A pilot-scale study on PVA gel beads based integrated fixed film activated sludge (IFAS) plant for municipal wastewater treatment

2015 ◽  
Vol 73 (1) ◽  
pp. 113-123 ◽  
Author(s):  
Nitin Kumar Singh ◽  
Jasdeep Singh ◽  
Aakansha Bhatia ◽  
A. A. Kazmi
Keyword(s):  
Activated Sludge ◽  
Pilot Plant ◽  
Municipal Wastewater ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
16S Rrna Genes ◽  
Volume Index ◽  
Rrna Genes ◽  
Gel Beads

In the present study, a pilot-scale reactor incorporating polyvinyl alcohol gel beads as biomass carrier and operating in biological activated sludge mode (a combination of moving bed biofilm reactor (MBBR) and activated sludge) was investigated for the treatment of actual municipal wastewater. The results, during a monitoring period of 4 months, showed effective removal of chemical oxygen demand (COD), biological oxygen demand (BOD) and NH3-N at optimum conditions with 91%, ∼92% and ∼90% removal efficiencies, respectively. Sludge volume index (SVI) values of activated sludge varied in the range of 25–72 mL/g, indicating appreciable settling characteristics. Furthermore, soluble COD and BOD in the effluent of the pilot plant were reduced to levels well below discharge limits of the Punjab Pollution Control Board, India. A culture dependent method was used to enrich and isolate abundant heterotrophic bacteria in activated sludge. In addition to this, 16S rRNA genes analysis was performed to identify diverse dominant bacterial species in suspended and attached biomass. Results revealed that Escherichia coli, Pseudomonas sp. and Nitrosomonas communis played a significant role in biomass carrier, while Acinetobactor sp. were dominant in activated sludge of the pilot plant. Identification of ciliated protozoa populations rendered six species of ciliates in the plant, among which Vorticella was the most dominant.

Novel biofilm reactor for denitrification of municipal wastewater

2018 ◽  
Vol 78 (7) ◽  
pp. 1566-1575 ◽  
Author(s):  
S. S. Rathnaweera ◽  
B. Rusten ◽  
K. Korczyk ◽  
B. Helland ◽  
E. Rismyhr
Keyword(s):  
Carbon Source ◽  
Municipal Wastewater ◽  
Low Cost ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
Treated Wastewater ◽  
Removal Rates ◽  
Good Filter ◽  
Solids Removal

Abstract A pilot-scale CFIC® (continuous flow intermittent cleaning) reactor was run in anoxic conditions to study denitrification of wastewater. The CFIC process has already proven its capabilities for biological oxygen demand removal with a small footprint, less energy consumption and low cost. The present study focused on the applicability for denitrification. Both pre-denitrification (pre-DN) and post-denitrification (post-DN) were tested. A mixture of primary treated wastewater and nitrified wastewater was used for pre-DN and nitrified wastewater with ethanol as a carbon source was used for post-DN. The pre-DN process was carbon limited and removal rates of only 0.16 to 0.74 g NOx-N/m²-d were obtained. With post-DN and an external carbon source, 0.68 to 2.2 g NO3-Neq/m²-d removal rates were obtained. The carrier bed functioned as a good filter for both the larger particles coming with influent water and the bio-solids produced in the reactor. Total suspended solids removal in the reactor varied from 20% to 78% (average 45%) during post-DN testing period and 9% to 70% (average 29%) for pre-DN. The results showed that the forward flow washing improves both the DN function and filtration ability of the reactor.

scholarly journals Improving and upgrading an existing activated sludge with a compact MBBR – disc filters parallel line for municipal wastewater treatment in touristic alpine areas

2020 ◽  
Vol 15 (2) ◽  
pp. 515-527
Author(s):  
L. Desa ◽  
P. Kängsepp ◽  
L. Quadri ◽  
G. Bellotti ◽  
K. Sørensen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Parallel Line ◽  
Ammonium Nitrogen ◽  
Biofilm Reactor ◽  
Municipal Wastewater Treatment ◽  
Yearly Average

Abstract Many wastewater treatment plants (WWTP) in touristic areas struggle to achieve the effluent requirements due to seasonal variations in population. In alpine areas, the climate also determines a low wastewater temperature, which implies long sludge retention time (SRT) needed for the growth of nitrifying biomass in conventional activated sludge (CAS). Moreover, combined sewers generate high flow and dilution. The present study shows how the treatment efficiency of an existing CAS plant with tertiary treatment can be upgraded by adding a compact line in parallel, consisting of a Moving Bed Biofilm Reactor (MBBR)-coagulation-flocculation-disc filtration. This allows the treatment of influent variations in the MBBR and a constant flow supply to the activated sludge. The performance of the new 2-step process was comparable to that of the improved existing one. Regardless significant variations in flow (10,000–25,000 m3/d) and total suspended solids (TSS) (50–300 mg/L after primary treatment) the effluent quality fulfilled the discharge requirements. Based on yearly average effluent data, TSS were 11 mg/L, chemical oxygen demand (COD) 27 mg/L and total phosphorus (TP) 0.8 mg/L. After the upgrade, ammonium nitrogen (NH4-N) dropped from 4.9 mg/L to 1.3 mg/L and the chemical consumption for phosphorus removal was reduced.

Environmental performance of an integrated fixed-film activated sludge (IFAS) reactor treating actual municipal wastewater during start-up phase

2015 ◽  
Vol 72 (10) ◽  
pp. 1840-1850 ◽  
Author(s):  
Nitin Kumar Singh ◽  
Absar Ahmad Kazmi ◽  
Markus Starkl
Keyword(s):  
Activated Sludge ◽  
Pathogenic Bacteria ◽  
Municipal Wastewater ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Lessons Learned ◽  
Present System ◽  
Salmonella Spp ◽  
Start Up ◽  
Fixed Film

The present study summarizes the start-up performance and lessons learned during the start-up and optimization of a pilot-scale plant employing integrated fixed film activated sludge (IFAS) process treating actual municipal wastewater. A comprehensive start-up was tailored and implemented to cater for all the challenges and problems associated with start-up. After attaining desired suspended biomass (2,000–3,000 mg/L) and sludge age (∼7 days), the average biological oxygen demand (BOD) and chemical oxygen demand (COD) removals were observed as 77.3 and 70.9%, respectively, at optimized conditions, i.e. hydraulic retention time (HRT), 6.9 h; return sludge rate, 160%. The influent concentrations of COD, BOD, total suspended solids, NH3-N, total nitrogen and total phosphorus were found to be in the range of 157–476 mg/L, 115–283 mg/L, 152–428 mg/L, 23.2–49.3 mg/L, 30.1–52 mg/L and 3.6–7.8 mg/L, respectively, and the minimum effluent concentrations were achieved as ∼49 mg/L, 23 mg/L, 35 mg/L, 2.2 mg/L, 3.4 mg/L and 2.8 mg/L, respectively, at optimum state. The present system was found effective in the removal of pathogenic bacteria (Escherichia coli, 79%; Salmonella spp., 97.5%; Shigella spp., 92.9%) as well as coliforms (total coliforms, 97.65%; faecal coliforms, 80.35%) without any disinfection unit. Moreover it was observed that the time required for the stabilization of the plant was approximately 3 weeks if other parameters (sludge age, HRT and dissolved oxygen) are set to optimized values.

Optimization of a mainstream nitritation-denitritation process and anammox polishing

2015 ◽  
Vol 72 (4) ◽  
pp. 632-642 ◽  
Author(s):  
Pusker Regmi ◽  
Becky Holgate ◽  
Dana Fredericks ◽  
Mark W. Miller ◽  
Bernhard Wett ◽  
...  
Keyword(s):  
Retention Time ◽  
Pilot Plant ◽  
Municipal Wastewater ◽  
Ammonia Oxidation ◽  
Inorganic Nitrogen ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
High Rate ◽  
Anammox Bacteria ◽  
Tin Removal

This paper deals with an almost 1-year long pilot study of a nitritation-denitritation process that was followed by anammox polishing. The pilot plant treated real municipal wastewater at ambient temperatures. The effluent of high-rate activated sludge process (hydraulic retention time, HRT = 30 min, solids retention time = 0.25 d) was fed to the pilot plant described in this paper, where a constant temperature of 23 °C was maintained. The nitritation-denitritation process was operated to promote nitrite oxidizing bacteria out-selection in an intermittently aerated reactor. The intermittent aeration pattern was controlled using a strategy based on effluent ammonia and nitrate + nitrite concentrations. The unique feature of this aeration control was that fixed dissolved oxygen set-point was used and the length of aerobic and anoxic durations were changed based on the effluent ammonia and nitrate + nitrite concentrations. The anaerobic ammonia oxidation (anammox) bacteria were adapted in mainstream conditions by allowing the growth on the moving bed bioreactor plastic media in a fully anoxic reactor. The total inorganic nitrogen (TIN) removal performance of the entire system was 75 ± 15% during the study at a modest influent chemical oxygen demand (COD)/NH4+-N ratio of 8.9 ± 1.8 within the HRT range of 3.1–9.4 h. Anammox polishing contributed 11% of overall TIN removal. Therefore, this pilot-scale study demonstrates that application of the proposed nitritation-denitritation system followed by anammox polishing is capable of relatively high nitrogen removal without supplemental carbon and alkalinity at a low HRT.

Occurrence of Microthrix parvicella in sequencing batch reactors

2014 ◽  
Vol 69 (10) ◽  
pp. 1984-1995 ◽  
Author(s):  
Lana Mallouhi ◽  
Ute Austermann-Haun
Keyword(s):  
Activated Sludge ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Oxygen Demand ◽  
Volume Index ◽  
Batch Reactors ◽  
Sequencing Batch Reactors ◽  
Municipal Wastewater Treatment ◽  
Nitrogen And Phosphorus ◽  
Microthrix Parvicella

Sequencing batch reactors (SBRs) are known for high process stability and usually have a good sludge volume index (SVI). Nevertheless, in many SBRs in Germany for municipal wastewater treatment, scum and foam problems can occur, and SVI can be larger than 200 mL/g. The microscopic investigations of the activated sludge from plants with nitrogen and phosphorus removal have shown that Microthrix parvicella is dominant in the activated sludge in most of them. Studies showed that the optimum growth of M. parvicella is performed at a high sludge age (>20 d) and low sludge load in the range of 0.05–0.2 kg of biochemical oxygen demand per kg of total suspended solids per day (kg BOD5/(TSS·d)). The investigations in 13 SBRs with simultaneous aerobic sludge stabilization (most of them are operated with a system called differential internal cycle strategy sequential batch reactor (DIC-SBR)) show that M. parvicella is able to grow in sludge loads less than 0.05 kg BOD5/(kg TSS·d) as well. To optimize the operation of those SBRs, long cycle times (8–12 h) and dosing of iron salts to eliminate long-chain fatty acids are both recommended. This leads to better SVI and keeps M. parvicella at a low frequency.

scholarly journals Polishing of Chemical Oxygen Demand (COD) Using Moving Bed Bio-Reactor

2015 ◽  
Vol 773-774 ◽  
pp. 1281-1285
Author(s):  
Jamal Ali Kawan ◽  
Rakmi Abd-Rahman ◽  
Othman bin Jaafar ◽  
Fatihah Suja
Keyword(s):  
Chemical Oxygen Demand ◽  
Municipal Wastewater ◽  
Removal Rate ◽  
Research Work ◽  
Real Life ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Biofilm Reactor ◽  
Moving Bed ◽  
Building Engineering

The pilot-scale experiment in moving bed biofilm reactor (MBBR) with a capacity of 433 L was carried out for this study with real life situations, it was decided that the complete research work must be done under as realistic conditions as possible,i.e.with real municipal wastewater, chemical free and with local commercially available products such as carriers for biofilm reactor. The reactor was start-up in 30/9/2013 up to date, Effluent from clarifier of STP used as influence of MBBR for polishing. MBBR is using continues down flow to polish effluent municipal wastewater from a faculty of new building engineering community in UKM to get the water free from main pollutant parameters, for reuse in the irrigation or discharge to the river. Laboratory experiments will conduct with different hydraulic retention time (HRT), filling ratio of plastic (Enviro Multi Media) in the MBBR about 5%. Aerobic reactors used the majority of the decaying organic material. An average removal rate of 41.75%, 32.85%, 24.80% and 35.77% of initial chemical oxygen demand (COD) were achieved under a HRT of 24hr, 12hr, 6hr and 2hr, respectively. The model simulated results showed good agreements with experimental results. The model could be employed in the design of a full-scale MBBR process for simultaneous removal of organic carbon from effluent STP.

scholarly journals Community Composition and Function of Bacteria in Activated Sludge of Municipal Wastewater Treatment Plants

Water ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 852 ◽  
Author(s):  
Ning Xie ◽  
Liping Zhong ◽  
Liao Ouyang ◽  
Wang Xu ◽  
Qinghuai Zeng ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Community Structure ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
16S Rrna Genes ◽  
Rrna Genes ◽  
Municipal Wastewater Treatment ◽  
Significant Difference ◽  
Municipal Wastewater Treatment Plants

Municipal wastewater treatment plants (WWTPs) use functional microorganisms in activated sludge (AS) to reduce the environmental threat posed by wastewater. In this study, Illumina NovaSeq sequencing of 16S rRNA genes was performed to explore the microbial communities of AS at different stages of the two WWTP projects in Shenzhen, China. Results showed that Proteobacteria, Bacteroidetes, Acidobacteria, Firmicutes, and Nitrospirae were the dominant phyla in all the samples, with Proteobacteria being the most abundant and reaching a maximum proportion of 59.63%. There was no significant difference in biodiversity between the two water plants, but Stage 1 and Stage 2 were significantly different. The Mantel test indicated that nitrate, total nitrogen (TN), chemical oxygen demand (COD), and nutrients were essential factors affecting the bacterial community structure. FAPROTAX analysis emphasized that the leading functional gene families include nitrification, aerobic nitrite oxidation, human pathogens, and phototrophy. This study reveals changes in the community structure of AS in different treatment units of Banxuegang WWTP, which can help engineers to optimize the wastewater treatment process.

Pumped flow biofilm reactors (PFBR) for treating municipal wastewater

2008 ◽  
Vol 57 (12) ◽  
pp. 1857-1865 ◽  
Author(s):  
E. O'Reilly ◽  
M. Rodgers ◽  
X.-M. Zhan
Keyword(s):  
Wastewater Treatment ◽  
Surface Area ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Cross Flow ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Ammonium Nitrogen ◽  
Biofilm Reactor ◽  
Bench Scale

A novel laboratory bench-scale sequencing batch biofilm reactor (SBBR) system was developed for the treatment of synthetic domestic strength wastewater, comprising two side-by-side 18 l reactor tanks, each containing a plastic biofilm media module. Aerobic and anoxic conditions in the biofilms were effected by intermittent alternate pumping of wastewater between the two reactors. With a media surface area loading rate of 4.2 g chemical oxygen demand (COD)/m2.d, the average influent COD, total nitrogen (TN) and ammonium-nitrogen (NH4-N) concentrations of 1021 mg/l, 97 mg/l and 54 mg/l, respectively, reduced to average effluent concentrations of 72 mg COD/l, 17.8 mg TN/l, and 5.5 mg NH4-N /l. Using a similar alternating biofilm exposure arrangement, a 16 person equivalent pilot (PE) plant was constructed at a local village treatment works to remove organic carbon from highly variable settled municipal wastewater and comprised two reactors, one positioned above the other, each containing a module of cross-flow plastic media with a surface area of 100 m2. Two different pumping sequences (PS) in the aerobic phase were examined where the average influent COD concentrations were 220 and 237 mg/l for PS1 and PS2, respectively, and the final average effluent COD was consistently less than 125 mg/l – the European Urban Wastewater Treatment Directive limit – with the best performance occurring in PS1. Nitrification was evident during both PS1 and PS2 studies. A 300 PE package treatment plant was designed based on the bench-scale and pilot-scale studies, located at a local wastewater treatment works and treated municipal influent with average COD, suspended solids (SS) and TN concentrations of 295, 183 and 15 mg/l, respectively resulting in average effluent concentrations of 67 mg COD/l, 17 mg SS/l and 9 mg TN/l. The SBBR systems performed well, and were simple to construct and operate.

Linking floc structure and settling properties to activated sludge population dynamics in an SBR

2003 ◽  
Vol 47 (12) ◽  
pp. 9-18 ◽  
Author(s):  
R. Govoreanu ◽  
D. Seghers ◽  
I. Nopens ◽  
B. De Clercq ◽  
H. Saveyn ◽  
...  
Keyword(s):  
Microbial Community ◽  
Activated Sludge ◽  
Size Distribution ◽  
Community Dynamics ◽  
16S Rrna Genes ◽  
Volume Index ◽  
Rrna Genes ◽  
Filamentous Bacteria ◽  
Floc Size ◽  
Stable Conditions

Over a period of 227 days properties of activated sludge grown in an aequencing batch reactor (SBR) operated under stable conditions were analyzed. Settling properties (sludge volume index (SVI)) of the activated sludge were compared with on-line measurements of floc size and size distribution obtained by using a laser light scattering technique (Malvern Mastersizer/S, Malvern, UK), and with measurements of microbial community dynamics analyzed by denaturing gradient gel electrophoresis (DGGE) patterns of 16S rRNA genes. In addition, microscopical observations were used to confirm the results. Three distinct stages in the SBR evolution were observed. In the first stage the structural floc properties showed predominant presence of floc-forming bacteria in the activated sludge. A good correlation between floc size, settling properties and microbial community evolution was observed. The second stage showed a good balance between floc-forming and filamentous bacteria, with good settling properties and a highly dynamic community in the SBR. In the third stage, an increase in the filamentous bacteria, which became predominant in the system was observed. Again, a good correlation between settling properties and floc size distribution was obtained and a new dominant species was observed in the DGGE patterns, which can be assumed to be a filamentous organism.

Enhancing nitrogen removal efficiency in a dyestuff wastewater treatment plant with the IFFAS process: the pilot-scale and full-scale studies

2017 ◽  
Vol 77 (1) ◽  
pp. 70-78 ◽  
Author(s):  
Yanjun Mao ◽  
Xie Quan ◽  
Huimin Zhao ◽  
Yaobin Zhang ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Full Scale ◽  
Nitrification And Denitrification ◽  
Dyestuff Wastewater

Abstract The activated sludge (AS) process is widely applied in dyestuff wastewater treatment plants (WWTPs); however, the nitrogen removal efficiency is relatively low and the effluent does not meet the indirect discharge standards before being discharged into the industrial park's WWTP. Hence it is necessary to upgrade the WWTP with more advanced technologies. Moving bed biofilm processes with suspended carriers in an aerobic tank are promising methods due to enhanced nitrification and denitrification. Herein, a pilot-scale integrated free-floating biofilm and activated sludge (IFFAS) process was employed to investigate the feasibility of enhancing nitrogen removal efficiency at different hydraulic retention times (HRTs). The results showed that the effluent chemical oxygen demand (COD), ammonium nitrate (NH4+-N) and total nitrogen (TN) concentrations of the IFFAS process were significantly lower than those of the AS process, and could meet the indirect discharge standards. PCR-DGGE and FISH results indicated that more nitrifiers and denitrifiers co-existed in the IFFAS system, promoting simultaneous nitrification and denitrification. Based on the pilot results, the IFFAS process was used to upgrade the full-scale AS process, and the effluent COD, NH4+-N and TN of the IFFAS process were 91–291 mg/L, 10.6–28.7 mg/L and 18.9–48.6 mg/L, stably meeting the indirect discharge standards and demonstrating the advantages of IFFAS in dyestuff wastewater treatment.

Sign in / Sign up

Export Citation Format

Share Document