Influence of the Arc Suppression Coil with Parallel Resistance on Single-Phase Arc Grounding Overvoltage

2013 ◽  
Vol 676 ◽  
pp. 284-288 ◽  
Author(s):  
Han Xue ◽  
Ji Jiang Song ◽  
Yu Chong Cui
Keyword(s):  
Single Phase ◽  
Neutral Point ◽  
Residual Flow ◽  
Phase Voltage ◽  
Voltage Rise ◽  
Arc Suppression Coil ◽  
Voltage Recovery ◽  
Parallel Resistance ◽  
Resistance Value

Neutral point grounding method with an arc suppression coil and a parallel resistance is a method that can inhibit arc overvoltage effectively. Through the simulation of arc suppression coil with parallel resistance in the situation of different resistance value, we can obtain if the parallel resistance is too big, it will produce overvoltage in the later of voltage recovery; if the parallel resistance is too small, it is easy to produce larger grounding residual flow, going against quenching of arc; Whether over compensation or owe compensation, oversized out-of-resonance degree will cause the fault phase voltage recovery oscillation overvoltage, small out-of-resonance degree is beneficial to the fault phase voltage rise slowly.

Automatic Tuning Arc Suppression Coil Current in a Small Grounding System

2014 ◽  
Vol 620 ◽  
pp. 398-401 ◽  
Author(s):  
Hui Lin Zhang ◽  
Yu Bo Zhao ◽  
Feng Zhen Liu
Keyword(s):  
Common Good ◽  
Single Phase ◽  
Short Circuit ◽  
Neutral Point ◽  
Automatic Tuning ◽  
Normal Operation ◽  
Ground Fault ◽  
Arc Suppression Coil ◽  
Current Flows ◽  
Petersen Coil

Equipped Petersen coil systems can compensate for the capacitance of the line current, the single-phase ground fault current flows through the capacitor grounding point for the minimum point of the arc of a reliable ground fault arc , to avoid reigniting , prevent arcing ground fault point phase faults caused by short circuit . But will also prevent the neutral point displacement due to different switching operation of single-phase disconnection caused by other factors , to avoid the neutral point voltage is too high, the threat of insulation safety equipment . In addition Petersen coil in the normal operation of the power grid , and can effectively prevent resonance over-voltage , prevent equipment damage caused thereby , better protection of system security , stability, and high-quality operation. Automatic tuning arc suppression coil can meet the common good basis to eliminate the role of the Petersen coil grid resonance occurs , install and use the effect is significant.

Adjusting the Degree of Compensation of Small Current Grounding System Petersen Coil

2014 ◽  
Vol 620 ◽  
pp. 394-397
Author(s):  
Xiang Dong Zhao ◽  
Feng Zhen Liu ◽  
Ye Tian
Keyword(s):  
Single Phase ◽  
Neutral Point ◽  
Normal Operation ◽  
Stable Operation ◽  
Small Current ◽  
Operating Personnel ◽  
Grounding System ◽  
Arc Suppression Coil ◽  
Petersen Coil ◽  
Improve Reliability

While the system is equipped with Petersen coil caused by the switching operation can prevent a different period , single-phase disconnection and other factors neutral point displacement , so that the neutral point voltage is too high, the threat of insulation safety equipment . Also in the normal operation of the power grid , but also effectively prevent resonance over-voltage , prevent system damage caused thereby , better protection of system security , stability, and high-quality operation. Summary of small current grounding system after the formation of arc suppression coil compensation compensation network system , in order to better prevent arc short-circuiting the system of single phase , which is to ensure security of supply , improve reliability and power quality .In the paper, small current grounding system Petersen coil with the compensation adjustment is carried out and some analysis, study and research is done in order to improve the operating personnel awareness and emphasis on small current grounding system , and better ensure the safety of the small current grounding system , stable operation.

Locating Method of Single-Phase Grounding Fault in Small Current Grounding System Based on Distribution Automation

2013 ◽  
Vol 321-324 ◽  
pp. 1423-1428
Author(s):  
Jun Zhou ◽  
Ke Zheng Cao
Keyword(s):  
Single Phase ◽  
System Modeling ◽  
Simulation Method ◽  
Neutral Point ◽  
Distribution Automation ◽  
Fault Line ◽  
Small Current ◽  
Grounding System ◽  
Arc Suppression Coil ◽  
Zero Sequence

In case of the arc suppression coil for neutral point grounding of small current grounding system, when single-phase grounding fault occurs, due to the arc suppression coil for fault line of the compensation effect of the zero sequence current, the fault features is not obvious, it can't implement the fault line selection and fault point location. This paper puts forward a method of change fault lines zero sequence current shortly, namely a resistance inductance (RL) series branch parallel in arc suppression coil, the series branch acts on the system shortly and changes arc suppression coil compensation degree temporarily in single-phase grounding fault. The change of zero sequence residual current only appears the loop from the neutral point to the fault point via the fault line, using FTU (feeder terminal units) on lines monitor the change of zero sequence current on each nodes for fault regional location. And prove this theory the feasibility of the by using MATLAB software of system modeling simulation method.

MEASUREMENT OF NONSINUSOIDAL FACTOR FOR SINGLE-PHASE VOLTAGE USING OF SYMMETRIC COMPONENTS FILTERS

2016 ◽  
Vol 2016 (4) ◽  
pp. 20-22
Author(s):  
D.K. Makov ◽  
◽  
O.V. Polishchuk ◽  
Keyword(s):  
Single Phase ◽  
Phase Voltage

Three-phase to Single-phase Matrix Converter for Improvement of Three-phase Voltage Unbalance in Distribution System

2015 ◽  
Vol 135 (3) ◽  
pp. 168-180 ◽  
Author(s):  
Ryota Mizutani ◽  
Hirotaka Koizumi ◽  
Kentaro Hirose ◽  
Kazunari Ishibashi
Keyword(s):  
Distribution System ◽  
Single Phase ◽  
Matrix Converter ◽  
Phase Voltage ◽  
Voltage Unbalance ◽  
Three Phase

Study on Selective Leakage Protection System of Mine High Voltage Grid Based on Harmonic Phase Comparison

2015 ◽  
Vol 9 (1) ◽  
pp. 253-262
Author(s):  
Liu Zhongfu ◽  
Zhang Junxing ◽  
Shi Lixin ◽  
Yang Yaning
Keyword(s):  
High Voltage ◽  
Power Supply ◽  
Power Supply System ◽  
Supply System ◽  
Neutral Point ◽  
Arc Suppression Coil ◽  
Zero Sequence ◽  
Harmonic Extraction ◽  
Power Direction ◽  
The Stability

As for the wide application of arc suppression coil to the grounding in neutral point of mine high voltage grid, grid leakage fault rules and harmonic characteristics of the neutral point grounding system through arc suppression coil are analyzed, the selective leakage protection program “zero-sequence voltage starts, fifth harmonics of grid zerosequence voltage and zero-sequence current are extracted for phase comparison” is proposed, and corresponding fifth harmonic extraction circuit and power direction discrimination circuit are designed. The experimental results show that the protective principle applies not only to the neutral point insulated power supply system, but also to the power supply system in which neutral point passes arc suppression coil, which can solve selective leakage protection problems under different neutral grounding ways, improving the reliability of selective leakage and guaranteeing the stability of the action value.

Design and Implementation of Wireless Voltage Monitoring System Based on Zigbee

2017 ◽  
Vol 12 (3) ◽  
pp. 83-96 ◽  
Author(s):  
Luo Xiaohui
Keyword(s):  
Monitoring System ◽  
Single Phase ◽  
Low Cost ◽  
Moving Average ◽  
Voltage Sensor ◽  
Wireless Transmission ◽  
Phase Voltage ◽  
Medium Voltage ◽  
Wireless Monitoring ◽  
Three Phase

This paper proposed a low cost wireless monitoring system based on ZigBee wireless transmission, and designed a new floating voltage sensor which is suitable for the monitoring of medium voltage and high voltage(MV/HV) public equipment. The system used TI-CC2530 as the controller, proposed a new moving average voltage sensing(MAVS) algorithm by reasonable assumptions, and adopted algorithms to perform the theoretical analysis for the single phase and three-phase voltage. At last, the author carried out a practical experiment on the wireless floating voltage sensor under the voltage up to 30kV, the experimental results showed that the proposed low cost wireless sensor can achieve a good voltage monitoring function, and the error is less than 3%.

scholarly journals DESIGN OF A SINGLE-PHASE RADIAL FLUX PERMANENT MAGNET GENERATOR WITH VARIATION OF THE STATOR DIAMETER

2019 ◽  
Vol 81 (4) ◽  
Author(s):  
Hari Prasetijo ◽  
Winasis Winasis ◽  
Priswanto Priswanto ◽  
Dadan Hermawan
Keyword(s):  
Magnetic Flux ◽  
Permanent Magnet ◽  
Flux Density ◽  
Single Phase ◽  
Air Gap ◽  
Wire Diameter ◽  
Terminal Phase ◽  
Magnetic Flux Density ◽  
Phase Voltage ◽  
Radial Flux

This study aims to observe the influence of the changing stator dimension on the air gap magnetic flux density (Bg) in the design of a single-phase radial flux permanent magnet generator (RFPMG). The changes in stator dimension were carried out by using three different wire diameters as stator wire, namely, AWG 14 (d = 1.63 mm), AWG 15 (d = 1.45 mm) and AWG 16 (d = 1.29 mm). The dimension of the width of the stator teeth (Wts) was fixed such that a larger stator wire diameter will require a larger stator outside diameter (Dso). By fixing the dimensions of the rotor, permanent magnet, air gap (lg) and stator inner diameter, the magnitude of the magnetic flux density in the air gap (Bg) can be determined. This flux density was used to calculate the phase back electromotive force (Eph). The terminal phase voltage (V∅) was determined after calculating the stator wire impedance (Z) with a constant current of 3.63 A. The study method was conducted by determining the design parameters, calculating the design variables, designing the generator dimensions using AutoCad and determining the magnetic flux density using FEMM simulation.  The results show that the magnetic flux density in the air gap and the phase back emf Eph slightly decrease with increasing stator dimension because of increasing reluctance. However, the voltage drop is more dominant when the stator coil wire diameter is smaller. Thus, a larger diameter of the stator wire would allow terminal phase voltage (V∅) to become slightly larger. With a stator wire diameter of 1.29, 1.45 and 1.63 mm, the impedance values of the stator wire (Z) were 9.52746, 9.23581 and 9.06421 Ω and the terminal phase voltages (V∅) were 220.73, 221.57 and 222.80 V, respectively. Increasing the power capacity (S) in the RFPMG design by increasing the diameter (d) of the stator wire will cause a significant increase in the percentage of the stator maximum current carrying capacity wire but the decrease in stator wire impedance is not significant. Thus, it will reduce the phase terminal voltage (V∅) from its nominal value.

Sign in / Sign up

Export Citation Format

Share Document