The Influence of Complex Dynamic Phenomena Caused by Wind Action on Behaviour of Transportation Pipelines

2013 ◽  
Vol 837 ◽  
pp. 170-174
Author(s):  
Gheorghe Pintilie
Keyword(s):  
Wind Speed ◽  
Aerodynamic Force ◽  
Mathematical Expression ◽  
Periodic Variation ◽  
Operating Conditions ◽  
Frequency Variation ◽  
Wind Action ◽  
Karman Vortex ◽  
Dynamic Phenomena

The main transportation pipelines are subjected to complex stresses resulting from the nature and state of the transported material, the operating conditions, and the environmental factors and so on. Thus, the stress in the pipe wall is generated and influenced by the pressure, the temperature and the mass of the transported fluid, by the weight of the pipe, the ambient temperature and in certain periods of time by the wind speed. In this paper are presented dynamic phenomena generated by wind flow and their effect on the magistrate transportation pipelines. The content of the paper presents an detailed analysis regarding the regimes in which is developing the force generated by Karman vortex and the situation when resonance phenomena are developed. The study presents a mathematical model that describes the dynamic phenomena generated by the wind action, determining the mathematical expression of the aerodynamic force that act on the normal direction to the wind speed. This force is having a periodic variation, its size and the frequency variation is dependent on the wind speed. Some methods are proposed in order to decrease the wind influence on the lifetime of transportation pipelines. The main results of the study are: determination of the speed range for which the dynamic phenomena have a high influence on the pipeline lifetime; determination of the real conditions that can lead to sharp rises of the pipe deformations; determination of the pipeline lifetime reduction under development of dynamic loads.

Simulation and Contrast Analysis of tem Images of Cracks

1990 ◽  
Vol 48 (1) ◽  
pp. 578-579
Author(s):  
D. Goyal ◽  
A. H. King
Keyword(s):  
Displacement Vector ◽  
Crack Tip ◽  
Perfect Crystal ◽  
Operating Conditions ◽  
Displacement Fields ◽  
Fringe Contrast ◽  
Orthogonal Geometry ◽  
Moire Fringe ◽  
Moiré Fringe

TEM images of cracks have been found to give rise to a moiré fringe type of contrast. It is apparent that the moire fringe contrast is observed because of the presence of a fault in a perfect crystal, and is characteristic of the fault geometry and the diffracting conditions in the TEM. Various studies have reported that the moire fringe contrast observed due to the presence of a crack in an otherwise perfect crystal is distinctive of the mode of crack. This paper describes a technique to study the geometry and mode of the cracks by comparing the images they produce in the TEM because of the effect that their displacement fields have on the diffraction of electrons by the crystal (containing a crack) with the corresponding theoretical images. In order to formulate a means of matching experimental images with theoretical ones, displacement fields of dislocations present (if any) in the vicinity of the crack are not considered, only the effect of the displacement field of the crack is considered.The theoretical images are obtained using a computer program based on the two beam approximation of the dynamical theory of diffraction contrast for an imperfect crystal. The procedures for the determination of the various parameters involved in these computations have been well documented. There are three basic modes of crack. Preliminary studies were carried out considering the simplest form of crack geometries, i. e., mode I, II, III and the mixed modes, with orthogonal crack geometries. It was found that the contrast obtained from each mode is very distinct. The effect of variation of operating conditions such as diffracting vector (), the deviation parameter (ω), the electron beam direction () and the displacement vector were studied. It has been found that any small change in the above parameters can result in a drastic change in the contrast. The most important parameter for the matching of the theoretical and the experimental images was found to be the determination of the geometry of the crack under consideration. In order to be able to simulate the crack image shown in Figure 1, the crack geometry was modified from a orthogonal geometry to one with a crack tip inclined to the original crack front. The variation in the crack tip direction resulted in the variation of the displacement vector also. Figure 1 is a cross-sectional micrograph of a silicon wafer with a chromium film on top, showing a crack in the silicon.

Extremely Gusty Winds from a Viewpoint of Aerodynamic Force

2020 ◽  
Author(s):  
Junji Maeda ◽  
Takashi Takeuchi ◽  
Eriko Tomokiyo ◽  
Yukio Tamura
Keyword(s):  
Wind Speed ◽  
Wind Tunnel ◽  
Rise Time ◽  
Aerodynamic Force ◽  
Step Function ◽  
Object Size ◽  
Aerodynamic Forces ◽  
Wind Force ◽  
Wind Observation

To quantitatively investigate a gusty wind from the viewpoint of aerodynamic forces, a wind tunnel that can control the rise time of a step-function-like gust was devised and utilized. When the non-dimensional rise time, which is calculated using the rise time of the gusty wind, the wind speed, and the size of an object, is less than a certain value, the wind force is greater than under the corresponding steady wind. Therefore, this wind force is called the “overshoot wind force” for objects the size of orbital vehicles in an actual wind observation. The finding of the overshoot wind force requires a condition of the wind speed recording specification and depends on the object size and the gusty wind speed.

scholarly journals Experimental performance comparison between circular and elliptical tubes in evaporative condensers

2021 ◽  
Author(s):  
Giuseppe Starace ◽  
Lorenzo Falcicchia ◽  
Pierpaolo Panico ◽  
Maria Fiorentino ◽  
Gianpiero Colangelo
Keyword(s):  
Heat Transfer ◽  
Experimental Approach ◽  
Fluid Dynamic ◽  
Major Axis ◽  
Performance Comparison ◽  
Operating Conditions ◽  
Condensation Temperature ◽  
Air Cooled Condensers ◽  
Reduced Scale ◽  
Dynamic Phenomena

AbstractIn refrigeration systems, evaporative condensers have two main advantages compared to other condensation heat exchangers: They operate at lower condensation temperature than traditional air-cooled condensers and require a lower quantity of water and pumping power compared to evaporative towers. The heat and mass transfer that occur on tube batteries are difficult to study. The aim of this work is to apply an experimental approach to investigate the performance of an evaporative condenser on a reduced scale by means of a test bench, consisting of a transparent duct with a rectangular test section in which electric heaters, inside elliptical pipes (major axis 32 mm, minor axis 23 mm), simulate the presence of the refrigerant during condensation. By keeping the water conditions fixed and constant, the operating conditions of the air and the inclination of the heat transfer geometry were varied, and this allowed to carry out a sensitivity analysis, depending on some of the main parameters that influence the thermo-fluid dynamic phenomena, as well as a performance comparison. The results showed that the heat transfer increases with the tube surface exposed directly to the air as a result of the increase in their inclination, that has been varied in the range 0–20°. For the investigated conditions, the average increase, resulting by the inclination, is 28%.

Studies on Galloping of Iced Conductor Based on Tower-Line Coupling System – Aerodynamic Loads

2012 ◽  
Vol 182-183 ◽  
pp. 1630-1633
Author(s):  
Hao Jun Hu ◽  
Yuan Han Wang ◽  
Zi Dong Hu
Keyword(s):  
Finite Element ◽  
Wind Speed ◽  
Finite Element Model ◽  
Aerodynamic Force ◽  
Element Model ◽  
Aerodynamic Characteristics ◽  
Explicit Integration ◽  
Computing Platform ◽  
Coupling System ◽  
Line Coupling

Based on the second development at the ANSYS computing platform, finite element model of a Tower-Line Coupling system was established. The computational fluid dynamics module (CFX) was used for the numerical simulation of the aerodynamic characteristics of iced conductor. On the basis of the Kaimal spectrum, fast Fourier transform was introduced to prepare the wind speed simulation program WVFS with spatial correlation into consideration, thus generating aerodynamic coefficients of iced conductor at different wind attack angles as well as wind speed time series at tower-line nodes. According to the finite element model of continuous multi-conductors and the aerodynamic force- wind attack angle curve, the explicit integration is applied for numerical solution of galloping of iced conductor.

Prediction of the Flow and Force Characteristics of Safety Relief Valves

2006 ◽  
Author(s):  
W. Dempster ◽  
C. K. Lee ◽  
J. Deans
Keyword(s):  
Operating Conditions ◽  
Cfd Analysis ◽  
Flow Conditions ◽  
Relief Valve ◽  
Good Correspondence ◽  
Geometry Modeling ◽  
Valve Opening ◽  
Satisfactory Prediction ◽  
Force Characteristics

The design of safety relief valves depends on knowledge of the expected force-lift and flow-lift characteristics at the desired operating conditions of the valve. During valve opening the flow conditions change from seal-leakage type flows to combinations of sub-sonic and supersonic flows It is these highly compressible flow conditions that control the force and flow lift characteristics. This paper reports the use of computational fluid dynamics techniques to investigate the valve characteristics for a conventional spring operated 1/4” safety relief valve designed for gases operating between 10 and 30 bar. The force and flow magnitudes are highly dependent on the lift and geometry of the valve and these characteristics are explained with the aid of the detailed information available from the CFD analysis. Experimental determination of the force and flow lift conditions has also been carried out and a comparison indicates good correspondence between the predictions and the experiment. However, attention requires to be paid to specific aspects of the geometry modeling including corner radii and edge chamfers to ensure satisfactory prediction.

Experimental and Theoretical Rotordynamic Characteristics of a Hybrid Journal Bearing

1997 ◽  
Vol 119 (1) ◽  
pp. 132-141 ◽  
Author(s):  
J. T. Sawicki ◽  
R. J. Capaldi ◽  
M. L. Adams
Keyword(s):  
Journal Bearing ◽  
Operating Conditions ◽  
Dynamic Force ◽  
Test Results ◽  
Force Measurements ◽  
Lubrication Equation ◽  
Load Cells ◽  
Theoretical Predictions ◽  
Stiffness And Damping

This paper describes an experimental and theoretical investigation of a four-pocket, oil-fed, orifice-compensated hydrostatic bearing including the hybrid effects of journal rotation. The test apparatus incorporates a double-spool-shaft spindle which permits independent control over the journal spin speed and the frequency of an adjustable-magnitude circular orbit, for both forward and backward whirling. This configuration yields data that enables determination of the full linear anisotropic rotordynamic model. The dynamic force measurements were made simultaneously with two independent systems, one with piezoelectric load cells and the other with strain gage load cells. Theoretical predictions are made for the same configuration and operating conditions as the test matrix using a finite-difference solver of Reynolds lubrication equation. The computational results agree well with test results, theoretical predictions of stiffness and damping coefficients are typically within thirty percent of the experimental results.

Sign in / Sign up

Export Citation Format

Share Document