Pressure Generated from Head Garment with Padding Insert Used for Hypertrophic Scar Treatment

2015 ◽  
Vol 815 ◽  
pp. 282-286
Author(s):  
A.F. Aiman ◽  
M.N. Salleh ◽  
K.A. Ismail
Keyword(s):  
Pressure Distribution ◽  
Cross Sections ◽  
3D Modeling ◽  
Hypertrophic Scar ◽  
Pressure Range ◽  
Burn Injury ◽  
Reduction Factor ◽  
Modeling Software ◽  
Facial Area ◽  
Non Surgical Treatment

Pressure garment is a standard non-surgical treatment for hypertrophic scar caused by burn injury. However, the main problem identified was the non-uniform pressure distribution due to the complexity of the contour at the facial area. Therefore, padding was developed to produce more efficient pressure distribution. This study used 3D scanning apparatus to obtain the cross sections of the facial area. The padding was developed using 3D modeling software which act as an insert to fill the gaps at the contact area of the garment and facial areas. The result shows that by inserting the padding underneath the garment, the pressure outputs indicate an acceptable pressure range with the suitable reduction factor for the head garment fabrication.

34 Rete Ridges are Decreased in Dyschromic Burn Hypertrophic Scar: A Histological Study

2021 ◽  
Vol 42 (Supplement_1) ◽  
pp. S27-S27
Author(s):  
Bonnie C Carney ◽  
Taryn E Travis ◽  
Romina Deldar ◽  
Lauren T Moffatt ◽  
Laura S Johnson ◽  
...  
Keyword(s):  
Basement Membrane ◽  
Hypertrophic Scar ◽  
Burn Injury ◽  
Histological Study ◽  
Normal Skin ◽  
Weak Correlation ◽  
Rete Ridge ◽  
Skin Physiology ◽  
Predominantly Female ◽  
Injured Skin

Abstract Introduction Dyschromic hypertrophic scar (HTS) with areas of hyper- and hypo-pigmentation is a common sequelae of burn injury. The mechanism behind the development of dyschromia has not been elucidated. In this study, we provide a histological analysis of these scars with a focus on rete ridge presence. Rete ridges occur in epithelial tissues such as oral mucosa and skin and can be described as undulating “pegs” that are interdigitated with dermal papillae. Rete ridges enhance adhesion of the epidermis to the dermis. We hypothesize that rete ridge presence is important for normal skin physiology, and their absence or presence may hold mechanistic significance in post-burn HTS dyschromia. Methods Subjects with post-burn dyschromic HTS were consented and enrolled (n=27). Punch biopsies of hyper-, hypo-, and normally pigmented scar and skin were collected and stored in formalin. Biopsies were paraffin embedded, sectioned, stained with H&E, and imaged. The number of rete ridges were investigated by calculating a rete ridge ratio from the length of the basement membrane and the length of the epidermis. Results The patient population was predominantly female (55.5%), black (70.4%), and had Fitzpatrick skin Type V (51.9%). The injuries were primarily as a result of flame (37%) and scald (33.3%) and resulted in a median TBSA burn of 7%. The median age of the scar at the time of sample acquisition was 12.2 months. The rete ridge ratio of normally pigmented, un-injured skin was above 1 (1.31 ± 0.04), indicating that normal skin’s basement membrane is longer than its epidermal length due to the presence of rete ridges. HTSs resulting from burn wounds that healed without split thickness autografts were first investigated. The number of rete ridges was higher in normal skin compared to HTS that was either hypo- or hyperpigmented (1.31 ± 0.04 vs. 1.13 ± 0.05 and 1.14 ± 0.04 vs, p< 0.05). This difference was similar despite pigmentation phenotype. When hyper-pigmented scars resulting from wounds that were treated with split thickness autografts (Hyper(+)) were investigated, rete ridge number was significantly higher than in Hyper(-) (1.89 ± 0.23, p< 0.01). Patient age showed a weak correlation (R=-0.33) with rete ridge ratio where older patients had lower rete ridge ratios in normal, un-injured skin. Hyper(+) showed a weak correlation between rete ridge ratio and age of scar (R=-0.38). Conclusions Post-burn HTS that is dyschromic has fewer rete ridges than normal skin. This finding may explain the decreased epidermal barrier function that is associated with HTS.

Determination of critical loads for global buckling of axially loaded pultruded fiber-reinforced polymer members with doubly symmetric cross sections

2018 ◽  
Vol 21 (12) ◽  
pp. 1911-1922
Author(s):  
Yang Zhan ◽  
Gang Wu
Keyword(s):  
Closed Form ◽  
Cross Sections ◽  
Reduction Factor ◽  
Fiber Reinforced Polymer ◽  
Design Stage ◽  
Fiber Reinforced ◽  
Original Solution ◽  
Form Equation ◽  
Reinforced Polymer ◽  
Global Buckling

This article proposes a new closed-form equation to determine the reduction factor for global buckling of concentrically loaded pultruded fiber-reinforced polymer struts based on the Ayrton–Perry formula and observed initial out-of-straightness of pultruded fiber-reinforced polymer members measured by other researchers, which makes the original solution recommended by Eurocode 3 easy to be used to predict the global buckling loads of doubly symmetric pultruded fiber-reinforced polymer members subjected to axial compression. The influence of the geometric imperfections of pultruded fiber-reinforced polymer profiles is considered in this new closed-form equation. Validation of the solution including the parameter of the reduction factor for global buckling of pultruded fiber-reinforced polymer columns is performed by comparison with published experimental evidence. In addition, compared with the five closed-form solutions available in the literature, this solution exhibits higher accuracy in predicting the global buckling capacity of concentrically loaded pultruded fiber-reinforced polymer struts with doubly symmetric cross sections. The solution implemented into the new reduction factor equation for global buckling of pultruded fiber-reinforced polymer members can be conveniently used by structural engineers at the preliminary engineering design stage for accurately assessing the reliability and safety of composite structures under concentric compressive loading.

scholarly journals Dynamic modeling of tunnel survey spatiotemporal data

2014 ◽  
Vol 20 (2) ◽  
pp. 354-375
Author(s):  
Xiaolong Li ◽  
Jiansi Yang ◽  
Bingxuan Guo ◽  
Hua Liu ◽  
Jun Hua
Keyword(s):  
Survey Data ◽  
Cross Section ◽  
Cross Sections ◽  
3D Modeling ◽  
3D Model ◽  
Three Dimensional ◽  
Spatiotemporal Data ◽  
Excavation Process ◽  
Special Cases ◽  
Time Stamps

Currently, for tunnels, the design centerline and design cross-section with time stamps are used for dynamic three-dimensional (3D) modeling. However, this approach cannot correctly reflect some qualities of tunneling or some special cases, such as landslips. Therefore, a dynamic 3D model of a tunnel based on spatiotemporal data from survey cross-sections is proposed in this paper. This model can not only playback the excavation process but also reflect qualities of a project typically missed. In this paper, a new conceptual model for dynamic 3D modeling of tunneling survey data is introduced. Some specific solutions are proposed using key corresponding technologies for coordinate transformation of cross-sections from linear engineering coordinates to global projection coordinates, data structure of files and database, and dynamic 3D modeling. A 3D tunnel TIN model was proposed using the optimized minimum direction angle algorithm. The last section implements the construction of a survey data collection, acquisition, and dynamic simulation system, which verifies the feasibility and practicality of this modeling method.

Main Structure Design on Dual-Purpose Move-Assistant Device of Wheelchair and Crutch on SolidWorks

2012 ◽  
Vol 482-484 ◽  
pp. 2148-2152
Author(s):  
Cong Wei Yang ◽  
Hai Tao Wu ◽  
Hong Bin Liu
Keyword(s):  
3D Modeling ◽  
3D Model ◽  
Structure Design ◽  
Model Design ◽  
Work Time ◽  
Dual Purpose ◽  
Main Structure ◽  
Modeling Software ◽  
Design Requirements

Established the model of dual-purpose move-assistant device of wheelchair and crutch, using 3D modeling software SolidWorks, finished the 3D model of parts and parts assembly according to the design requirements of dual-purpose move-assistant device of wheelchair and crutch. Verified the accuracy of designing the project. With the software to carry on a 3D model design can save work time and economize the design budget, providing the theoretical feasibility of realizing the dual-purpose move-assistant device of wheelchair and crutch.

scholarly journals A New Diagnostic Approach for Periprosthetic Acetabular Fractures Based on 3D Modeling: A Study Protocol

Diagnostics ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 15 ◽  
Author(s):  
Giuseppe Marongiu ◽  
Roberto Prost ◽  
Antonio Capone
Keyword(s):  
Bone Quality ◽  
3D Modeling ◽  
Surgical Simulation ◽  
Articular Surface ◽  
Real Life ◽  
Diagnostic Process ◽  
Acetabular Fractures ◽  
Loss Assessment ◽  
Metal Artifacts ◽  
Modeling Software

Periprosthetic acetabular fractures after total hip arthroplasty (THA) are mostly related to low energy trauma reduced bone quality. CT-scan is widely used to evaluate acetabular fractures, however, metal artifacts produced prosthetic implants limit the visualization of the articular surface and bone loss assessment. 3D modeling software allows us to creating tridimensional images of the bony surface, removing the metallic implants trough image segmentation. We highlight the use of 3D modeling and rapid prototyping (3D printing) for the diagnostic process of periprosthetic acetabular fracture around THA. 3D modeling software was used to improve the assessment of fracture morphology and bone quality. Moreover, the 3D images were printed in a real-life size model and used for preoperative implant templating, sizing and surgical simulation.

scholarly journals The Accuracy of Digital Face Scans Obtained from 3D Scanners: An In Vitro Study

2019 ◽  
Vol 16 (24) ◽  
pp. 5061 ◽  
Author(s):  
Pokpong Amornvit ◽  
Sasiwimol Sanohkan
Keyword(s):  
3D Modeling ◽  
In Vitro Study ◽  
Reference Points ◽  
Vitro Study ◽  
Washington Dc ◽  
Practical Applications ◽  
Face Scanning ◽  
Modeling Software ◽  
The Face

Face scanners promise wide applications in medicine and dentistry, including facial recognition, capturing facial emotions, facial cosmetic planning and surgery, and maxillofacial rehabilitation. Higher accuracy improves the quality of the data recorded from the face scanner, which ultimately, will improve the outcome. Although there are various face scanners available on the market, there is no evidence of a suitable face scanner for practical applications. The aim of this in vitro study was to analyze the face scans obtained from four scanners; EinScan Pro (EP), EinScan Pro 2X Plus (EP+) (Shining 3D Tech. Co., Ltd. Hangzhou, China), iPhone X (IPX) (Apple Store, Cupertino, CA, USA), and Planmeca ProMax 3D Mid (PM) (Planmeca USA, Inc. IL, USA), and to compare scans obtained from various scanners with the control (measured from Vernier caliper). This should help to identify the appropriate scanner for face scanning. A master face model was created and printed from polylactic acid using the resolution of 200 microns on x, y, and z axes and designed in Rhinoceros 3D modeling software (Rhino, Robert McNeel and Associates for Windows, Washington DC, USA). The face models were 3D scanned with four scanners, five times, according to the manufacturer’s recommendations; EinScan Pro (Shining 3D Tech. Co., Ltd. Hangzhou, China), EinScan Pro 2X Plus (Shining 3D Tech. Co., Ltd. Hangzhou, China) using Shining Software, iPhone X (Apple Store, Cupertino, CA, USA) using Bellus3D Face Application (Bellus3D, version 1.6.2, Bellus3D, Inc. Campbell, CA, USA), and Planmeca ProMax 3D Mid (PM) (Planmeca USA, Inc. IL, USA). Scan data files were saved as stereolithography (STL) files for the measurements. From the STL files, digital face models are created in the computer using Rhinoceros 3D modeling software (Rhino, Robert McNeel and Associates for Windows, Washington DC, USA). Various measurements were measured five times from the reference points in three axes (x, y, and z) using a digital Vernier caliper (VC) (Mitutoyo 150 mm Digital Caliper, Mitutoyo Co., Kanagawa, Japan), and the mean was calculated, which was used as the control. Measurements were measured on the digital face models of EP, EP+, IPX, and PM using Rhinoceros 3D modeling software (Rhino, Robert McNeel and Associates for Windows, Washington DC, USA). The descriptive statistics were done from SPSS version 20 (IBM Company, Chicago, USA). One-way ANOVA with post hoc using Scheffe was done to analyze the differences between the control and the scans (EP, EP+, IPX, and PM). The significance level was set at p = 0.05. EP+ showed the highest accuracy. EP showed medium accuracy and some lesser accuracy (accurate until 10 mm of length), but IPX and PM showed the least accuracy. EP+ showed accuracy in measuring the 2 mm of depth (diameter 6 mm). All other scanners (EP, IPX, and PM) showed less accuracy in measuring depth. Finally, the accuracy of an optical scan is dependent on the technology used by each scanner. It is recommended to use EP+ for face scanning.

Design and Research of Synchronous-Style Clamping Mechanism for Cable-Detecting Robot

2014 ◽  
Vol 1028 ◽  
pp. 127-133
Author(s):  
Bing Hui Wu ◽  
Jian Jun Xi
Keyword(s):  
3D Modeling ◽  
Design Criterion ◽  
Velocity Curve ◽  
Displacement Curve ◽  
Robot Design ◽  
Clamping Force ◽  
Broad Application ◽  
Labor Practices ◽  
Modeling Software ◽  
Application Prospects

Cable-detecting robot can replace human to accomplish various dangerous works. Comparing with labor practices, the robot not only reduce costs greatly but also guarantee the safety of workers. Thus, it is of broad application prospects. To assure the reliable action of the robot on the rope, a synchronous-style plane for clamping mechanism was proposed in this paper. According to the operation requirements of the robot, design criterion of clamping-force of this lock-mechanism was prompted. Utilizing 3D modeling software Pro/E, simulation model of synchronous clamping mechanism was built. And then displacement curve, velocity curve and acceleration curve will be obtained from the clamping mechanism output.

scholarly journals Optimization of the Infrastructure of Reinforced Concrete Reservoirs by a Particle Swarm Algorithm

2015 ◽  
Vol 23 (1) ◽  
pp. 14-22 ◽  
Author(s):  
Saeed Kia ◽  
Mohammad Hassan Sebt ◽  
Vahid Shahhosseini
Keyword(s):  
Reinforced Concrete ◽  
Cross Sections ◽  
Linear Models ◽  
Particle Swarm ◽  
Pso Algorithm ◽  
Optimization Techniques ◽  
Particle Swarm Algorithm ◽  
Construction Costs ◽  
Related Information ◽  
Modeling Software

Abstract Optimization techniques may be effective in finding the best modeling and shapes for reinforced concrete reservoirs (RCR) to improve their durability and mechanical behavior, particularly for avoiding or reducing the bending moments in these structures. RCRs are one of the major structures applied for reserving fluids to be used in drinking water networks. Usually, these structures have fixed shapes which are designed and calculated based on input discharges, the conditions of the structure's topology, and geotechnical locations with various combinations of static and dynamic loads. In this research, the elements of reservoir walls are first typed according to the performance analyzed; then the range of the membrane based on the thickness and the minimum and maximum cross sections of the bar used are determined in each element. This is done by considering the variable constraints, which are estimated by the maximum stress capacity. In the next phase, based on the reservoir analysis and using the algorithm of the PARIS connector, the related information is combined with the code for the PSO algorithm, i.e., an algorithm for a swarming search, to determine the optimum thickness of the cross sections for the reservoir membrane’s elements and the optimum cross section of the bar used. Based on very complex mathematical linear models for the correct embedding and angles related to achain of peripheral strengthening membranes, which optimize the vibration of the structure, a mutual relation is selected between the modeling software and the code for a particle swarm optimization algorithm. Finally, the comparative weight of the concrete reservoir optimized by the peripheral strengthening membrane is analyzed using common methods. This analysis shows a 19% decrease in the bar’s weight, a 20% decrease in the concrete’s weight, and a minimum 13% saving in construction costs according to the items of a checklist for a concrete reservoir at 10,000 m3.

Study on Parametric Reverse Modeling

2014 ◽  
Vol 721 ◽  
pp. 230-233
Author(s):  
Shuang Xi Hu
Keyword(s):  
Reverse Engineering ◽  
3D Modeling ◽  
Point Clouds ◽  
Hybrid Modeling ◽  
Design Intent ◽  
Engineering Software ◽  
Modeling Software

Methods about parametric reverse modeling have been studied based on products’ point clouds by comparing model rebuilding processes in different ways, such as collaborative reconstruction based on both reverse engineering software Geomagic and 3D modeling software, reverse and forward hybrid modeling based on Rapidform. It‘s concluded that reverse and forward hybrid modeling based on Rapidform takes more advantages in parametric reverse modeling, It is more rapid , accurate, and closer to the design intent.

Sign in / Sign up

Export Citation Format

Share Document