Effects of SiO2 Substitution on Piezoelectric and Mechanical Properties of PMS-PZT Ternary Piezoelectric Ceramics

2007 ◽  
Vol 280-283 ◽  
pp. 215-218 ◽  
Author(s):  
Zhi Gang Zhu ◽  
Bao Shan Li ◽  
Guo Rong Li ◽  
Qing Rui Yin
Keyword(s):  
Mechanical Properties ◽  
Grain Boundary ◽  
Fracture Strength ◽  
Electromechanical Coupling ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Second Phase ◽  
Rapid Improvement ◽  
Power Application

The effects of SiO2 additives on microstructure, piezoelectric and mechanical properties were investigated for Pb0.98Sr0.02(Mn1/3Sb2/3)0.05Zro.48Ti0.47O3 (PMS-PZT) ternary system close to the morphotropic phase boundary. Piezoelectric coefficient (d33) and electromechanical coupling factor (Kp) considerably deteriorated with the substitution of SiO2 increased. On the other hand, the mechanical quality factor (Qm) increased, the maximum value was 1800. Fracture strength of 1.0 wt% SiO2 added the specimens reached to 106.54 MPa which was about 1.4 times higher than pure PMS-PZT ceramic. The rapid improvement of fracture strength probably due to the decrease of grain size, pore distribute and the second phase (redundant Si4+ ions) segregating on the grain boundary which enhanced the bond energy of grain boundary. The optimized concentration of SiO2 doped PMS-PZT ceramics was 0.4 wt% for high power application: d33 = 300 PC/N, Kp = 0.51, Qm = 1500, tand = 0.32% and the fracture strength was 88.5MPa.

Effects of Zn/Ni Ratio and Doping Material on Piezoelectric Characteristics of Pb((Zn, Ni)1/3Nb2/3)O3–Pb(Zr, Ti)O3 Ceramics

2020 ◽  
Vol 12 (2) ◽  
pp. 237-243
Author(s):  
So Won Kim ◽  
Yong Jeong Jeong ◽  
Hee Chul Lee
Keyword(s):  
Quality Factor ◽  
Electromechanical Coupling ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Molar Ratio ◽  
Pzt Ceramics ◽  
Composition Ratio ◽  
Columbite Precursor ◽  
Piezoelectric Characteristics

This study investigates the effects of the Zn/Ni composition ratio and doping materials on the piezoelectric properties of PZNN-PZT ceramics for the fabrication of piezoelectric ceramics with excellent characteristics. A soft relaxor was used to improve the electrical characteristics and sinterability. The ceramics were fabricated with a base composition ratio of 0.13Pb((Zn1–xNix)1/3Nb2/3)O3–0.87Pb(Zr0.5Ti0.5)O3. The columbite phase was formed by reacting NiO and Nb2O5, which have low reactivity, as the first calcination, and the columbite precursor method was applied for the second calcination with PbO. Although the pellet was produced by sintering at a relatively low temperature of 950 °C, we obtained a dense ceramic with a high density of 7.9 g/cm3 . To improve the quality factor in the composition with a Ni/(Ni + Zn) molar ratio of 0.1, the doping materials MnO2, Fe2O3, CuO, and Bi2O3 were added and their properties were confirmed. Pure perovskite phases were formed in the ceramics of all compositions and doping materials. In particular, the PZNN-PZT ceramics doped with 0.3 wt% MnO2 showed a piezoelectric coefficient of 348 pC/N, electromechanical coupling factor of 0.59, mechanical quality factor of 345, and Curie temperature of 316 °C, which are excellent piezoelectric characteristics.

(1-x)(K0.475Na0.475Li0.05)(Nb0.975Sb0.025)O3-xBiFeO3 Lead-Free Piezoelectric Ceramics with CuO Sintering Aid

2011 ◽  
Vol 687 ◽  
pp. 228-232
Author(s):  
Yong Jie Zhao ◽  
Yu Zhen Zhao ◽  
Rong Xia Huang ◽  
Rong Zheng Liu ◽  
He Ping Zhou
Keyword(s):  
Electrical Properties ◽  
Electromechanical Coupling ◽  
Piezoelectric Materials ◽  
Piezoelectric Ceramics ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Lead Free ◽  
X Ray Diffraction ◽  
Diffraction Patterns

(1-x) (K0.475Na0.475Li0.05)(Nb0.975Sb0.025)O3-xmolBiFeO3 (x=0, 0.002, 0.004, 0.006, 0.008) doped with 0.8mol%CuO lead-free piezoelectric ceramics were prepared by the solid state reaction technique. X-ray diffraction patterns suggested that all the ceramics presented perovskite structure. The compositional dependence of the phase structure and the electrical properties of the ceramics were studied. The ceramic (x=0.002) near room temperature exhibited excellent electrical properties (piezoelectric constant d33=172pC/N, planar electromechanical coupling factor kp=0.43, and dielectric constant =418). A relatively high mechanical quality factor (Qm=200) was also obtained in this particular composition. All these results revealed that this system might become a promising candidate for lead-free piezoelectric materials.

Investigation on Electrical Properties of CaCu3Ti4O12-Modified (Na,Bi)TiO3-BaTiO3 Lead Free Piezoceramics

2014 ◽  
Vol 887-888 ◽  
pp. 289-293
Author(s):  
Jing Chang Zhao ◽  
Zhen Lai Zhou
Keyword(s):  
Electrical Properties ◽  
Electromechanical Coupling ◽  
Piezoelectric Properties ◽  
Piezoelectric Ceramics ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Lead Free ◽  
Lead Free Ceramics ◽  
Structure Morphology

(Na,Bi)TiO3-BaTiO3lead free piezoelectric ceramics were fabricated with modification of CaCu3Ti4O12additives. The phase structure, morphology, dielectric and piezoelectric properties of prepared samples were investigated, respectively. It was found that CaCu3Ti4O12additives evidently improve the polarization properties of (Na,Bi)TiO3-BaTiO3lead free ceramics and the obtained samples exhibit an excellent piezoelectric properties (electromechanical coupling factorKp=31%, mechanical quality factorQm=151 and piezoelectric constantd33=160pC/N). According to results, the effect of CaCu3Ti4O12additives on electrical properties of (Na,Bi)TiO3-BaTiO3lead free piezoelectric ceramics is discussed.

Improvement of Electromechanical Coupling Factor and Mechanical Quality Factor in PZT-PMN Ceramics by MnO2 Addition

2009 ◽  
Vol 421-422 ◽  
pp. 381-384
Author(s):  
Rungnapa Tipakontitikul ◽  
Amporn Kamonlert ◽  
Sukum Eitssayeam ◽  
Anuson Niyompan
Keyword(s):  
Electromechanical Coupling ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Tetragonal Symmetry ◽  
X Ray Diffraction ◽  
Ceramic Structure ◽  
Mechanical Quality ◽  
Conventional Sintering ◽  
Sintering Method

PZT-PMN ceramic system with presence of MnO2 contents were proposed and prepared using conventional sintering method as for piezoelectric transformer application. Phase formation and several dielectric and piezoelectric parameters were studied as a function of MnO2 concentration. The x-ray diffraction study revealed the tetragonal symmetry for all samples with MnO2 doping. To determine polarization, the P-E hysteresis loop were produced and the results indicated that entering of Mn4+ ions in the ceramic structure created large amount of oxygen vacancies and the consequent was observed as displacement of the loops to E axis. The obtained optimum parameter are d33 = 119 pC/N, kp = 0.207, Qm = 1669, tan = 0.0101, Pr = 20 μm/cm2 and Ec = 10 kV/cm.

Fabrication and Properties of 1-3-2 Piezoelectric Composites

2010 ◽  
Vol 123-125 ◽  
pp. 77-80
Author(s):  
Shi Feng Huang ◽  
Dong Yu Xu ◽  
Jun Chang ◽  
Ya Mei Liu ◽  
Xin Cheng
Keyword(s):  
Piezoelectric Ceramic ◽  
Electromechanical Coupling ◽  
Volume Fraction ◽  
Functional Materials ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Piezoelectric Composites ◽  
Mechanical Quality ◽  
Planar Electromechanical Coupling Factor

In this paper, the 1-3-2 piezoelectric composites were fabricated by the cut-filling technique using P(MN)ZT piezoelectric ceramic as functional materials and polymer as matrix. The effects of ceramic volume fraction on the electrical properties of the composites were studied. The results indicate that as the ceramic volume fraction increases, the piezoelectric stain factor d33 increases evidently, while the piezoelectric voltage factor g33 decreases. Besides, the planar electromechanical coupling factor Kp and mechanical quality factor Qm of the composite are also less than those of the pure ceramic, while the thickness electromechanical coupling factor Kt is larger than that of the ceramic.

scholarly journals Microstructure and Piezoelectricity of (Na,K,Li)(Nb,Sb)O3–(Bi,Na)(Sr)ZrO3–BaZrO3 Ceramics

Crystals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 868
Author(s):  
Juhyun Yoo ◽  
Jonghyun Lee
Keyword(s):  
Physical Properties ◽  
Piezoelectric Actuator ◽  
Electromechanical Coupling ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Low Loss ◽  
Mechanical Quality ◽  
Li Substitution ◽  
Sintering Method

In this paper, (Na,K)1−xLi.x(Nb,Sb)O3–(Bi,Na)(Sr)ZrO3–BaZrO3 ceramics were fabricated with x(= Li) substitution by two-step sintering method, and their physical characteristics were investigated. When Li substitution was added to the ceramics, piezoelectric constant (d33) and electromechanical coupling factor (kp) were rapidly reduced. However, mechanical quality factor (Qm) was enhanced. For the KNN-BNZ((K,Na)(Nb)O3–(Bi,Na)(Sr)ZrO3) ceramics with Li(x) = 0 substitution, the best physical properties of d33 = 300 [pC/N], kp = 0.40, Qm = 33 and dialectic constant (εr) = 2430 were shown, respectively. Additionally, the KNN-BNZ ceramics with Li(x) = 0.02, the d33 of 246[pC/N], the kp of 0.37, the Qm of 42 and the εr of 2090 appeared, which were suitable for the low-loss piezoelectric actuator.

SYNTHESIS AND PIEZOELECTRIC PROPERTIES OF (Ba1-xCax)(Ti1-yZry)O3 BY A NOVEL COMPOSITE-HYDROXIDE-MEDIATED APPROACH

2012 ◽  
Vol 05 (02) ◽  
pp. 1260013
Author(s):  
TAKESHI KIMURA ◽  
SHU YIN ◽  
TAKATOSHI HASHIMOTO ◽  
ATUSHI SASAKI ◽  
YUICHI TOKANO ◽  
...  
Keyword(s):  
High Purity ◽  
Electromechanical Coupling ◽  
Piezoelectric Properties ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Narrow Size Distribution ◽  
Mechanical Quality ◽  
Average Size ◽  
Quality Factor Q

High purity ( Ba 1-x Ca x)( Ti 1-y Zr y) O 3((x,y)=(0.00,0.00)–(0.50,0.50)) were synthesized by a composite-hydroxide-mediated approach at 200°C using a sealed tube with a rolling system. The powders with an average size of 50 nm in diameter and narrow size distribution were produced. The highest electromechanical coupling factor k r was 36.1% ((x,y) = (0.05,0.03)) and highest mechanical quality factor Q m was 256 ((x,y) = (0.11,0.13)).

Piezoelectric Behavior Based on Mixing-Doped in Lead Zirconate Titanate Ceramics and Application

2011 ◽  
Vol 189-193 ◽  
pp. 4126-4129
Author(s):  
Bing Huei Chen ◽  
Long Wu
Keyword(s):  
Lead Zirconate Titanate ◽  
Electromechanical Coupling ◽  
Piezoelectric Properties ◽  
Electromechanical Coupling Factor ◽  
Lead Zirconate ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Ceramic Technology ◽  
Zirconate Titanate ◽  
Cation And Anion Vacancies

In this investigation, we extend our previous works to improve piezoelectric properties of Pb(Zr,Ti)O3 ceramics. Modified lead zirconate titanate (PZT) piezoceramics with a composition Zr/Ti=53/47 containing a trace of mixing dopants were prepared by conventional ceramic technology sintering powder compacts. Replacement of (Zr, Ti)+4 by Nb+5, Pb+2 by Sb+3 and Mn+4 in PZT perovskite type solid solutions was accomplished by the creation of cation and anion vacancies. Modified ceramics were explored as a function of firing temperature to acquire exceedingly good piezoelectric characterizations. From the analysis results, calcined at 850°C for 2 h, and then sintered at 1280°C for 2 h, PZT piezoceramic showed the larger dielectric constant er 2013, mechanical quality factor Qm 120 and maximum electromechanical coupling factor kp 0.67. Besides, the bulk ceramic grains distribution were found to be uniform. Furthermore, the sample was found to possess piezoelectric properties, the resonance frequency being about 200 KHz suitable for acoustic sensor.

Electrical and Optical Properties of Potassium Niobate Grown by Vertical Bridgman Method

2006 ◽  
Vol 301 ◽  
pp. 15-18 ◽  
Author(s):  
Takashi Takagi ◽  
Takashi Fujii ◽  
Akira Ando ◽  
Yukio Sakabe
Keyword(s):  
Electromechanical Coupling ◽  
Wavelength Region ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Bridgman Method ◽  
Optical Absorption Coefficient ◽  
Potassium Niobate ◽  
Vertical Bridgman Method ◽  
Vertical Bridgman

Piezoelectric properties of potassium niobate (KNbO3; KN) crystal grown using the Vertical Bridgman method were obtained by a resonance-antiresonance method for a length extensional mode. The crystal was poled at 200°C under an electric field of 70 V/mm applied parallel to one of the spontaneous polarization axes. An electromechanical coupling factor (k31) of 0.248, mechanical quality factor (Qm) of 5700, piezoelectric constant (d31) of 9.6 pC/N, elastic compliance (s11E) of 4.02 pm2/ N, and constant (e33T/e0) of 42 were obtained. The optical absorption coefficient of poled crystal has been less than 1.0 cm-1 in the wavelength region of 400-1600 nm. Comparing these values with the reported one for TSSG-KN, indicated that our VB-KN was of good quality.

Study on Properties of NiO-Doping PMSZT Piezoelectric Ceramics Sintered at Low Temperature

2012 ◽  
Vol 487 ◽  
pp. 770-774
Author(s):  
Wei Ye Chen ◽  
Lan Zhu ◽  
Peng Yi Liu ◽  
Cai Ping Lin ◽  
Hao Jian Tu
Keyword(s):  
Electromechanical Coupling ◽  
Piezoelectric Properties ◽  
Rhombohedral Phase ◽  
Electromechanical Coupling Factor ◽  
Coupling Factor ◽  
Mechanical Quality Factor ◽  
Doping Amount ◽  
Pure Perovskite Structure ◽  
Mechanical Quality ◽  
Quality Factor Q

The effects of NiO-doping on the microstructure and piezoelectric properties of PMSZT ceramics were investigated. The experimental results indicate that pure perovskite structure was obtained in the doping range. With the increasing of doping amounts, phases shift from tetragonal phase to rhombohedral phase. The mechanical quality factor (Qm) , Dielectric constant (εr) , electromechanical coupling factor (Kp) and piezoelectric constant (d33) increase with the increasing of doping amounts and then decrease, whereas, dielectric loss (tanδ) decrease and then increase. The ceramics with doping amount of 0.1wt.% sintered at 980 °C have the optim properties of Qm=1345, εr=1853, Kp=0.62, d33=375 and tanδ=0.21%。

Sign in / Sign up

Export Citation Format

Share Document