Parametric Generation of Random Distribution of Fibers in Long-Fiber Reinforced Composites and Micromechanical FE Analysis

2010 ◽  
Vol 452-453 ◽  
pp. 117-120
Author(s):  
Zhen Qing Wang ◽  
Xiao Qiang Wang ◽  
Ji Feng Zhang ◽  
Song Zhou
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Fiber Volume Fraction ◽  
Random Distribution ◽  
Volume Fraction ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Parametric Generation ◽  
High Fiber ◽  
Damage Initiation

A method for the parametric generation of the transversal cross-section microstructure model of unidirectional long-fiber reinforced composite (LFRC) is presented in this paper. Meanwhile, both the random distribution of the fibers and high fiber volume fraction are considered in the algorithm. The fiber distribution in the cross-section is generated through random movements of the fibers from their initial regular square arrangement. Furthermore, cohesive zone element is introduced into modeling the interphase between the fiber and the matrix. All these processes are carried out by the secondary development of the finite element codes (ABAQUS) via Python language programming. Based on the model generated, micromechanical finite element analysis (FEA) is performed to predict the damage initiation and subsequent evolution of the composites. The results show that this technique is capable of capturing the random distribution nature of these composites even for high fiber volume fraction. Moreover, the results prove that a good agreement with the experimental results is found.

A Novel Model for Predicting the Thermal Conductivity of Fiber Reinforced Ceramic Materials

2014 ◽  
Vol 936 ◽  
pp. 154-163
Author(s):  
Rui Xu ◽  
Jun Kui Mao ◽  
Jing Yu Zhang ◽  
De Cang Lou ◽  
Wen Guo
Keyword(s):  
Thermal Conductivity ◽  
Volume Content ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Good Precision ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
High Fiber ◽  
Novel Model ◽  
Thermal Conductivities

The prediction of fiber reinforced ceramic is one of the most important procedure when investigating the application of ceramic composite. Numerical simulations were applied and a novel model was brought out in this paper. Firstly, four different models for predicting thermal conductivities of unidirectional fiber reinforced materials were compared, which include the Rayleigh,LN,ST and TE model,. It shows that Rayleigh model and LN model have good precision only in low fiber volume content cases. There existed big differences between the experimental and numerical results if predicted the high fiber volume content with either these four models. Then a novel model based on LN model was studied with the correction of the representative volume element method. Further comparison results indicate that the error can be reduced as 55.6% with this novel model. At the same time, the longitudinal (k11) and transverse (k22) thermal conductivities predicted by the novel model were also analyzed. It was found thatk11had a linear relationship with fiber volume fraction and thermal conductivity ratio (p). Butk22had a nonlinear relationship with fiber volume fraction, which increased much greatly when fiber volume fraction increasing at high fiber volume fraction andp>1.

Finite Element Analysis of Interfacial Debonding Damage in Fiber-Reinforced Ceramic Matrix Composites

2007 ◽  
Vol 546-549 ◽  
pp. 1555-1558
Author(s):  
Chun Jun Liu ◽  
Yue Zhang ◽  
Da Hai Zhang ◽  
Zhong Ping Li
Keyword(s):  
Finite Element ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Ceramic Matrix Composites ◽  
Ceramic Matrix ◽  
Interfacial Debonding ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Element Analysis

In this paper the composite fracture process has been simulated via the finite element method. A micromechanics model was developed to predict the stress-strain response of a SiO2f/ SiO2 composite explicitly accounting for the local damage mechanisms such as fiber fracture and interfacial debonding. The effects of interfacial strength and fiber volume fraction on the toughness of fiber-reinforced ceramic matrix composites were investigated. The results showed that the composite failure behaviors correlated with the interface strength, which could achieve an optimum value for the elevation of the composite toughness. The increase of fiber volume fraction can make more toughening contributions.

Manufacture of Fabric Reinforced Thermoplastic Composites with High Fiber Volume Fraction

2013 ◽  
Vol 796 ◽  
pp. 301-305
Author(s):  
An Chang Xu ◽  
Li Min Bao
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Thermoplastic Composite ◽  
Thermoplastic Composites ◽  
Impregnation Method ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
High Fiber ◽  
Molding Method ◽  
Reinforcement Fiber

In fiber reinforced thermosetting plastic (FRP) the fiber volume fraction is always up to 60 percent, but in fiber reinforced thermoplastic (FRTP) it is low to about 30 percent which greatly limit their performance. In this paper, for increasing the fiber volume fraction of thermoplastic composite, a new impregnation method for molding continuous fiber reinforced thermoplastic was explored; the fiber volume fraction was significantly raised to 60 percent which is equal to that of FRPs. Then the tensile property was investigated and made a contrast with FRP with the same reinforcement fiber. The results showed that both the FRP and FRTP composites have the similar tensile properties and indicated that the molding method is effective for FRTP manufacture.

Fabrication of short SiC fiber reinforced SiC matrix composites with high fiber volume fraction

2016 ◽  
Vol 109-111 ◽  
pp. 1174-1178 ◽  
Author(s):  
Joon-Soo Park ◽  
Hiroshi Nishimura ◽  
Daisuke Hayasaka ◽  
Ju-Hyeon Yu ◽  
Hirotatsu Kishimoto ◽  
...  
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
High Fiber ◽  
Sic Fiber

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Sign in / Sign up

Export Citation Format

Share Document