Hot Deformation Behaviors of SiCp/Al Composites

2014 ◽  
Vol 1058 ◽  
pp. 165-169 ◽  
Author(s):  
Shi Ming Hao ◽  
Jing Pei Xie
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
True Strain ◽  
Constant Strain Rate ◽  
Hot Compression ◽  
Compression Tests ◽  
Sensitive Material ◽  
2024 Aluminum Alloy ◽  
Deformation Behaviors

The hot deformation behaviors of 30%SiCp/2024 aluminum alloy composites was studied by hot compression tests using Gleeble-1500 thermomechanical simulator at temperatures ranging from 350-500°C under strain rates of 0.01-10 s-1. The true stress-true strain curves were obtained in the tests. Constitutive equation and processing map were established. The results show that the flow stress decreases with the increase of deformation temperature at a constant strain rate, and increases with the increase of strain rate at constant temperature, indicating that composite is a positive strain rate sensitive material. The flow stress behavior of composite during hot compression deformation can be represented by a Zener-Hollomon parameter in the hyperbolic sine form. Its activation energy for hot deformation Q is 183.251 kJ/mol. The optimum hot working conditions for this material are suggested.

Hot Deformation Behaviors of SiCp/2024 Aluminum Composites

2013 ◽  
Vol 833 ◽  
pp. 271-275
Author(s):  
Shi Ming Hao ◽  
Jing Pei Xie
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
True Strain ◽  
Constant Strain Rate ◽  
Hot Compression ◽  
Compression Tests ◽  
Sensitive Material ◽  
2024 Aluminum Alloy ◽  
Deformation Behaviors

The hot deformation behaviors of 30%SiCp/2024 aluminum alloy composites was studied by hot compression tests using Gleeble-1500 thermomechanical simulator at temperatures ranging from 350-500 °C under strain rates of 0.01-10 s-1. The true stress-true strain curves were obtained in the tests. Constitutive equation and processing map were established. The results show that the flow stress decreases with the increase of deformation temperature at a constant strain rate, and increases with the increase of strain rate at constant temperature, indicating that composite is a positive strain rate sensitive material. The flow stress behavior of composite during hot compression deformation can be represented by a Zener-Hollomon parameter in the hyperbolic sine form. Its activation energy for hot deformation Q is 153.251 kJ/mol. The optimum hot working conditions for this material are suggested.

scholarly journals Constitutive Behavior of an AA4032 Piston Alloy with Cu and Er Additions upon High-Temperature Compressive Deformation

2019 ◽  
Vol 51 (1) ◽  
pp. 467-481
Author(s):  
Suwaree Chankitmunkong ◽  
Dmitry G. Eskin ◽  
Chaowalit Limmaneevichitr
Keyword(s):  
Activation Energy ◽  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
Base Alloy ◽  
True Strain ◽  
Constitutive Behavior ◽  
Compression Tests ◽  
Primary Si ◽  
Constitutive Parameters

Abstract Aluminum piston alloys of the AA4032 type are produced by direct-chill (DC) casting and subsequent forging; therefore, it is important to understand their thermomechanical behavior. In recent years, it was shown that additions of Cu and Er could improve mechanical properties of these alloys at room and high temperatures. In this work, we studied the constitutive behavior of AA4032-type alloys with and without Cu and Er additions. The experimental true stress–true strain curves were obtained by compression tests under various temperatures [683 K to 723 K (410 °C to 450 °C)] and strain rates (0.01 to 10 s−1) to determine constitutive parameters [strain-rate sensitivity, activation energy, and Zener–Hollomon (Z) parameter] for the hot deformation behavior of AA4032-type piston alloys with and without additions of Cu and Er. The flow stress decreased with increasing deformation temperature and decreasing strain rate. The results also showed that increasing the Cu content increased the flow stress over the applied range of deformation conditions due to solid-solution strengthening and the formation of primary Si particles, which led to an increase in the activation energy during hot deformation. Moreover, the main microstructural damage in the AA4032 alloy with 3.5 pct Cu was predominantly due to the cracking of primary Si particles. Additions of 0.4 pct Er and 3.5 pct Cu lower the activation energy of deformation, Q, as compared to the base alloy and the alloy with 3.5 pct Cu. The microstructures in the deformed specimens consisted of subgrains, recrystallized grains, and fine eutectic phases. The alloys containing Er demonstrated more polygonized grains at a low strain rate than the alloys without Er, indicating that Er hindered recrystallization development. The peak stress of the AA4032 alloy with 3.5 pct Cu alloy was higher than for the base AA4032 alloy and for the AA4032 alloy with 3.5 pct Cu and 0.4 pct Er additions, which was attributed to the prevalence of the work-hardening mechanism over the softening mechanism.

scholarly journals Hot deformation behavior of TC18 titanium alloy

2013 ◽  
Vol 17 (5) ◽  
pp. 1523-1528
Author(s):  
Bao-Hua Jia ◽  
Wei-Dong Song ◽  
Hui-Ping Tang ◽  
Jian-Guo Ning
Keyword(s):  
Titanium Alloy ◽  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
True Strain ◽  
Testing Machine ◽  
Constitutive Relationship ◽  
Compression Tests ◽  
Hot Deformation Behavior

Isothermal compression tests of TC18 titanium alloy at the deformation temperatures ranging from 25?C to 800?C and strain rate ranging from 10-4 to 10-2 s-1 were conducted by using a WDW-300 electronic universal testing machine. The hot deformation behavior of TC18 was characterized based on an analysis of the true stress-true strain curves of TC18 titanium alloy. The curves show that the flow stress increases with increasing the strain rate and decreases with increasing the temperature, and the strain rate play an important role in the flow stress when increasing the temperatures. By taking the effect of strain into account, an improved constitutive relationship was proposed based on the Arrhenius equation. By comparison with the experimental results, the model prediction agreed well with the experimental data, which demonstrated the established constitutive relationship was reliable and can be used to predict the hot deformation behavior of TC18 titanium alloy.

Hot Deformation and Processing Map of C919 Aluminum Alloy

2015 ◽  
Vol 816 ◽  
pp. 810-817
Author(s):  
Yong Biao Yang ◽  
Zhi Min Zhang ◽  
Xing Zhang
Keyword(s):  
Aluminum Alloy ◽  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
Testing Machine ◽  
Strain Rate Range ◽  
Hot Compression ◽  
Strain Rates ◽  
Processing Maps ◽  
Compression Tests

The hot deformation behaviors of Aluminum alloy C919 were studied in the present investigation. The hot compression tests for C919 were carried out in the temperature range of 350°C~470°C and strain rates range of 0.001s-1~1s-1 using GLEEBLE-1500 thermal simulate testing machine. Optical microscopy (OM) was used for the microstructure characterization. The experimental results showed that the flow stress of C919 aluminum alloy decreased with increasing temperature and decreasing strain rates and the flow stress curves tended to increase at a strain rate of 1s-1 with increasing strain, while the flow stresses kept with increasing strain at lower strain rate. The alloys were more prone to dynamic recrystallization with decreasing strain rates during hot deformation. The hot compression behavior of C919 aluminum alloy can be described as hyperbolic sine function corrected Arrhenius relation. The processing maps for the alloy were built at a strain of 0.6. The instability deformation domain occurred at temperatures range from 350°C and 380°C and at a strain rate of 0.1-1s-1. Based on the processing maps and microstructure observations, the optimum hot-working parameters were determined to be at a temperature of 470°C in the strain rate range from 0.1-0.01s−1 for the C919 aluminum alloy.

scholarly journals Flow Stress and Hot Deformation Activation Energy of 6082 Aluminium Alloy Influenced by Initial Structural State

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1248 ◽  
Author(s):  
Ivo Schindler ◽  
Petr Kawulok ◽  
Vladivoj Očenášek ◽  
Petr Opěla ◽  
Rostislav Kawulok ◽  
...  
Keyword(s):  
Activation Energy ◽  
Flow Stress ◽  
Strain Rate ◽  
Aluminium Alloy ◽  
Hot Deformation ◽  
True Strain ◽  
Initial Structure ◽  
Compression Tests ◽  
Deformation Activation Energy ◽  
Q Values

Stress-strain curves of the EN AW 6082 aluminium alloy with 1.2 Si-0.51 Mg-0.75 Mn (wt.%) were determined by the uniaxial compression tests at temperatures of 450–550 °C with a strain rate of 0.5–10 s−1. The initial structure state corresponded to three processing types: as-cast structure non-homogenized or homogenized at 500 °C, and the structure after homogenization and hot extrusion. Significantly higher flow stress appeared as a result of low temperature forming of the non-homogenized material. Hot deformation activation energy Q-values varied between 99 and 122 kJ·mol−1 for both homogenized materials and from 200 to 216 kJ·mol−1 for the as-cast state, while the Q-values calculated from the measured steady-state stress were always higher than those calculated from the peak stress values. For the extruded state of the 6082 alloy, the physically-based model was developed to reliably predict the flow stress influenced by dynamic softening, temperature, strain rate, and true strain up to 0.6.

scholarly journals Hot Deformation Behaviour of Mn–Cr–Mo Low-Alloy Steel in Various Phase Regions

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1255 ◽  
Author(s):  
Ivo Schindler ◽  
Petr Opěla ◽  
Petr Kawulok ◽  
Jaroslav Sojka ◽  
Kateřina Konečná ◽  
...  
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behaviour ◽  
True Strain ◽  
Coarse Grained ◽  
Peak Strain ◽  
Compression Tests ◽  
Wide Range ◽  
Hot Deformation Behaviour

The deformation behaviour of a coarse-grained as-cast medium-carbon steel, alloyed with 1.2% Mn, 0.8% Cr and 0.2% Mo, was studied by uniaxial compression tests for the strain rates of 0.02 s−1–20 s−1 in the unusually wide range of temperatures (650–1280 °C), i.e., in various phase regions including the region with predominant bainite content (up to the temperature of 757 °C). At temperatures above 820 °C, the structure was fully austenitic. The hot deformation activation energies of 648 kJ·mol−1 and 364 kJ·mol−1 have been calculated for the temperatures ≤770 °C and ≥770 °C, respectively. This corresponds to the significant increase of flow stress in the low-temperature bainitic region. Unique information on the hot deformation behaviour of bainite was obtained. The shape of the stress-strain curves was influenced by the dynamic recrystallization of ferrite or austenite. Dynamically recrystallized austenitic grains were strongly coarsened with decreasing strain rate and growing temperature. For the austenitic region, the relationship between the peak strain and the Zener–Hollomon parameter has been derived, and the phenomenological constitutive model describing the flow stress depending on temperature, true strain rate and true strain was developed. The model can be used to predict the forming forces in the seamless tubes production of the given steel.

Flow and Densification Behaviors of Sintered P/F-10C50 Steel under Hot Compression

2016 ◽  
Vol 849 ◽  
pp. 811-818
Author(s):  
Biao Guo ◽  
Chang Chun Ge ◽  
Yi Xu ◽  
Qiu Yan Lu ◽  
Sui Cai Zhang
Keyword(s):  
Constitutive Equation ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Temperature ◽  
Hot Compression ◽  
Compression Tests ◽  
Sintered Steel ◽  
Absolute Relative Error ◽  
Average Absolute Relative Error ◽  
Deformation Behaviors

The hot deformation and densification behaviors of sintered P/F-10C50 steel were investigated by hot compression tests on Gleeble-1500 thermal mechanical simulator at the temperature ranging from 900 °C to 1000 °C and the strain rate ranging from 0.1 s-1 to 10 s-1. The flow and densification characteristics of the tested specimens at different deformation temperatures and strain rates were studied. The flow stress of the sintered steel persistently increases until the end of the test as the result of matrix and geometric work hardening. The higher deformation temperature and strain rate are conductive to the healing of the pores and promote the densification of the sintered steel, while the higher deformation temperature and lower strain rate impede the densification. The constitutive equation of the sintered steel is established by the means of stepwise regression. The flow stresses predicted by the established constitutive equation are in good agreement with the experimental values, and the correlation coefficient (R) and the average absolute relative error (AARE) are 0.9931 and 3.52%, respectively. These results demonstrate the hot deformation behaviors of the sintered P/F-10C50 steel are excellently predicted by the established constitutive equation.

Hot Deformation Studies of a Low Carbon Steel Containing V

2013 ◽  
Vol 554-557 ◽  
pp. 1224-1231 ◽  
Author(s):  
Cecilia Poletti ◽  
Martina Dikovits ◽  
Javier Ruete
Keyword(s):  
Strain Rate ◽  
Hot Deformation ◽  
Flow Instability ◽  
True Strain ◽  
Low Carbon Steel ◽  
Dynamic Effect ◽  
Rate Sensitivity ◽  
Low Carbon ◽  
Compression Tests ◽  
Deformation Parameters

Low alloyed steels produced by continuous casting are thermomechanically treated to achieve final high mechanical properties, meaning a good combination of strength and toughness. The hot deformation mechanisms of a micro-alloyed steel containing up to 0.1wt% of V is studied by means of hot compression tests using a Gleeble®3800 device. Austenitization of samples is carried out at 1150°C during 2 minutes followed by cooling to the deformation temperature at 1Ks-1in the range of 750 – 1150°C. The studied strain rate range is from 0.01 to 80 s-1and the total true strain achieved is of 0.7. In situ water quenching is applied after the deformation to freeze the microstructure and avoid any post dynamic effect. The Ar3temperature is determined by dilatometry experiments to be 725°C for the used cooling rate. The stress values obtained from the compression tests are evaluated at different strains to determine the strain rate sensitivity and flow instability maps and thus, to predict the formability of the material in the range of studied deformation parameters. These maps are correlated to the microstructure at specific deformation parameters.

Hot Deformation Behavior and Microstructure of U720Li Alloy

2013 ◽  
Vol 709 ◽  
pp. 143-147 ◽  
Author(s):  
Tao Wang ◽  
Zhao Li ◽  
Shu Hong Fu ◽  
Yong Zhang ◽  
Yu Xin Zhao ◽  
...  
Keyword(s):  
Grain Size ◽  
Flow Stress ◽  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Primary Phase ◽  
Compression Tests ◽  
Hot Deformation Behavior ◽  
Fine Grain ◽  
Lower Strain

The hot deformation behavior of U720Li was investigated by isothermal compression tests at temperature ranging from 1060-1180°C and strain rate from 0.001s-1 to 20s-1. The flow stress-strain curves and microstructures were investigated and a constitutive equation was established. It is found that flow stress is sensitive to stain rate and deformation temperature greatly. The higher stain rate resultes in a larger fluctuation in flow stress. The hot deformation activation energy is determined to be 552.8kJ/mol. Grain size increases with increasing temperature and decreases firstly and then increases with increasing strain rate. U720Li alloy should be deformed below the solve temperature of γ primary phase with lower strain rate in order to obtain the even and fine grain size.

Hot Deformation Behaviors and Microstructure Evolution of SiCp/Al Composites

2016 ◽  
Vol 849 ◽  
pp. 430-435 ◽  
Author(s):  
Shi Ming Hao ◽  
Jing Pei Xie ◽  
Li Ben Li ◽  
Ai Qin Wang ◽  
Wen Yan Wang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Structural Changes ◽  
True Strain ◽  
Peak Stress ◽  
Small Strain ◽  
Sensitive Material ◽  
Aluminium Matrix Composite ◽  
Compression Behavior ◽  
High Deformation ◽  
Deformation Behaviors

In order to explore the compressive properties of aluminium matrix composite reinforced with middle content SiC particles, hot compression behavior of 30%SiCp/2024A1 composite was investigated using Gleeble-1500 system at a temperatures range from 350 to 500°C and strain rates from 0.01 to 10 s−1. The associated structural changes were studied by OM, SEM and TEM observations. The results show that the true stress–true strain curves exhibited a peak stress at a small strain (<0.1), after which the flow stresses decreased monotonically until high strains, showing a dynamic flow softening. The stress level decreased with increasing deformation temperature and decreasing strain rate, indicating that the composite is a positive strain rate sensitive material. And therefore there will be a enough time for dynamic recrystallization to complete nucleation and growth at low strain rate and high deformation temperatures.

Sign in / Sign up

Export Citation Format

Share Document