 81%, compared to 83% in MBBR containing PU foam. Average ammonical and total nitrogen reduction was 71% and 59% for PU foam-based MBBR, compared to 60% and 42% for PE plastic-based MBBR. SND-based nitrogen removal capacity was doubled in aerobic MBBR filled with PU foam carrier media (27%), than MBBR containing PE plastic carrier media (13%). Cost economics also governs the commercial advantage for the application of PU foam-based carrier media in the MBBR process.

A pilot-scale study on PVA gel beads based integrated fixed film activated sludge (IFAS) plant for municipal wastewater treatment

2015 ◽  
Vol 73 (1) ◽  
pp. 113-123 ◽  
Author(s):  
Nitin Kumar Singh ◽  
Jasdeep Singh ◽  
Aakansha Bhatia ◽  
A. A. Kazmi
Keyword(s):  
Activated Sludge ◽  
Pilot Plant ◽  
Municipal Wastewater ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
16S Rrna Genes ◽  
Volume Index ◽  
Rrna Genes ◽  
Gel Beads

In the present study, a pilot-scale reactor incorporating polyvinyl alcohol gel beads as biomass carrier and operating in biological activated sludge mode (a combination of moving bed biofilm reactor (MBBR) and activated sludge) was investigated for the treatment of actual municipal wastewater. The results, during a monitoring period of 4 months, showed effective removal of chemical oxygen demand (COD), biological oxygen demand (BOD) and NH3-N at optimum conditions with 91%, ∼92% and ∼90% removal efficiencies, respectively. Sludge volume index (SVI) values of activated sludge varied in the range of 25–72 mL/g, indicating appreciable settling characteristics. Furthermore, soluble COD and BOD in the effluent of the pilot plant were reduced to levels well below discharge limits of the Punjab Pollution Control Board, India. A culture dependent method was used to enrich and isolate abundant heterotrophic bacteria in activated sludge. In addition to this, 16S rRNA genes analysis was performed to identify diverse dominant bacterial species in suspended and attached biomass. Results revealed that Escherichia coli, Pseudomonas sp. and Nitrosomonas communis played a significant role in biomass carrier, while Acinetobactor sp. were dominant in activated sludge of the pilot plant. Identification of ciliated protozoa populations rendered six species of ciliates in the plant, among which Vorticella was the most dominant.

Pumped flow biofilm reactors (PFBR) for treating municipal wastewater

2008 ◽  
Vol 57 (12) ◽  
pp. 1857-1865 ◽  
Author(s):  
E. O'Reilly ◽  
M. Rodgers ◽  
X.-M. Zhan
Keyword(s):  
Wastewater Treatment ◽  
Surface Area ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Cross Flow ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Ammonium Nitrogen ◽  
Biofilm Reactor ◽  
Bench Scale

A novel laboratory bench-scale sequencing batch biofilm reactor (SBBR) system was developed for the treatment of synthetic domestic strength wastewater, comprising two side-by-side 18 l reactor tanks, each containing a plastic biofilm media module. Aerobic and anoxic conditions in the biofilms were effected by intermittent alternate pumping of wastewater between the two reactors. With a media surface area loading rate of 4.2 g chemical oxygen demand (COD)/m2.d, the average influent COD, total nitrogen (TN) and ammonium-nitrogen (NH4-N) concentrations of 1021 mg/l, 97 mg/l and 54 mg/l, respectively, reduced to average effluent concentrations of 72 mg COD/l, 17.8 mg TN/l, and 5.5 mg NH4-N /l. Using a similar alternating biofilm exposure arrangement, a 16 person equivalent pilot (PE) plant was constructed at a local village treatment works to remove organic carbon from highly variable settled municipal wastewater and comprised two reactors, one positioned above the other, each containing a module of cross-flow plastic media with a surface area of 100 m2. Two different pumping sequences (PS) in the aerobic phase were examined where the average influent COD concentrations were 220 and 237 mg/l for PS1 and PS2, respectively, and the final average effluent COD was consistently less than 125 mg/l – the European Urban Wastewater Treatment Directive limit – with the best performance occurring in PS1. Nitrification was evident during both PS1 and PS2 studies. A 300 PE package treatment plant was designed based on the bench-scale and pilot-scale studies, located at a local wastewater treatment works and treated municipal influent with average COD, suspended solids (SS) and TN concentrations of 295, 183 and 15 mg/l, respectively resulting in average effluent concentrations of 67 mg COD/l, 17 mg SS/l and 9 mg TN/l. The SBBR systems performed well, and were simple to construct and operate.

Acclimatization studies for degradation of Acid Red 3BN dye and its treatment in moving bed biofilm reactor

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Vijay Kumar ◽  
Akhilesh Khapre ◽  
Chandrakant Thakur ◽  
Parmesh Kumar Chaudhari
Keyword(s):  
Activated Sludge ◽  
Chemical Oxygen Demand ◽  
Oxygen Demand ◽  
Biofilm Reactor ◽  
Moving Bed Biofilm Reactor ◽  
Polymer Carrier ◽  
Fill Ratio ◽  
Moving Bed ◽  
Effluent Flow Rate ◽  
Aerobic Reactor

Abstract In this study, acclimatization of microorganisms for the degradation of Acid Red 3BN dye bearing water (AR3BNDW) using activated sludge was performed in a cylindrical aerobic reactor. The initial value of chemical oxygen demand (COD), dye, and mixed liquor suspended solids (MLSS) of activated sludge were evaluated as 870.5, 80.6 and 1200 mg/L The experiments were performed at ambient temperature (25–35 °C) and the stabilization was achieved at 15 d. Maximum reduction of chemical oxygen demand (COD) and color were observed to be 94.2%, and 91% after 15 d of acclimatization. After completion of acclimatization process, degradation of dye was studied in moving bed biofilm reactor (MBBR). In the process, 38, 50, 68 and 76% color reduction were achieved with polymer carrier fill ratio (FR) of 40, 50, 60 and 70%, respectively in 24 h. For effluent flow rate of 180, 240, 300 and 360 mL/h, respectively, the dye reductions of 76, 60, 48 and 36% and COD reductions of 72, 58, 46 and 34% were achieved in 24 h

Experimental Comparison between Moving Bed Biofilm Reactor (MBBR) and Conventional Activated Sludge (CAS) for River Purification Treatment Plant

2015 ◽  
Vol 1113 ◽  
pp. 806-811 ◽  
Author(s):  
Lariyah Mohd Sidek ◽  
Hairun Aishah Mohiyaden ◽  
Hidayah Basri ◽  
Gasim Hayder Ahmed Salih ◽  
Ahmad Hussein Birima ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Physical Performance ◽  
Removal Efficiency ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Biofilm Reactor ◽  
Moving Bed Biofilm Reactor ◽  
Moving Bed ◽  
Conventional Activated Sludge

Moving Bed Biofilm Reactor (MBBR) systems have been proven as an effective technology for water treatment and have been used for Biochemical Oxygen Demand/Chemical Oxygen Demand (BOD/COD-removal), as well as for nitrification and denitrification in municipal and industrial wastewater treatment. Conventional Activated Sludge (CAS), in particular, has been extensively used in wastewater treatment since decades ago. In this study, physical performance results for both MBBR and CAS were compared and evaluated on laboratory scale basis. The study aims to identify the best system performance in terms of constituent removal efficiency for effective management of the river purification plant. A novel parallel MBBR and CAS pilot plant were fabricated and operated to compare the physical performance of MBBR and CAS. Analysis of the performances for MBBR and CAS show, MBBR has higher COD (85%), AN (75%) and TSS (80%) removal rate compared to CAS COD (53%), AN (53%) and TSS (69%). For BOD removal rate, CAS shows 68% removal rate whereas MBBR shows only 65%. Thus CAS has shown slightly higher removal rate than MBBR. In terms of sludge production, MBBR sludge is less than CAS. Overall performance proves that MBBR has better rate of constituent removal efficiency compared to CAS in the laboratory basis study.

Dairy washwater treatment using a horizontal flow biofilm system

2008 ◽  
Vol 58 (9) ◽  
pp. 1879-1888 ◽  
Author(s):  
E. Clifford ◽  
M. Rodgers ◽  
D. de Paor
Keyword(s):  
Loading Rate ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Dairy Farm ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
Nitrate Contamination ◽  
Horizontal Flow ◽  
Ambient Temperatures ◽  
Economical Alternative

In Ireland, land-spreading is the most widely used method for treating dairy wastewaters. This can be labour intensive and can cause, in some cases, nitrate contamination of groundwater. In this study a simple pilot-scale horizontal flow biofilm reactor (HFBR) with a step-feed was developed and tested at a dairy farm site in County Offaly, Ireland for partial remediation of this soiled water prior to landspreading. During the 122-day study, the top surface plan area (TSPA) hydraulic loading rate was 50 L/m2/day. Influent concentrations averaged: 2904.2 mg total chemical oxygen demand (COD)/L, 950 mg 5-day biochemical oxygen demand (BOD5)/L and 177.9 mg total nitrogen (TN)/L. Between Days 1 and 45 frequent ambient temperatures below 4°C inhibited the build-up of biomass resulting in low removals. From Day 45 the HFBR unit removed 74.9% total COD and 69.6% BOD5, equivalent to TSPA removals of 108.8 g COD/m2/day and 33.1 g BOD5/m2/day. On Sheet 29, by the end of the study, the NH4–N had reduced from 123.1 mg/L in the influent to 37.0 mg/L. TN removal in the reactor averaged 56.0% equating to a TSPA removal rate of 5.0 g TN/m2/day. The HFBR does not require any mechanical aeration, was simple and inexpensive to construct and can provide a robust and economical alternative for the remediation of agricultural soiled water before landspreading.

Sign in / Sign up

Export Citation Format

Share Document