Weighing System Design Based on Single Chip Microcomputer

2014 ◽  
Vol 1070-1072 ◽  
pp. 1572-1575
Author(s):  
Qing Zhuang
Keyword(s):  
High Resolution ◽  
System Design ◽  
Strain Sensor ◽  
Living Standards ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
The Core ◽  
Design Diagram ◽  
Main Components ◽  
Speed And Accuracy

As the living standards of people improve continually, commercial behavior is becoming more and more modernized, people also put forward new requirements for the speed and accuracy of goods measurement. This paper designs a weighing system of digital electronic scale which is similar to the MCU simulation, and gives the design diagram, hardware composition and software system. This system takes the 51 single chip microcomputer as the core, the main components are the dedicated 24 bits serial A/D conversion chip HX711, cantilever type resistance strain sensor, the four digital tube display. This design uses the dedicated 24 bits serial A/D conversion chip HX711, which has high resolution, simple peripheral interface, and occupies less I/O port, etc.

A Novel Full-Automatic Garbage Salvage Ship

2013 ◽  
Vol 791-793 ◽  
pp. 1921-1924
Author(s):  
Ke Ling Luo ◽  
Xu Dong Li ◽  
De Rui Song ◽  
Ping Wang ◽  
Jiao Fu ◽  
...  
Keyword(s):  
Control System ◽  
Obstacle Avoidance ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Power Circuit ◽  
The Core ◽  
Photoelectric Sensor

The garbage salvage ship is made from polystyrene plastic as hull framework and STC89C52 single-chip microcomputer to control the core, and consists of DC gear motor, photoelectric sensor, power circuit and other circuits. The system uses STC89C52 to control the boat to move forward, backward or turn through the I/O port. Tracing is finished by infrared obstacle avoidance sensor E18-D80NK. Working manner of the infrared obstacle avoidance sensor E18-D80NK was introduced and its application scheme based on STC89C52 single-chip microcomputer in the control system of garbage salvage ship was put forward.

An Wireless Collection and Monitoring System Design Based on Arduino

2014 ◽  
Vol 971-973 ◽  
pp. 1076-1080 ◽  
Author(s):  
Quan Sheng Yu ◽  
Mei Ying Duan ◽  
Tian Shun Zhang ◽  
Hong Gang Wu ◽  
Shao Kun Lu
Keyword(s):  
Remote Control ◽  
Power Consumption ◽  
Agricultural Production ◽  
Mesh Network ◽  
Small Scale ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
The Core ◽  
High Power Consumption ◽  
Easy Operation

Considering the current situation that the temperature control systems in market have the general disadvantages of complicated structure, high power consumption and tremendous cost, a new greenhouse temperature supervising system is designed, with a Arduino Mega 2560 single chip microcomputer as the core, XBEE as the short distance wireless transferring tools, and with function of displaying information in computers and remote control. The core component of this system is the Arduino software-hardware open source platform, which is currently popular in the market. This platform embraces the excellence of stability, low power consumption, cheap cost and easy operation as its advantages and selling points. XBEE can constitute the mesh network, each module of which can supplied as the route node, coordinator and terminal node. This system can achieve the functions of collecting data from sensors while is capable of displaying these data in the computers and put them under the network remote control. Easy to install, it can simultaneously achieve network monitoring several greenhouses. Enormous convenience to production inside the greenhouse is fulfilled due to these mentioned features as well, which makes it suitable to the small scale agricultural production.

Anti-Glare Device for Car Based on Single Chip Microcomputer

2013 ◽  
Vol 706-708 ◽  
pp. 1124-1127
Author(s):  
Hai Xia Li
Keyword(s):  
Light Intensity ◽  
Light Emitting Diode ◽  
Lamp Method ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Light Emitting ◽  
High Beam ◽  
The Core

Because the car headlamp light intensity is too large and it leads to accidents, This paper is based on the initiative to reduce the light intensity of their vehicles according headlights glare or close the high beam and open the lamp method, to achieve the purpose of the glare. The system is AT89C51 microcontroller as the core control, use of photodiode sensor to induction opposite the car headlights light intensity , when opposite car headlights light intensity up to a certain value, photodiode get a signal to the microcontroller ,and then microcontroller sends a signal, to control buzzer sound or not. When the buzzer sounded, using DAC0832 chip to control the brightness of the light emitting diode or control the light on and off and low beam enabled. When enabled for dipped beam, has been more than the antiglare range; after the scope enabled high beam, in order to achieve the anti-dazzle cycle. Through practice, the system has reached the anti-dazzle purpose and has practical value .

Circuit Design of Eyesight Protection Device which is Based on a Single Chip

2015 ◽  
Vol 727-728 ◽  
pp. 819-822
Author(s):  
Min Zhu
Keyword(s):  
Circuit Design ◽  
Software System ◽  
Protection Device ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
The Core ◽  
Circuit Timing ◽  
Basic Understanding ◽  
Circuit Development ◽  
Single Chip Microcontroller

Design the circuit of vision protector based on 8051 single chip microcontroller. The core of hardware is the 8051 single chip microcomputer, function circuit including sensor auxiliary sit straight alarm circuit, light alarm circuit, timing alarm circuit and alarm circuit. Have a basic understanding of SCM, then design each functional circuit, development software system, complete the design.

Design of an Intelligent Controller for Control and Protective Switching Based on Profibus

2012 ◽  
Vol 588-589 ◽  
pp. 1401-1404
Author(s):  
Zhi Yuan Cai ◽  
Hong Yuan Ai
Keyword(s):  
Real Time ◽  
Remote Monitoring ◽  
Host Computer ◽  
Single Chip ◽  
Real Time Monitoring ◽  
Single Chip Microcomputer ◽  
Switching Device ◽  
Intelligent Controller ◽  
The Core

An intelligent controller with capable communication for control and protective switching device (CPS) based on Profibus fieldbus was designed. The system with the single chip microcomputer as the core realized the function of measuring, protection, controlling and communication between CPS and host computer by Profibus fieldbus. The design could not only realize real-time monitoring for running state of multiple electromotor but also set the protection parameters of CPS and alarm function online by interface, which made CPS have remote monitoring function.

The Innovative Design and Reliability Research for Automatic Tray Filling Machine of Li/MnO2 Button Cell Battery

2013 ◽  
Vol 373-375 ◽  
pp. 2049-2052
Author(s):  
Hong Wu Zheng ◽  
Shu Zhong Lin ◽  
Lin Jiang Chang
Keyword(s):  
Control System ◽  
System Design ◽  
Control Design ◽  
Structure Design ◽  
Electrical System ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Innovative Design ◽  
Modeling Simulation ◽  
Button Cell

The principle conceptual design of the automatic tray filling machine of Li/MnO2 button cell battery and its control system are analyzed in the work. According to the the needs of production process putting the cell battery into the plate, it makes structure design and modeling simulation, completes electrical system design and program control design, relys on the Single chip microcomputer (MCU) system to achieve the human-computer interaction. In addition, this work verifies the feasibility and safety through the ANSYS modal analysis. After running the test more than a year, the product can well meet the production requirements.

Sign in / Sign up

Export Citation Format

Share Document