Preparation of TiB2-TiN and TiN-B Powders and their Processing

2012 ◽  
Vol 527 ◽  
pp. 32-37
Author(s):  
J. Grabis ◽  
Ints Šteins ◽  
Dz. Rašmane
Keyword(s):  
Grain Size ◽  
Relative Density ◽  
Grain Growth ◽  
Spark Plasma Sintering ◽  
Amorphous Boron ◽  
Reactive Sintering ◽  
Plasma Technique ◽  
Sintering Time ◽  
Plasma Sintering ◽  
Spark Plasma

TiN and TiN/TiBSubscript text2 nanoparticles with crystallite size of TiN in the range of 27–38 nm and TiBSubscript text2 in the range of 55–90 nm have been prepared by thermal plasma technique. The prepared nanoparticles and mechanical mixture of TiN with amorphous boron have been densified using spark plasma sintering and the microstructure and density of the samples were compared. The relative density of the samples with content of TiBSubscript text2 about 36 wt.% is in the range of 95.9–97.1% in dependence on the precursors. The higher relative density of the samples provided reactive sintering of TiN/B powder. The grain size of the composites in the range of 0.5–3 µm testified that spark plasma sintering intensified the grain growth in despite of the short sintering time.

Research on Two Sintered Techniques of Nanometer WC-Co Powder

2007 ◽  
Vol 534-536 ◽  
pp. 593-596 ◽  
Author(s):  
Lan Sun ◽  
Cheng Chang Jia ◽  
Hua Tang
Keyword(s):  
Grain Size ◽  
Grain Growth ◽  
Spark Plasma Sintering ◽  
Hot Pressing ◽  
Sintering Temperature ◽  
Grain Sizes ◽  
Sintering Time ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Hot Pressing Sintering

This paper concerned with SPS (spark plasma sintering), hot pressing of sinter nanometer WC-Co powder and discussed the density, hardness, microstructures and grain sizes of the alloys sintered by different styles. The results showed that SPS could lower the sintering temperature, increased the density and circumscribed the growth of grain size of WC. Hot pressing sintering could produce high density alloys and play well on the grain growth, but its sintering temperature and sintering time were larger than SPS. Besides, the hardness of the sintered cemented alloys that was dependent on the grain size and densification could also be improved by SPS and hot pressing.

Reactive Spark Plasma Sintering of B-C-Ti-N Powders

2014 ◽  
Vol 604 ◽  
pp. 165-168
Author(s):  
Janis Grabis ◽  
Ints Steins ◽  
Aloizijs Patmalnieks ◽  
Inta Sipola
Keyword(s):  
Phase Composition ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Carbon Nanoparticles ◽  
Molar Ratio ◽  
Amorphous Boron ◽  
Reactive Sintering ◽  
Plasma Sintering ◽  
Spark Plasma

The TiB2-TiN0.1 C0.9 and B4C-TiB2 composites with relative density of 95.7-98.6% were manufactured by SPS reactive sintering mixtures of amorphous boron with TiN or TiNC and carbon nanoparticles at 1700 °C and pressure of 30 MPa during 10 min. The phase composition of the materials was determined in dependence on molar ratio of Ti/B and B/C.

NdFeB Type Magnets Produced by Spark Plasma Sintering

2014 ◽  
Vol 802 ◽  
pp. 585-589 ◽  
Author(s):  
M. Alberteris Campos ◽  
N. Vicente ◽  
I.F. Machado ◽  
K.S.T. de Souza ◽  
D. Rodrigues ◽  
...  
Keyword(s):  
Grain Size ◽  
Grain Growth ◽  
Spark Plasma Sintering ◽  
Alloying Element ◽  
Consolidation Process ◽  
Ndfeb Magnets ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Typical Temperature

The shortage of dysprosium as an alloying element has directed the research on the grain size refining of NdFeB, since higher coercivities can be obtained by decreasing the grain size, without Dy addition. The Spark Plasma Sintering (SPS) is a consolidation process which allows densification at lower temperatures and shorter dwell times of sintering, thus avoiding the grain growth. Therefore, the typical temperature of sintering of NdFeB magnets can be decreased from 1050°C to around 800°C, as it was evidenced by means of SPS shrinkage curves and the high densified microestructure obtained in this work.

Effect of Alumina Additions on Mechanical and Electrical Properties of 8mol% Yttria-Stabilized Zirconia Prepared by Spark Plasma Sintering

2006 ◽  
Vol 317-318 ◽  
pp. 917-920
Author(s):  
Jae Kwang Kim ◽  
Kyung Hun Kim ◽  
Yong Ho Choa ◽  
Jong Won Yoon ◽  
Kwang Bo Shim
Keyword(s):  
Electrical Conductivity ◽  
Grain Size ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Average Particle Size ◽  
Yttria Stabilized Zirconia ◽  
Average Particle ◽  
Stabilized Zirconia ◽  
Plasma Sintering ◽  
Spark Plasma

Dense 8mol% yttria-stabilized zirconia (8YSZ) consisting of submicrometer-sized grains was prepared using spark plasma sintering (SPS) along with Al2O3 additives. The starting powder with average particle size of 50nm was densified to 98% of the relative density with short sintering time (5min) at 1200 while preserving a submicrometer grain size. The fracture toughness and bending strength showed maximum values of 2.54MPam1/2 and 380MPa at 2vol% alumina-added 8YSZ, due mainly to the higher relative density and small grain size. The electrical conductivity of 2vol% alumina-added 8YSZ was 0.0278 S/cm at 700 in airThus, alumina additions in 8YSZ using the SPS method are an effective process to improve the mechanical strength and electrical conductivity.

Fabrication of Y2Ti2O7 Transparent Ceramic by Spark Plasma Sintering

2021 ◽  
Vol 1035 ◽  
pp. 663-667
Author(s):  
Li Qiong An ◽  
Rong Wei Shi ◽  
Run Hua Fan ◽  
Takashi Goto
Keyword(s):  
Grain Size ◽  
Spark Plasma Sintering ◽  
Pyrochlore Structure ◽  
Transparent Ceramic ◽  
Sintered Body ◽  
Reactive Sintering ◽  
Uniform Microstructure ◽  
Plasma Sintering ◽  
Average Grain Size ◽  
Spark Plasma

Y2Ti2O7 transparent ceramic was fabricated by reactive sintering using spark plasma sintering at 1673 K for 2.7 ks. The sintered body exhibited a cubic pyrochlore structure and uniform microstructure with an average grain size of 2.9 μm. The transmittance reached 73% at a wavelength of 2000 nm after annealing at 1023 K for 21.6 ks.

Grain Growth, Microstructure and Property of Ultrafine WC-Co Alloy by Spark Plasma Sintering

2007 ◽  
Vol 558-559 ◽  
pp. 959-963 ◽  
Author(s):  
Lan Sun ◽  
Cheng Chang Jia ◽  
Min Xian ◽  
Rui Jun Cao
Keyword(s):  
Grain Size ◽  
Grain Growth ◽  
Spark Plasma Sintering ◽  
Abnormal Grain Growth ◽  
Full Density ◽  
Fine Grain ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Increasing Temperature ◽  
New Phase

In order to control WC grain size and get a microstructure with fine grain size during the sintering process, WC grain growth in WC-Co cemented carbide was investigated. The possible reason on the grain growth was showed which includes the normal grain growth (NGG) and the abnormal grain growth (AGG). We adopted the SPS (spark plasma sintering) to sinter nanometer WC-Co powder, the range of temperature was 1100 -1250 °C, the pressure was 40MPa, and sintering time was 5min. In this paper, we discuss the density, hardness, microstructures and grain sizes of the sintered samples. The results showed that during the process sintering WC-Co powder, there are two kinds of growths. XRD investigation of the WC–Co samples spark plasma sintered to full density revealed that no new phase was created. Through the observed microstructure of the sintered samples, we analyzed the reason of the abnormal grain growth of WC grain. The density and hardness of samples were increased with increasing temperature.

Spark Plasma Sintering of Two Commercial Al2O3 Powders

2011 ◽  
Vol 412 ◽  
pp. 336-339 ◽  
Author(s):  
Zhen Hua Liu ◽  
Qin Ma ◽  
Jin Jun Lu
Keyword(s):  
Grain Size ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Average Grain Size ◽  
Spark Plasma

Al2O3 ceramic is prepared by spark plasma sintering (SPS) using two commercial α-Al2O3 powders at elevated sintering temperature. The relative density and average grain size of the prepared Al2O3 ceramics are measured and compared. One α-Al2O3 powder has good sintering property because the relative density of the prepared α-Al2O3 ceramic is higher than 97% while another α-Al2O3 powder has poor sintering property.

scholarly journals Synthesis, microstructure, and properties of high purity Mo2TiAlC2 ceramics fabricated by spark plasma sintering

2020 ◽  
Vol 9 (6) ◽  
pp. 759-768
Author(s):  
Yunhui Niu ◽  
Shuai Fu ◽  
Kuibao Zhang ◽  
Bo Dai ◽  
Haibin Zhang ◽  
...  
Keyword(s):  
Grain Size ◽  
Flexural Strength ◽  
Spark Plasma Sintering ◽  
Layered Structure ◽  
High Purity ◽  
High Fracture Toughness ◽  
Temperature Range ◽  
Microstructure And Properties ◽  
Plasma Sintering ◽  
Spark Plasma

AbstractThe synthesis, microstructure, and properties of high purity dense bulk Mo2TiAlC2 ceramics were studied. High purity Mo2TiAlC2 powder was synthesized at 1873 K starting from Mo, Ti, Al, and graphite powders with a molar ratio of 2:1:1.25:2. The synthesis mechanism of Mo2TiAlC2 was explored by analyzing the compositions of samples sintered at different temperatures. It was found that the Mo2TiAlC2 phase was formed from the reaction among Mo3Al2C, Mo2C, TiC, and C. Dense Mo2TiAlC2 bulk sample was prepared by spark plasma sintering (SPS) at 1673 K under a pressure of 40 MPa. The relative density of the dense sample was 98.3%. The mean grain size was 3.5 μm in length and 1.5 μm in width. The typical layered structure could be clearly observed. The electrical conductivity of Mo2TiAlC2 ceramic measured at the temperature range of 2–300 K decreased from 0.95 × 106 to 0.77 × 106 Ω–1·m–1. Thermal conductivity measured at the temperature range of 300–1273 K decreased from 8.0 to 6.4 W·(m·K)–1. The thermal expansion coefficient (TEC) of Mo2TiAlC2 measured at the temperature of 350–1100 K was calculated as 9.0 × 10–6 K–1. Additionally, the layered structure and fine grain size benefited for excellent mechanical properties of low intrinsic Vickers hardness of 5.2 GPa, high flexural strength of 407.9 MPa, high fracture toughness of 6.5 MPa·m1/2, and high compressive strength of 1079 MPa. Even at the indentation load of 300 N, the residual flexural strength could hold 84% of the value of undamaged one, indicating remarkable damage tolerance. Furthermore, it was confirmed that Mo2TiAlC2 ceramic had a good oxidation resistance below 1200 K in the air.

scholarly journals Microstructure evolution of TC4 powder by spark plasma sintering after hot deformation

2020 ◽  
Vol 39 (1) ◽  
pp. 457-465
Author(s):  
Jiangpeng Yan ◽  
Zhimin Zhang ◽  
Jian Xu ◽  
Yaojin Wu ◽  
Xi Zhao ◽  
...  
Keyword(s):  
Strain Rate ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Hot Deformation ◽  
Tc4 Titanium Alloy ◽  
Weave Structure ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Average Relative Density ◽  
Low Strain Rate

AbstractThe cylindrical samples of TC4 titanium alloy prepared by spark plasma sintering (SPS) were compressed with hot deformation of 70% on the thermosimulation machine of Gleeble-1500. The temperature of the processes ranged from 850°C to 1,050°C, and the strain rates varied between 0.001 and 5 s−1. The relative density of the sintered and compressed samples was measured by the Archimedes principle. During hot deformation, the microstructure of the sample was observed. The results show that the average relative density of the samples was 90.2% after SPS. And the relative density was about 98% after the hot deformation of 70%. Under high temperature (>950°C), the sensitivity of flow stress to temperature was reduced. At low strain rate (0.001 s−1), the increase in the deformation temperature promoted the growth of dynamic recrystallization (DRX). At the same temperature, the increase in strain rate slowed down the growth of DRX grains. And the variation tendency was shown from the basket-weave structure to the Widmanstätten structure at a low strain rate (<0.1 s−1), with increase in the strain rate.

Sign in / Sign up

Export Citation Format

Share Document