Numerical Simulation of Solar Ground-Source Heat Pump with Latent Heat Storage

2010 ◽  
Vol 129-131 ◽  
pp. 1069-1073 ◽  
Author(s):  
Fang Wang ◽  
Zhi Long Liu ◽  
Zhong Jian Li ◽  
Mao Yu Zheng
Keyword(s):  
Experimental Data ◽  
Phase Change ◽  
Latent Heat ◽  
Heat Pump ◽  
Heat Storage ◽  
Numerical Results ◽  
Outlet Temperature ◽  
Ground Source Heat Pump ◽  
Latent Heat Storage ◽  
Ground Source

Solar ground-source heat pump (SGSHP) system is unsteady when used to heating. Latent heat storage tank (LHST) was used appropriately in which phase change material (PCM) - CaCl2•6H2O was encapsulated in plastic kegs setting on the serpentine coil. PCM which was as controlling unit of the phase change heat transfer model were solved numerically by an enthalpy-based finite differences method and was validated by experimental data. In order to reflect the effect of the system, two days were chosen to compare the numerical results with experimental data. Inlet and outlet temperature of the water in the LHST, temperature of PCM and storage & emission heat of LHST were measured. The trends of the variation of numerical results and experimental data were in close agreement. Numerical results can reflect the operation mode of the system very well.

Selection of Phase Change Materials for Latent Heat Storage

2017 ◽  
Vol 13 (1) ◽  
Author(s):  
J. Martínez-Gómez ◽  
E. Urresta ◽  
D. Gaona ◽  
G. Guerrón
Keyword(s):  
Phase Change ◽  
Latent Heat ◽  
Phase Change Materials ◽  
Heat Storage ◽  
Latent Heat Storage ◽  
Toma De Decisiones ◽  
Selection Of

Esta investigación tiene como objetivo seleccionar un material de cambio de fase (PCM) que cumplen mejor la solución del almacenamiento de energía térmica entre 200-400 ° C y reducir el costo de producción. El uso de métodos multicriterios de toma de decisiones (MCMD) para la evaluación fueron proporcionales implementados como COPRAS-G, TOPSIS y VIKOR. La ponderación de los criterios se realizó por el método AHP (proceso analítico jerárquico) y los métodos de entropía. La correlación de los resultados entre los tres métodos de clasificación ha sido desarrollada por el coeficiente de correlación de Spearman. Los resultados ilustran el mejor y la segundo mejor opción para los tres MCDM fueron NaOH y KNO3. Además, tenía valores de correlación de Spearman entre los métodos excede de 0.714.

Thermal Conductivity Enhancement in a Latent Heat Storage Device

2013 ◽  
Vol 860-863 ◽  
pp. 590-593
Author(s):  
Cha Xiu Guo ◽  
Ding Bao Wang ◽  
Gao Lin Hu
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Solid State ◽  
Liquid Phase ◽  
Phase Change ◽  
Latent Heat ◽  
Heat Storage ◽  
Storage Device ◽  
Latent Heat Storage ◽  
Conductivity Enhancement

High conductivity porosity materials are proposed to enhance the phase change materials (PCM) in order to solve the problem of low conductivity of PCM in the latent heat storage device (LHSD), and two-dimensional numerical simulation is conducted to predict the performance of the PCM by CFD software. During the phase change process, the PCM is heated from the solid state to the liquid phase in the process of melting and from the liquid phase to the solid state in the solidification process. The results show that porosity materials can improve heat transfer rate effectively, but the effect of heat transfer of Al foam is superior to that of graphite foam although the heat storage capacity is almost the same for both. The heat transfer is enhanced and the solidification time of PCM is decreased since the effective thermal conductivity of composite PCM is increased.

Sign in / Sign up

Export Citation Format

Share Document