Influence of Cutter’s Helix Angle, Workpiece Hardness, Milling Orientation, and MQL in High-Speed Side Milling of AISI D2

2006 ◽  
Vol 532-533 ◽  
pp. 45-48 ◽  
Author(s):  
Asif Iqbal ◽  
Ning He ◽  
Liang Li ◽  
Yu Xia
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Helix Angle ◽  
Workpiece Material ◽  
Side Milling ◽  
Material Hardness ◽  
Aisi D2 ◽  
Coated Carbide

Rapid tool wear is a major demerit of high-speed milling (HSM) applied to cutting of hardened steels, especially the AISI D2. This paper presents an attempt to maximize the tool life by experimentally investigating the effects of cutter’s helix angle, workpiece material hardness, milling orientation, and minimum quantity of lubrication upon tool wear in high-speed side milling of AISI D2, using coated carbide cutters. Effects of these four parameters were studied also upon surface roughness. Statistical analysis upon experimental data revealed that milling orientation was the most significant factor for tool life as well as for surface roughness. The paper also describes the mechanisms of wear undergone by the tools, by making use of SEM photographs and EDS microanalysis. The major wear mechanisms were chipping, adhesion, and diffusion.

Investigation of Tool Wear, Tool Life and Surface Roughness when Machining AISI D2 Hardened Steel Using PVD TiAlN Coated Carbide Tools

2013 ◽  
Vol 465-466 ◽  
pp. 1098-1102 ◽  
Author(s):  
Noor Hakim Rafai ◽  
Mohd Amri Lajis ◽  
N.A.J. Hosni
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tool Life ◽  
Material Removal ◽  
Cutting Tools ◽  
Hardened Steel ◽  
Tool Failure ◽  
Aisi D2 ◽  
Wear Tool ◽  
Coated Carbide

This paper discussed the behavior of cutting tool in terms of tool wear, tool life and surface roughness when machining an AISI D2 hardened steel. An experimental test was conducted at different cutting speeds (Vc) and radial depth of cut (ae) using PVD TiAlN coated carbide tool under dry condition. Tool failure modes and tool wear mechanism for all cutting tools were examined at various cutting parameters. Flank wear was found to be the predominant tool failure for cutting tools. The highest volume material removal (VMR) attained was 3750 mm3 meanwhile the highest tool life (TL) was 9.69 min. The surface roughness (Ra) values from 0.09 to 0.24 μm can be attained in the workpiece with a high material removal. The relationship of tool wear performance and surface integrity was established to lead an optimum parameter in order to have high material removal, maximum tool life as well as acceptable surface finish.

Influence of Tooling Parameters in High-Speed Milling of Hardened Steels

2006 ◽  
Vol 315-316 ◽  
pp. 676-680 ◽  
Author(s):  
Asif Iqbal ◽  
Ning He ◽  
Liang Li ◽  
W.W. Zha ◽  
Y. Xia
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Helix Angle ◽  
Rake Angle ◽  
Milling Process ◽  
Tool Geometry ◽  
Side Milling ◽  
Hardened Steels ◽  
Aisi D2 ◽  
Coated Carbide

Tool life, surface roughness, and cutting forces have always remained extremely important output parameters of milling process. In this paper an attempt has been presented in order to study the influence of cutter geometry and cutter coating upon these three output parameters. Series of high-speed side milling experiments were done upon hardened AISI 4340 and AISI D2 steels using coated and uncoated carbide cutters. Mechanisms of wear occurring in different tools have been described in the paper using SEM photographs and micro-analysis of the tool surface. The analysis of experimental data shows that the coated carbide cutters having high values of helix angle and small values of rake angle, in the negative range, provide the better optimization of highspeed milling of hardened steels. Results imply that tool geometry and coating are influential upon cutting forces and tool wear but not upon surface quality. Introduction of MQL in the process leads the tool to fail abruptly because of the onset of chipping.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

High-Quality End Milling of CFRP – Inclination Milling with High-Helix End Mill –

2016 ◽  
Vol 10 (3) ◽  
pp. 372-380 ◽  
Author(s):  
Akira Hosokawa ◽  
◽  
Naoya Hirose ◽  
Takashi Ueda ◽  
Tomohiro Koyano ◽  
...  
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Surface Integrity ◽  
Helix Angle ◽  
Surface Generation ◽  
End Mill ◽  
Side Milling ◽  
Pull Out ◽  
End Mills ◽  
Coated Carbide

Side milling tests of CFRP (carbon fiber reinforced plastics) containing thermosetting resin are carried out by TiAlN/AlCrN-coated, H2-free DLC (diamond-like carbon)-coated, and CVD diamond-coated carbide end mills without coolant. Two types of end mills having different helix angles of 30° and 60° are used. The film thickness and surface smoothness are varied for the DLC-coated end mills. The cutting characteristics are evaluated by tool wear and surface integrity (i.e., 3D profiles of the machined surface, generation of fluffing, delamination, and pull-out of the carbon fibers). The cutting force and tool flank temperature are also examined for the two types of CFRP composites and the helix angle of the end mill. “Inclination milling,”in which the end mill is tilted so that the resultant cutting force acts parallel to the work surface, is proposed as a novel technique to be used with a high-helix angle end mill. This unique approach enables the reduction of tool wear and improves the surface integrity of machined CFRP surfaces.

The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN + TiN- and AlTiN + TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy

2016 ◽  
Vol 232 (7) ◽  
pp. 1273-1286 ◽  
Author(s):  
Emel Kuram
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tools ◽  
Chip Morphology ◽  
High Speed Milling ◽  
Ti6al4v Titanium Alloy ◽  
Coated Carbide

Tool coatings can improve the machinability performance of difficult-to-cut materials such as titanium alloys. Therefore, in the current work, high-speed milling of Ti6Al4V titanium alloy was carried out to determine the performance of various coated cutting tools. Five types of coated carbide inserts – monolayer TiCN, AlTiN, TiAlN and two layers TiCN + TiN and AlTiN + TiN, which were deposited by physical vapour deposition – were employed in the experiments. Tool wear, cutting force, surface roughness and chip morphology were evaluated and compared for different coated tools. To understand the tool wear modes and mechanisms, detailed scanning electron microscope analysis combined with energy dispersive X-ray of the worn inserts were conducted. Abrasion, adhesion, chipping and mechanical crack on flank face and coating delamination, adhesion and crater wear on rake face were observed during high-speed milling of Ti6Al4V titanium alloy. In terms of tool wear, the lowest value was obtained with TiCN-coated insert. It was also found that at the beginning of the machining pass TiAlN-coated insert and at the end of machining TiCN-coated insert gave the lowest cutting force and surface roughness values. No change in chip morphology was observed with different coated inserts.

Machinability Improvement by Workpiece Preheating during End Milling AISI H13 Hardened Steel

2011 ◽  
Vol 264-265 ◽  
pp. 894-900 ◽  
Author(s):  
Mokhtar Suhaily ◽  
A.K.M. Nurul Amin ◽  
Anayet Ullah Patwari ◽  
Nurhayati Ab. Razak
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tool Life ◽  
Room Temperature ◽  
End Milling ◽  
Hardened Steel ◽  
Cutting Conditions ◽  
Preheating Temperature ◽  
Aisi H13 ◽  
Coated Carbide

Hardened materials like AISI H13 steel are generally regarded as s difficult to cut materials because of their hardness due to intense of carbon content, which however allows them to be used extensively in the hot working tools, dies and moulds. The challenges in machining steels at their hardened state led the way to many research works in amelioration its machinability. In this paper, preheating technique has been used to improve the machinability of H13 hardened steel for different cutting conditions. An experimental study has been performed to assess the effect of workpiece preheating using induction heating system to enhance the machinability of AISI H13. The preheated machining of AISI H13 for two different cutting conditions with TiAlN coated carbide tool is evaluated by examining tool wear, surface roughness and vibration. The advantages of preheated machining are demonstrated by a much extended tool life and stable cut as lower vibration/chatter amplitudes. The effects of preheating temperature were also investigated on the chip morphology during the end milling of AISI H13 tool steel, which resulted in reduction of chip serration frequency. The preheating temperature was maintained below the phase change temperature of AISI H13. The experimental results show that preheated machining led to appreciable increasing tool life compared to room temperature machining. Abrasive wear, attrition wear and diffusion wear are found to be a very prominent mechanism of tool wear. It has been also observed that preheated machining of the material lead to better surface roughness values as compared to room temperature machining.

Influence of cutting tool geometrical parameters on tool wear in high-speed milling of Inconel 718 curved surface

2017 ◽  
Vol 233 (1) ◽  
pp. 18-30 ◽  
Author(s):  
Jian-wei Ma ◽  
Zhen-yuan Jia ◽  
Guang-zhi He ◽  
Zhen Liu ◽  
Xiao-xuan Zhao ◽  
...  
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Tool Life ◽  
Inconel 718 ◽  
High Speed ◽  
Cutting Tool ◽  
Helix Angle ◽  
Curved Surface ◽  
Geometrical Parameters ◽  
High Speed Milling

High-speed machining provides an efficient approach for machining Inconel 718 with high quality and high efficiency. For high-speed milling of Inconel 718 curved surface, the geometrical characteristics are changing continuously leading to a sharp fluctuation of cutting force, which will aggravate the tool wear. As the wear mechanism of coated cutting tool is seriously affected by the cutting tool geometrical parameters, suitable geometrical parameters of cutting tool should be selected to avoid the cutting tool from being worn out very quickly. In this study, the influence of cutting tool geometrical parameters on tool wear in high-speed milling of Inconel 718 curved surface is investigated with coated cutting tool, and the cutting force in milling process is also analyzed. The results show that the cutting force variation can manifest the tool wear degree, and the failure type of coated cutting tool in plane milling and curved surface milling after the same cutting length is different. Furthermore, the cutting tool geometrical parameters seriously affect the tool wear and the tool life in high-speed milling of Inconel 718 curved surface. Concretely, the small rake angle has greater strength and has superiority, the relief angle increasing can enhance the tool life, and the tool life is decreased with the increasing of helix angle for the cutting tool, whose helix angle is larger than 30°. This study provides a theoretical basis for cutting tool wear mechanism and cutting tool geometrical parameter selection in high-speed milling of Inconel 718 curved surface, so as to guarantee the machining efficiency in high-speed milling of Inconel 718 curved surface.

Sign in / Sign up

Export Citation Format

Share Document