Study on Dispersion and Rheology of Particles in Water-Based Nano TiN Fluid

2015 ◽  
Vol 1095 ◽  
pp. 53-57
Author(s):  
Xin Wang Ouyang ◽  
Zhang Yong Wu ◽  
Zi Yong Mo
Keyword(s):  
Rheological Properties ◽  
Dispersion Medium ◽  
Mass Fraction ◽  
Deionized Water ◽  
Dispersion Effect ◽  
Step Method ◽  
Sedimentation Stability ◽  
Preparation Conditions ◽  
Water Based

The water-based nanoTiN fluids were prepared by nanoTiN particles, dispersion medium and dispersant using a two-step method. The dispersion and rheology of nanoparticles in water-based fluid were studied under different preparation conditions. The dispersion and rheology of prepared nanoTiN fluids were evaluated and analyzed from the mass fraction of nanoparticles, mass fraction of dispersant and type of dispersion medium respectively by using the analysis of sedimentation stability and rheological properties. The results show that the above-mentioned factors all have different degree of influence on nanofluids’ dispersion and rheology. The viscosity of nanofluids increases with mass fraction of nanoparticles. A balance amount of mass fraction of dispersant will improve nanofluids’ dispersity and fluidity. The dispersion effect of deionized water is the best when the nanoparticles dispersed in different dispersion medium.

Experimental Investigation on Surface Tension of Water-Based Graphene Oxide Nanofluids

2014 ◽  
Vol 1082 ◽  
pp. 297-301 ◽  
Author(s):  
Zhao Zhi Zheng
Keyword(s):  
Surface Tension ◽  
Experimental Investigation ◽  
Graphene Oxide ◽  
Mass Fraction ◽  
Deionized Water ◽  
Nanoparticle Size ◽  
Refrigeration Cycle ◽  
Absorption Refrigeration ◽  
Water Based ◽  
Increasing Temperature

The water-based graphene oxide nanofluids were prepared. The surface tension of nanofluids with different mass fraction, temperature and different nanoparticle size was researched. The surface tension value was measured through ringmethod. The experimental results show that the surface tension of nanofluids is increased with increasing the mass faction of nanoparticles. But the surface tension of nanofluids with maximum concentration (0.1 wt %) is only increased up to 2.9% compared with deionized water. The surface tension of nanofluids decreases with increasing temperature and decreasing nanoparticle size. The results of this paper may provide reference for the research of absorption liquid for absorption refrigeration cycle.

Transmission Performance of Water-Based Nano Fluid Based on Computational Fluid Dynamics

2015 ◽  
Vol 1095 ◽  
pp. 58-62
Author(s):  
Zheng Zheng Song ◽  
Zhang Yong Wu ◽  
Zi Yong Mo
Keyword(s):  
Mass Fraction ◽  
Good Resistance ◽  
Sedimentation Stability ◽  
Nano Fluid ◽  
Dispersing Agent ◽  
Shaped Tube ◽  
Velocity Flow ◽  
Water Based ◽  
Transmission Fluid ◽  
Membrane Treatment

The nanoboron carbide particle size is 60nm, dispersed in RO reverse osmosis membrane treatment water form water-based nanofluid by adding the dispersant. In experiment, Water-based nanoboron carbide fluid has good resistance sedimentation stability when adding sodium carboxymethyl cellulose as a dispersing agent. Prepared three kinds of water-based nanoboron carbide fluid, the mass fraction of nanoparticles is 0.6%, 0.8%, 1.0%. By establishing a model of U-shaped tube, simulated the water-based nanofluids flow field in U-shaped tube using FLUENT, get velocity flow lines picture and pressure variation graph by CFD post-processing. From simulation results obtained: Water-based nanoboron carbide has good transmission fluid performance when nanoparticles mass fraction of 0.8%.

scholarly journals Investigation of regulating rheological properties of water-based drilling fluids by ultrasound

2021 ◽  
Author(s):  
Wei-An Huang ◽  
Jing-Wen Wang ◽  
Ming Lei ◽  
Gong-Rang Li ◽  
Zhi-Feng Duan ◽  
...  
Keyword(s):  
Rheological Properties ◽  
Drilling Fluids ◽  
Water Based

Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Arild Saasen
Keyword(s):  
Rheological Properties ◽  
Pressure Loss ◽  
Drilling Fluid ◽  
Axial Flow ◽  
Drilling Fluids ◽  
Unstable Flow ◽  
Pressure Losses ◽  
Shear Dependent Viscosity ◽  
Water Based ◽  
Dependent Viscosity

Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.

Effect of Bi Addition on the Corrosion Behavior of Zirconium Alloys

2013 ◽  
Author(s):  
M. Y. Yao ◽  
B. X. Zhou ◽  
Q. Li ◽  
W. P. Zhang ◽  
L. Zhu ◽  
...  
Keyword(s):  
Solid Solution ◽  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Mass Fraction ◽  
Zirconium Alloys ◽  
Deionized Water ◽  
Second Phase ◽  
Micro Structure ◽  
Second Phase Particles ◽  
Structure Observation

In order to investigate systematically the effect of Bi addition on the corrosion resistance of zirconium alloys, different zirconium-based alloys, including Zr-4 (Zr-1.5Sn-0.2Fe-0.1Cr), S5 (Zr-0.8Sn-0.35Nb-0.4Fe-0.1Cr), T5 (Zr-0.7Sn-1.0Nb-0.3Fe-0.1Cr) and Zr-1Nb, were adopted to prepare the zirconium alloys containing Bi of 0∼0.5% in mass fraction. These alloys were denoted as Zr-4+xBi, S5+xBi, T5+xBi and Zr-1Nb+xBi, respectively. The corrosion behavior of these specimens was investigated by autoclave testing in lithiated water with 0.01 M LiOH or deionized water at 360°C/18.6 MPa and in superheated steam at 400 °C/10.3 MPa. The micro structure of the alloys was examined by TEM and the second phase particles (SPPs) were analyzed by EDS. Micro structure observation shows that the addition of Bi promotes the precipitation of Sn as second phase particles (SPPs) because Sn is in solid solution in α-Zr matrix in Zr-4, S5 and T5 alloys. The concentration of Bi dissolved in α-Zr matrix increase with the increase of Nb in the alloys, and the excess Bi precipitates as Bi-containing SPPs. The corrosion results show that the effect of Bi addition on the corrosion behavior of different zirconium-based alloys is very complicated, depending on their compositions and corrosion conditions. In the case of higher Bi concentration in α-Zr, the zirconium alloys exhibit better corrosion resistance. However, in the case of precipitation of Bi-containing SPPs, the corrosion resistance gets worse. This indicates that the solid solution of Bi in α-Zr matrix can improve the corrosion resistance, while the precipitation of the Bi-containing SPPs is harmful to the corrosion resistance.

scholarly journals Comparative Analysis of the Effect of Barite and Hematite on the Rheology of Water-Based Drilling Mud

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Osei H
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Attrition Rate ◽  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Drilling Operation ◽  
Water Based ◽  
Petroleum Resources ◽  
Drilling Muds ◽  
The Impact

High demand for oil and gas has led to exploration of more petroleum resources even at remote areas. The petroleum resources are found in deeper subsurface formations and drilling into such formations requires a well-designed drilling mud with suitable rheological properties in order to avoid or reduce associated drilling problems. This is because rheological properties of drilling muds have considerable effect on the drilling operation and cleaning of the wellbore. Mud engineers therefore use mud additives to influence the properties and functions of the drilling fluid to obtain the desired drilling mud properties especially rheological properties. This study investigated and compared the impact of barite and hematite as weighting agents for water-based drilling muds and their influence on the rheology. Water-based muds of different concentrations of weighting agents (5%, 10%, 15% and 20% of the total weight of the drilling mud) were prepared and their rheological properties determined at an ambient temperature of 24ᵒC to check their impact on drilling operation. The results found hematite to produce higher mud density, plastic viscosity, gel strength and yield point when compared to barite at the same weighting concentrations. The higher performance of the hematite-based muds might be attributed to it having higher specific gravity, better particle distribution and lower particle attrition rate and more importantly being free from contaminants. The water-based muds with hematite will therefore be more promising drilling muds with higher drilling and hole cleaning efficiency than those having barite.

scholarly journals Prediction of Formation Damage, Fluid Loss and Rheological Properties of Water Based Mud with Corn Cob

2020 ◽  
Vol 5 (10) ◽  
pp. 1269-1273
Author(s):  
Godwin Chukwuma Jacob Nmegbu ◽  
Bright Bariakpoa Kinate ◽  
Bari-Agara Bekee
Keyword(s):  
Rheological Properties ◽  
High Pressures ◽  
Chemical Properties ◽  
Analytical Models ◽  
Formation Damage ◽  
Fluid Loss ◽  
Drilling Mud ◽  
Corn Cob ◽  
Core Samples ◽  
Water Based

The extent of damage to formation caused by water based drilling mud containing corn cob treated with sodium hydroxide to partially replace polyanionic cellulose (PAC) as a fluid loss control additive has been studied. Core samples were obtained from a well in Niger Delta for this study with a permeameter used to force the drilling mud into core samples at high pressures. Physio-chemical properties (moisture content, cellulose and lignin) of the samples were measured and the result after treatment showed reduction. The corn cob was combined with the PAC in the ratio of 25-75%, 50-50% and 75-25% in the mud. Analyzed drilling mud rheological properties such as plastic viscosity, apparent viscosity, yield point and gel strength all decreased as percentage of corn cob increased in the combination and steadily decreased as temperature increased to 200oF. Measured fluid loss and pH of the mud showed an increase in fluid loss and pH in mud sample with 100% corn cob. The extent of formation damage was determined by the differences in the initial and final permeability of the core samples. Experimental data were used to develop analytical models that can serve as effective tool to predict fluid loss, rheological properties of the drilling mud at temperature up to 200oF and percentage formation damage at 100 psi.

Sign in / Sign up

Export Citation Format

Share Document