Cogon Grass Fiber-Epoxidized Natural Rubber Composites

2013 ◽  
Vol 747 ◽  
pp. 375-378 ◽  
Author(s):  
Chaiwat Ruksakulpiwat ◽  
Wasaphon Wanasut ◽  
Apikiat Singkum ◽  
Ruksakulpiwat Yupaporn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Acid Treatment ◽  
Treatment Time ◽  
Treatment Method ◽  
Epoxidized Natural Rubber ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites

This research shows a great potential of cogon grass fiber to be used as a reinforcement in epoxidized natural rubber composites. The thermal and mechanical properties of cogon grass fiber-epoxidized natural rubber composites were studied. The chemical treatment of cogon grass fiber to be used as a reinforcing filler was revealed. Effects of fiber treatment method and treatment time of cogon grass fiber on thermal properties of the fibers and their composites were elucidated. The addition of cogon grass fiber into epoxidized natural rubber (ENR) improved the mechanical properties of the composites.The result indicated that alkaline treatment followed by acid treatment of cogon grass fiber led to an increase in thermal decomposition temperature and mechanical properties of the composites more than that without acid treatment. With increasing the amount of fiber, tensile strength of ENR composites were significantly increased while elongation at break was insignificantly changed. ENR with the addition of 4-Amino-6-hydroxy-2-mercaptopyrimidine monohydrate as coupling agent (ENRC) was shown to have higher tensile strength, modulus at 200% elongation and elongation at break than ENR. Improved mechanical properties were also obtained in ENRC composites compared to those of ENR composites.

Physical Properties of Rice Husk Fiber/Natural Rubber Composites

2011 ◽  
Vol 410 ◽  
pp. 90-93 ◽  
Author(s):  
Ladawan Srisuwan ◽  
Kasama Jarukumjorn ◽  
Nitinat Suppakarn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Rice Husk ◽  
Crosslink Density ◽  
Morphological Properties ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites ◽  
Reinforcing Filler

In this study, rice husk fiber (RHF) was used as a reinforcing filler for natural rubber (NR). NR composites were prepared at various RHF contents, i.e., 10, 20, 30, 40 and 50 phr. Sulfur conventional vulcanization was used. Effect of RHF content on cure characteristics, mechanical properties and morphological properties of NR composites were investigated. The results showed that scorch and cure times of RHF/NR composites were not affected by increasing RHF content. Crosslink density, tensile strength, elongation at break and tear strength of NR composites slightly decreased with increasing RHF content whereas M100 and M300 of the composites slightly increased with increasing RHF content.

scholarly journals Thermal, Morphological and Physic-Mechanical Properties of Natural Rubber - CaCO3 Composites Using Jatropha Oil as Softener.

2018 ◽  
Vol 156 ◽  
pp. 05016 ◽  
Author(s):  
Nasruddin ◽  
Tri Susanto
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Abrasion Resistance ◽  
Compositional Analysis ◽  
Critical Issue ◽  
Green Technology ◽  
Jatropha Oil ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites

The urgency of green technology in rubber compounding has become a critical issue recently. In this research, the effect of using renewable resources in rubber compounding has been studied. Commercial Calcium Carbonate, Silica and Jatropha Oil were used in natural rubber composite. The research was designed by varying the types of commercial filler namely CaCO3 (47-51) phr, silica (47-51) phr and Jatropha Oil (4-6) phr in natural rubber composites (SIR-20). The formulas were intentionally designed for rubber tips vulcanizates. The samples were characterized by the determination of physic-mechanical, thermal (TGA) and morphological (SEM) properties. From the measured results, there is no significant effect on the tensile strength, specific gravity, and hardness on the loading of commercial CaCO3 and Silica in natural rubber composites using Jatropha Oil. However, a slight difference in elongation at break and abrasion resistance could be detected. Compared to the commercial rubber tips, the rubber tips produced in this research have higher tensile strength, elongation at break and abrasion resistance. Due to the usage of commercial CaCO3 and Silica, the SEM micrographs show rough surface because of the agglomeration. The thermogram shows clearly the compositional analysis of the rubber tips vulcanizates consist of Jatropha Oil and natural rubber, CaCO3, ash and other filler residues such as Silica.

Effect of Curing System on Morphological, Rheological, Thermal and Mechanical Properties of Thermoplastic Vulcanizates Based on Epoxidized Natural Rubber and Polypropylene

2012 ◽  
Vol 602-604 ◽  
pp. 690-695
Author(s):  
Hua Dong Wang ◽  
Rui Wang ◽  
Mao Fang Huang ◽  
Qi Yang
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Epoxidized Natural Rubber ◽  
Thermal And Mechanical Properties ◽  
Rheological Analysis ◽  
Elongation At Break ◽  
Thermoplastic Vulcanizates ◽  
Internal Mixer

Thermoplastic vulcanizates (TPVs) based on epoxidized natural rubber (ENR) and polypropylene (PP) were prepared in an internal mixer at 180°C. The effects of curing systems (i.e., sulfur and peroxide) on morphological, rheological, thermal and mechanical properties were studied. It is found that the sulfur cured TPVs show higher tensile strength, tear strength and elongation at break than those cured with the DCP systems. The rheological analysis indicates that TPVs cured with DCP system show lower apparent shear viscosity than those with sulfur system. SEM studies show that TPVs vulcanized with DCP system exhibit smaller and finely dispersed rubber domains, which provides it higher thermal stability than sulfur cured TPVs.

Tensile Properties of Wollastonite Filled High Density Polyethylene/Natural Rubber Composites

2015 ◽  
Vol 754-755 ◽  
pp. 215-219
Author(s):  
Ismail Yuhaida ◽  
Husseinsyah Salmah ◽  
Hanafi Ismail ◽  
Zainuddin Firuz
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
High Density Polyethylene ◽  
High Density ◽  
Inorganic Filler ◽  
Rotor Speed ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites

Wollastonite is one type of inorganic filler. The effects of wollastonite loading on tensile properties of wollastonite (WS) filled high density polyethylene (HDPE)/Natural Rubber (NR) composites was studied. The HDPE/NR/WS composites were prepared by using Brabender EC Plus at a temperature of 180 °C with rotor speed of 50 rpm for 10 min. It was found that the increasing of wollastonite loading had decreased the tensile strength and elongation at break, whereas the Young’s modulus of the HDPE/NR/WS composites had increased with the increasing of wollastonite loading.

The Study of Using Bio-Filler from Cassava Pulp in Natural Rubber Composites

2013 ◽  
Vol 747 ◽  
pp. 371-374 ◽  
Author(s):  
Watcharin Ruangudomsakul ◽  
Chaiwat Ruksakulpiwat ◽  
Ruksakulpiwat Yupaporn
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Cellulose Fiber ◽  
Cassava Starch ◽  
Morphological Properties ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Cassava Pulp ◽  
Natural Rubber Composites ◽  
Properties Of Composites

Cassava pulp (CP) is an inexpensive and broadly available waste by-product from cassava starch production. This by-product is basically constituted of cellulose fiber and residual starch. In this study, cassava pulp was mixed with natural rubber (NR) with various contents using two roll mills to obtain CP/NR composites. Natural rubber grafted glycidyl methacrylate (NR-g-GMA) was used as compatibilizer in CP/NR/NR-g-GMA composites. Sulfur conventional vulcanization was used. The composite specimens were prepared by compression molding. Mechanical properties and morphological properties of composites were investigated. The results showed that tensile strength was significantly increased with increasing content of cassava pulp up to 20 phr. However, when cassava pulp was increased more than 30 phr, tensile strength was slightly decreased. Elongation at break of NR composites was not changed with increasing cassava pulp. The modulus of NR composites was increased with increasing cassava pulp content. Morphological properties of CP/NR composites was elucidated as well.

Electrical and Mechanical Properties of Conductive Carbon Black Filled Epoxidized Natural Rubber

2013 ◽  
Vol 844 ◽  
pp. 255-258 ◽  
Author(s):  
Suradet Matchawet ◽  
Charoen Nakason ◽  
Azizon Kaesaman
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Black ◽  
Natural Rubber ◽  
Volume Fraction ◽  
Epoxidized Natural Rubber ◽  
Rubber Matrix ◽  
Elongation At Break ◽  
Conductive Carbon Black ◽  
Conductivity Increase

Electrical and mechanical properties of epoxidized natural rubber (ENR-25) filled with conductive carbon black (CCB) have been investigated. SEM was used to analyze dispersion of CCB particles in rubber matrix. The results indicated that the AC conductivity increase with increasing volume fraction of carbon black as well as frequency. The percolation thresholds of the electrical conductivity was found at 0.10 volume fraction of CCB. Furthermore, addition of CCB at volume fraction 0.05 caused the highest tensile strength of the composites. The tensile strength and elongation at break were decreased with increasing content of CCB greater than 0.05 volume fraction. However, the volume fraction of CCB at 0.10 demonstrated the most suitable proportion for the ENR composites with superior electrical and mechanical properties.

Mechanical Properties of Montmorillonite-Filled Natural Rubbers Compatibilized by Epoxidized Natural Rubbers

2012 ◽  
Vol 488-489 ◽  
pp. 93-97
Author(s):  
Pranut Potiyaraj ◽  
Sittiporn Ngamsurat ◽  
Wasan Poklong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Epoxidized Natural Rubber ◽  
Elongation At Break ◽  
Modified Montmorillonite ◽  
Rubber Compounds ◽  
Filler Dispersion ◽  
Reinforcing Filler ◽  
Organomodified Montmorillonite

The effects of epoxidized natural rubber as a compatibilizer in modified-montmorillonite filled natural rubber were studied. Natural rubber was compounded with 2, 5 and 10 parts per hundred rubber (phr) of organomodified montmorillonite as a reinforcing filler and cured by using a conventional sulfuric system. Epoxidized natural rubber with 25 and 50 mol% epoxidic units (ENR25 and ENR50, respectively) was used as compatibilizer at the amount of 5, 10 and 15 phr. Rubber compounds were then tested for their curing properties. Test specimens for mechanical testing were prepared by compression molding. The use of montmorillonite as a filler in natural rubber efficiently improved mechanical properties that are tensile strength, modulus, elongation at break, tear strength and hardness, especially with the small amount of montmorillonite. This is supposed to be related to intercalation and exfoliation process. The increasing amount of montmorillonite caused the filler to be agglomerated thus the reinforcing efficiency was reduced and some mechanical properties were dropped. It was further founded that epoxidized natural rubber compatibilized montmorillonite filled natural rubber effectively. As the amount of epoxidized natural rubber increased, the mechanical properties tended to increase. The presence of epoxidized natural rubber improved filler-rubber interaction and filler dispersion. The compatibilizing efficiency of ENR25 was slightly superior to that of ENR50. This is because ENR 25 contains more double bonds than ENR 50 hence higher strain-induced crystallinity is occurred

Sisal Fiber/Natural Rubber Composites: Effect of Fiber Content and Interfacial Modification

2011 ◽  
Vol 410 ◽  
pp. 63-66 ◽  
Author(s):  
Wittawat Wongsorat ◽  
Nitinat Suppakarn ◽  
Kasama Jarukumjorn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Fiber Content ◽  
Sisal Fiber ◽  
Elongation At Break ◽  
Interfacial Modification ◽  
Natural Rubber Composites ◽  
Fiber Treatment ◽  
Cure Time

Sisal fiber/natural rubber (NR) composites were prepared by the incorporation of sisal fiber into NR at contents of 10-30 phr. Fiber treatment (alkalization) and adding maleic anhydride grafted natural rubber (NR-g-MA) were used to improve interfacial adhesion between sisal fiber and NR matrix. Mechanical properties, morphologies, and cure characteristics of the composites were studied. With increasing fiber content, modulus at 100% strain (M100), modulus at 300% strain (M300), and hardness of the composites increased whereas tensile strength and elongation at break decreased. Cure time of the composites decreased with increasing fiber content but scorch time was not much affected by fiber content. Alkali treated sisal fiber/NR composite exhibited higher tensile properties and hardness than untreated sisal fiber/NR composite at all fiber content due to the improved adhesion between fiber and NR matrix through the mechanical interlocking mechanism. Alkalization showed no effect on scorch time and cure time of the composites. The addition of NR-g-MA into the composites increased M100, M300, tensile strength, and hardness but prolonged scorch time and cure time. NR-g-MA provided more effective improvement of the mechanical properties of the composites when compared to fiber alkalization.

Sign in / Sign up

Export Citation Format

Share Document