Research on Stability of High Strength Aluminum Alloy Columns Loaded by Axial Compressive Load

2010 ◽  
Vol 168-170 ◽  
pp. 1915-1920 ◽  
Author(s):  
Xi Mei Zhai ◽  
Yu Jin Wang ◽  
Hai Wu ◽  
Feng Fan
Keyword(s):  
Finite Element ◽  
Aluminium Alloy ◽  
Mechanical Performance ◽  
Compressive Load ◽  
High Strength ◽  
General Purpose ◽  
Element Analysis ◽  
Hollow Section ◽  
Axial Compressive Load ◽  
Calculation Results

This paper reports experimental study of 17 high strength aluminium alloy specimens of type of 6082-T6 under axially compressed load including I-section column, rectangular hollow section. The general-purpose non-linear finite element analysis software ABAQUS is adopted to simulate the mechanical performance and overall buckling of aluminium alloy columns. The feasibility of finite element method has been verified through the comparison between the simulation results and the test finding. Finally, based on the experimental data and numerical calculation results, a useful column curve formulation to calculate the coefficient of stability of 6082-T6 aluminium alloy columns loaded by axial compressive load is derived. Comparison between column curves from proposed formulation and different code and test results has been presented, from which the validation of the proposed formulation has been verified.

scholarly journals Finite Element Analysis on Behavior of Reinforced Hollow High Strength Concrete Filled Square Steel Tube Short Columns under Axial Compression

2021 ◽  
Vol 2101 (1) ◽  
pp. 012059
Author(s):  
Z J Yang ◽  
X Li ◽  
G C Li ◽  
S C Peng
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Strength Concrete ◽  
Mechanical Performance ◽  
Concrete Strength ◽  
High Strength ◽  
Steel Tube ◽  
Element Analysis ◽  
Steel Strength ◽  
Square Steel Tube

Abstract Hollow concrete-filled steel tubular (CFST) member is mainly adopted in power transmission and transformation structures, but when it is used in the superstructure with complex stress, the hollow CFST member has a low bearing capacity and is prone to brittle failure. To improve the mechanical performance of hollow CFST members, a new type of reinforced hollow high strength concrete-filled square steel tube (RHCFSST) was proposed, and its axial compression performance was researched. 18 finite element analysis (FEA) models of axially loaded RHCFSST stub columns were established through FEA software ABAQUS. The whole stress process of composite columns was studied, and parametric studies were carried out to analyze the mechanical performance of the member. Parameters of the steel strength, steel ratio, deformed bar and sandwich concrete strength were varied. Based on the simulation results, the stress process of members can be divided into four stages: elastic stage, elastoplastic stage, descending stage and gentle stage. With the increase of steel strength, steel ratio, the strength of sandwich concrete and the addition of deformed bars, the ultimate bearing capacity of members also increases. Additionally, the increment of those parameters will improve the ductility of the member, except for the sandwich concrete strength.

Calculation methods of bridge deck for prestressed short rib T-beam bridges

2020 ◽  
pp. 1-13
Author(s):  
Sijia Wang ◽  
Tianlai Yu
Keyword(s):  
Finite Element ◽  
Bridge Deck ◽  
Mechanical Performance ◽  
Test Results ◽  
Analysis Method ◽  
Slab Method ◽  
Element Analysis ◽  
Calculation Results ◽  
Beam Bridge ◽  
T Beam

Because of the low height of the prestressed short rib T-beam bridge and the poor torsion resistance of the main beam, the positive moment in the middle span of the bridge deck will increase correspondingly compared with the normal rib beam bridge. At present, there is little research on the calculation method of the bridge deck of the prestressed short rib T-beam bridge. In this paper, the space finite element method and the continuous one-way slab method are used to calculate the forces on the bridge deck, based on the space finite element method, a finite element elastic supported continuous beam method is proposed to calculate the forces on the bridge deck. By comparing the calculation results of the three methods with the test results, the reasonable calculation method of the bridge deck is studied. The results show that the spatial finite element analysis method can simulate the mechanical performance of the deck of the bridge of the prestressed short rib T-beam bridge well, the stress calculation results are consistent with the test results, and the calculation accuracy is high, which can be used in the actual engineering design; The finite element analysis method of elastic support continuous beam can also simulate the mechanical performance of the deck of the bridge of the prestressed short rib T-beam bridge. The concept of the method is clear, the calculation is convenient, and it is more suitable for the application of engineering design; The calculation results of the continuous one-way slab method are too large to be safe for design.

scholarly journals Finite element analysis of bolt shear connection of steel-concrete composite structure

2020 ◽  
Vol 198 ◽  
pp. 01027
Author(s):  
Zhishun Pan
Keyword(s):  
Finite Element ◽  
Composite Structure ◽  
Composite Structures ◽  
Mechanical Performance ◽  
Concrete Strength ◽  
High Strength ◽  
Shear Capacity ◽  
Simulation Software ◽  
Element Analysis ◽  
Shear Connectors

Bolted shear connectors are an important component to ensure that steel-concrete composite structures can work together. High-strength bolt shear connectors can replace traditional stud connectors because of their disassembly, good mechanical performance and fatigue resistance. It applied to steel-concrete composite structure. In order to study the influencing factors of the bearing capacity of high-strength bolted shear connectors, this paper uses ABAQUS finite element simulation software as a research tool to establish a reasonable finite element model to study the influence of bolt strength, bolt diameter and concrete strength on bolted shear connectors. Studies have shown that increasing the diameter, strength, and concrete strength of bolted connections can effectively increase the bolt’s shear capacity.

Finite Element Analysis of Anti-Reflective Crack for Geosynthetic in Asphalt Overlay of Airport Runway

2012 ◽  
Vol 503-504 ◽  
pp. 847-850
Author(s):  
Zhi Gang Luo ◽  
Yan Liu ◽  
Sui Yuan Wang ◽  
Bo Diao
Keyword(s):  
Finite Element ◽  
Surface Deformation ◽  
Element Model ◽  
General Purpose ◽  
Main Role ◽  
Element Analysis ◽  
Finite Element Software ◽  
Asphalt Overlay ◽  
Calculation Results ◽  
Airport Runway

To make clear the work mechanism of geosynthetic in asphalt overlay under the aircraft wheel loads, one 3D dimension finite element model was constructed on the basis of the general purpose finite element software ABAQUS. Numerical calculation results with different geosynthetic modulus are presented in this paper, and show that it is very limited for geosynthetic to reduce bottom stress and surface deformation of asphalt overlay, and asphalt overlay bottom is in compression state, thus, geosynthetic can not exert it’s film tension function, namely the main role of geosynthetic is not to bear loads together with asphalt overlay, but to improve stress state of asphalt overlay for preventing cracks appearance or delaying cracks expansion.

scholarly journals Design and analysis of concrete-filled tubular flange girders under combined loading

2021 ◽  
pp. 136943322110015
Author(s):  
Rana Al-Dujele ◽  
Katherine Ann Cashell
Keyword(s):  
Finite Element ◽  
Axial Force ◽  
Failure Modes ◽  
Numerical Study ◽  
Combined Loading ◽  
Torsional Stiffness ◽  
Fe Model ◽  
Combined Effects ◽  
Element Analysis ◽  
Hollow Section

This paper is concerned with the behaviour of concrete-filled tubular flange girders (CFTFGs) under the combination of bending and tensile axial force. CFTFG is a relatively new structural solution comprising a steel beam in which the compression flange plate is replaced with a concrete-filled hollow section to create an efficient and effective load-carrying solution. These members have very high torsional stiffness and lateral torsional buckling strength in comparison with conventional steel I-girders of similar depth, width and steel weight and are there-fore capable of carrying very heavy loads over long spans. Current design codes do not explicitly include guidance for the design of these members, which are asymmetric in nature under the combined effects of tension and bending. The current paper presents a numerical study into the behaviour of CFTFGs under the combined effects of positive bending and axial tension. The study includes different loading combinations and the associated failure modes are identified and discussed. To facilitate this study, a finite element (FE) model is developed using the ABAQUS software which is capable of capturing both the geometric and material nonlinearities of the behaviour. Based on the results of finite element analysis, the moment–axial force interaction relationship is presented and a simplified equation is proposed for the design of CFTFGs under combined bending and tensile axial force.

Study on the Local Buckling Behavior of Steel Equal Angle Members under Axial Compression with the Steel Strength Variation

2011 ◽  
Vol 374-377 ◽  
pp. 2430-2436
Author(s):  
Gang Shi ◽  
Zhao Liu ◽  
Yong Zhang ◽  
Yong Jiu Shi ◽  
Yuan Qing Wang
Keyword(s):  
Finite Element ◽  
Axial Compression ◽  
High Strength Steel ◽  
Local Buckling ◽  
Steel Structures ◽  
High Strength ◽  
Element Analysis ◽  
Equal Angle ◽  
Buckling Behavior ◽  
Steel Strength

High strength steel sections have been increasingly used in buildings and bridges, and steel angles have also been widely used in many steel structures, especially in transmission towers and long span trusses. However, high strength steel exhibits mechanical properties that are quite different from ordinary strength steel, and hence, the local buckling behavior of steel equal angle members under axial compression varies with the steel strength. However, there is a lack of research on the relationship of the local buckling behavior of steel equal angle members under axial compression with the steel strength. A finite element model is developed in this paper to analyze the local buckling behavior of steel equal angle members under axial compression, and study its relationship with the steel strength and the width-to-thickness ratio of the angle leg. The finite element analysis (FEA) results are compared with the corresponding design method in the American code AISC 360-05, which provides a reference for the related design.

Finite Element Analysis of Tianerya Trench-Buried Inverted Siphon

2013 ◽  
Vol 804 ◽  
pp. 320-324
Author(s):  
Xiang Zan Xie
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Calculation ◽  
Construction Process ◽  
Element Calculation ◽  
Element Analysis ◽  
Operational Process ◽  
Inverted Siphon ◽  
Calculation Results ◽  
Calculation Software

This paper adopts universal finite element calculation software to carry out finite element analysis for Tianerya trench-buried inverted siphon. Researching variation law of the inverted siphons stress and displacement in construction process and operational process. The calculation results further shown design schemes rationality and safety. The analysis results provide a certain reference for design of trench-buried inverted siphon structure.

Sign in / Sign up

Export Citation Format

Share Document