Roll Casting of Three Layers Clad Strip

2010 ◽  
Vol 443 ◽  
pp. 128-133 ◽  
Author(s):  
Ryoji Nakamura ◽  
Masakazu Sawai ◽  
Ryoji Nakamura ◽  
Takanori Yamabayashi ◽  
Shinji Kumai ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Cold Rolling ◽  
Molten Metal ◽  
Casting Speed ◽  
Roll Casting ◽  
Continuous Bending ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Twin Roll

A roll caster, which could cast the three layers of clad strip directly from the molten metal, was designed, assembled and tested. The base strip was AA3003 aluminum alloy and overlay strips were AA4045 aluminum alloy. An unequal diameter twin roll caster was modified to cast clad strip. Two small rolls were amounted on a large roll. A scraper plate was used to prevent the mixture of the different kinds of melts. The casting of three strips and the connecting of strips could be operated by one roll caster. The interfaces between the strips were clear, and the mixture of the melt did not occur. The clad strip could be cold rolled without the annealing. The clad strip did not peel at connecting surface by the cold rolling and continuous bending. The strips were connected strictly. The casting speed was 20m/min, and this speed was much higher than the casting speed of the conventional twin roll caster for aluminum alloys.

Roll Casting of Al-25mass%Si

2010 ◽  
Vol 97-101 ◽  
pp. 1057-1060 ◽  
Author(s):  
Ryoji Nakamura ◽  
Masayuki Saito ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminum Alloy ◽  
Casting Speed ◽  
Alloy Strip ◽  
Thickness Direction ◽  
Near Surface ◽  
Roll Casting ◽  
Eutectic Si ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Twin Roll

Roll casting of Al-25mass%Si hyper eutectic aluminum alloy strip was tried by an unequal diameter twin roll caster. The casting speed was 10m/min. The thickness of the strip was about 2mm. The eutectic Si and primary crystallized Si were very fine by the effect of the rapid solidification. The size of the primary crystallized Si was not uniform at the thickness direction. The primary crystallized Si at the near surface was finer than that of inside. The eutectic Si was finer than 2μm. The strip could be cold rolled after hot rolling and annealing.

Roll Casting of Al-40%Sn-1%Cu Strip

2018 ◽  
Vol 382 ◽  
pp. 147-154
Author(s):  
Toshio Haga ◽  
Ryusuke Onishi ◽  
Hisaki Watari ◽  
Shinichi Nishida
Keyword(s):  
Aluminum Alloy ◽  
Molten Metal ◽  
Solidification Time ◽  
Roll Speed ◽  
Strip Surface ◽  
Sliding Bearings ◽  
Roll Casting ◽  
Twin Roll Caster ◽  
Metal Microstructure ◽  
Twin Roll

Strip casting of Al-40%Sn-1%Cu, which is an aluminum alloy used for sliding bearings, was attempted using an unequal diameter twin roll caster. The conditions required to cast sound strips, including the roll speed, molten temperature, roll load, solidification length, melt head, and use of an upper plate, were investigated. The roll load required to make a stable strip surface was 0.01 kN/mm, and the porosity was minimum when the solidification time was less than 0.6 s. The solidification time was controlled by the roll speed and the solidification length. The casting temperature must be set below 670°C to properly solidify the molten metal, and the metal microstructure became finer as the melt head decreased.

Casting of Clad Strip by an Unequal Diameter Twin Roll Caster

2010 ◽  
Vol 638-642 ◽  
pp. 413-418 ◽  
Author(s):  
Ryoji Nakamura ◽  
Masakazu Sawai ◽  
Ryoji Nakamura ◽  
H. Watari ◽  
S. Kumai
Keyword(s):  
Cold Rolling ◽  
Molten Metal ◽  
Continuous Bending ◽  
Twin Roll Caster ◽  
Twin Roll

An unequal diameter twin roll caster which can cast clad strips was devised and assembled. The casting of the clad strip was tried, and fabrication of the clad strip was attained. This twin roll caster was planned for the process saving. The clad strip was assembled directly from AA3003 molten metal and AA4045 molten metal at speed of 20m/min. The Si-diffusion-area between the strips was very narrow, and the interface between the strips was clear. The strips were bonded firmly. The strips were not pealed by the cold rolling and the continuous bending.

Roll Casting of 400 mm Width Al-40%Sn-1%Cu Clad Strip

2017 ◽  
Vol 904 ◽  
pp. 3-8 ◽  
Author(s):  
Toshio Haga ◽  
Kento Ikeda ◽  
Takafumi Nakano
Keyword(s):  
Aluminum Alloy ◽  
Contact Condition ◽  
Molten Metals ◽  
Full Contact ◽  
Roll Casting ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Twin Roll

A 400 mm width of clad strip consisting of Al-40%Sn-1%Cu and 1070 aluminum alloy could be cast directly from molten metals at a speed of 10 m/min by an unequal diameter twin roll caster equipped with a scraper. An interface clearly existed between the two strips of the clad strip. As-cast clad strip could be cold rolled down to 1 mm without peeling at the interface. The as-cast clad strip could also be bent in the full contact condition without peeling at the interface.

Casting of Aluminum Alloy Bar by Semisolid Roll Casting

2008 ◽  
Vol 141-143 ◽  
pp. 295-300 ◽  
Author(s):  
Ryoji Nakamura ◽  
T. Asai ◽  
Hisaki Watari ◽  
Shinji Kumai
Keyword(s):  
Aluminum Alloy ◽  
Casting Speed ◽  
Semisolid Slurry ◽  
Primary Crystal ◽  
Cooling Slope ◽  
Roll Casting ◽  
Twin Roll Caster ◽  
Twin Roll

Rheo-casting of 4045 aluminum alloy bar was operated using an unequal diameter twin roll caster and a cooling slope. The semisolid slurry was made by the cooling slope. The thickness of the bar was 12 mm and width was 100mm. The casting speed was 1m/min. Quantity of the melt poured on the cooling slope was important to make sound bar. The primary crystal became spherical, and its size was about 40μm.

Inline Rolling of 5182 Aluminum Alloy Strip Cast by a Vertical Type High Speed Twin Roll Caster

2010 ◽  
Vol 139-141 ◽  
pp. 477-480
Author(s):  
Ryoji Nakamura ◽  
Shuya Hanada ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminum Alloy ◽  
High Speed ◽  
Rolling Speed ◽  
Center Line ◽  
Alloy Strip ◽  
Ripple Mark ◽  
Roll Casting ◽  
Strip Cast ◽  
Twin Roll Caster ◽  
Twin Roll

An inline hot rolling was operated on 5182 aluminum alloy strip cast using a vertical type high speed caster (VHSTRC) at the speed of 60 m/min. A porosity existing at center line of the thickness and a ripple mark on the surface, these are typical defects of the strip cast by the VHSTRC, could be improved by the inline rolling. The rolling speed was as same as the roll-casting-speed of 60m/min. The temperature of the strip, when the inline rolling was operated, was 450oC. The reduction of the strip of the inline rolling was 35%.

Roll Casting and Die Casting of Si-Added Al-Mg Alloy

2020 ◽  
Vol 1007 ◽  
pp. 12-17
Author(s):  
Toshio Haga ◽  
Shinichiro Imamura ◽  
Hiroshi Fuse ◽  
Hisaki Watari ◽  
Shinichi Nishida
Keyword(s):  
High Speed ◽  
Die Casting ◽  
Sheet Forming ◽  
Mg Alloy ◽  
Tension Tests ◽  
Roll Casting ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Si Content ◽  
Twin Roll

Si ranging from 0.2 mass% to 2.0 mass% was added to Al-5%Mg alloy (5182) and strip was cast by a vertical type high-speed twin-roll caster at a speed of 80 m/min. The as-cast strip was cold-rolled down to 1 mm thickness and annealed. The mechanical properties were investigated using cup tests and tension tests. The limiting draw ratio (LDR) of the 5182 alloy was 2.0 and the LDR became smaller as the Si content increased. When the Si content was 2.0 mass%, the LDR was 1.8, which shows that Si-added 5182 can be used for sheet forming, if the Si content is less than 2.0 mass%. The tensile strength and elongation were almost constant when the Si content was less than 1 mass%, but decreased at 2.0 mass% Si. However, the elongation was greater than 20% at 2.0 mass% Si. For die casting, 2.0 mass% Si was determined as the appropriate content from the results of the tension tests. When the Si content is in the range from 1.0 mass% to 2.0 mass%, then the Si added Al-5%Mg has the ability to be used for both die casting and sheet forming.

High Speed Twin-Roll Casting of Al-Mg Alloys

2010 ◽  
Vol 154-155 ◽  
pp. 1544-1548 ◽  
Author(s):  
Kosuke Komeda ◽  
Ryoji Nakamura ◽  
Shinji Kumai
Keyword(s):  
Heat Transfer ◽  
Aluminum Alloy ◽  
High Speed ◽  
Aluminum Alloy 5182 ◽  
Roll Casting ◽  
Twin Roll Caster ◽  
Deep Drawing Test ◽  
Study Heat Transfer ◽  
Twin Roll ◽  
Steel Rolls

The disadvantages of the conventional twin-roll caster for aluminum alloy are low casting speeds and limited choices of alloys that are castable by this processing. It is known that strip casting of aluminum alloy 5182 is very difficult because of their wider freezing zones. The vertical-type high-speed twin-roll caster used in the present study was devised to overcome these disadvantages. Features of the high speed twin roll casters are as below. Mild steel rolls were used in order to increase the casting speed and to be made at a lower equipment cost. Roll coating is produced in casting of Al-Mg alloy. Therefore lubricant, that resists heat transfer, was not used in the present study. Heat transfer between melt and the roll was improved by hydrostatic pressure of the melt. Low superheat casting was carried out in order to improve microstructure of the strip. In the present study, effectiveness of a high-speed twin roll caster for recycling aluminum alloy was investigated. The effects of the high-speed twin roll caster on alleviating the deterioration of mechanical properties by impurities were investigated. Properties of the cast strip were investigated by metalography, a tension test, and a deep drawing test.

Aluminum Alloy Strips Casting Using an Unequal Diameter Twin Roll Caster

2004 ◽  
Vol 449-452 ◽  
pp. 145-148 ◽  
Author(s):  
Ryoji Nakamura ◽  
Kenta Takahashi ◽  
Masahiko Ikawa
Keyword(s):  
Aluminum Alloy ◽  
Casting Speed ◽  
Increase Productivity ◽  
Twin Roll Caster ◽  
Semisolid Casting ◽  
Twin Roll ◽  
Low Superheat

An unequal diameter twin roll caster was devised in order to increase productivity of the strip. This caster could cast the strip thicker than 6mm at the speed of 5m/min. The feature of this caster is that the lower roll was four times larger than the upper roll. The solidification length of the strip could be set longer easily than the conventional twin roll caster for aluminum alloy. Lowsolidification rate semisolid casting and low superheat casting were adopted. These were effective to increase the casting speed without decreasing the thickness of the strip. In the present study, the unequal diameter twin roll caster was designed and assembled. The test castings were operated and the characteristics of this caster were shown.

Roll Casting of Al-SiCp Strip

2011 ◽  
Vol 675-677 ◽  
pp. 811-814 ◽  
Author(s):  
Toshio Haga ◽  
Teppei Nakamura ◽  
S. Kumai ◽  
H. Watari
Keyword(s):  
Hot Rolling ◽  
High Speed ◽  
Strip Casting ◽  
Cast Strip ◽  
Fine Grain ◽  
Roll Casting ◽  
Speed Up ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
Twin Roll

The strip casting of Al-SiCp alloy was operated by a high speed twin roll caster. The content of SiCp was 20Vol% and 30Vol%. Both of Al-20Vol%SiCp and Al-30Vol%SiCp strips could be cast continuously at the speed up to 90m/min. The SiCp particle distributed uniformly. This was the effect of fine grain of the strip. The as-cast strip of Al-20Vol%SiCp could be cold rolled after homogenization. The as-cast strip of Al-30Vol%SiCp could be cold rolled after once hot rolling and annealing. The as-cast strip of Al-20Vol%SiCp could be coiled at the diameter of 460mm.

Sign in / Sign up

Export Citation Format

Share Document