Effect of Alloying Elements on the Consolidation and Mechanical Properties of Ti Compacts by SPS

2011 ◽  
Vol 690 ◽  
pp. 469-472 ◽  
Author(s):  
Genki Kikuchi ◽  
Hiroshi Izui
Keyword(s):  
Mechanical Properties ◽  
Tensile Property ◽  
Sintered Density ◽  
Density Ratio ◽  
Alloying Elements ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Stabilizing Element ◽  
Density Rate ◽  
Effect Of Alloying

In this study, we focused on the effect of alloying elements (Fe, Mo, and Al) on the consolidation and mechanical properties of Ti compacts. The elemental blended powders is manufactured by spark plasma sintering. The effects of amount of alloying elements and sintering temperature on the relative density and tensile properties of Ti compacts were investigated. The addition of β-stabilizing elements (Fe and Mo) was found significantly improve the densification of Ti compacts, where the sintered density ratio of Ti-5 wt.% Mo specimen was higher than 99.9 %, and Ti-5 wt.% Fe specimen was higher than 99.0 %. On the other hand, addition of Al as α-stabilizing element showed the sintered density rate of Ti-5 wt.% Al specimen was higher than 99.9 %. The tensile property for sintered Ti-5 wt.% Mo specimens had the highest elongation of 16 %. It will be discussed the microstructures and tensile property of the compacts.

Sintering Performance and Mechanical Properties of Titanium Compacts Prepared by Spark Plasma Sintering

2012 ◽  
Vol 706-709 ◽  
pp. 217-221 ◽  
Author(s):  
Hiroshi Izui ◽  
Genki Kikuchi
Keyword(s):  
Mechanical Properties ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Tensile Property ◽  
Density Ratio ◽  
Alloying Elements ◽  
Blended Elemental ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Stabilizing Element

Titanium alloys were produced by blended elemental powder metallurgy (P/M) method. We focused on the effect of alloying elements (Fe, Mo, and Al) on the consolidation and mechanical properties of Ti compacts prepared by spark plasma sintering. The effects of amount of alloying elements and sintering temperature on the relative density and tensile properties of Ti compacts were investigated. The addition of β-stabilizing elements (Fe and Mo) significantly improved the densification of Ti compacts, where the relative density ratio of Ti-5 wt% Mo specimen became higher than 99.9 %, and Ti-5 wt% Fe specimen higher than 99.0 %. On the other hand, the addition of Al as α-stabilizing element led to improve the relative density of Ti-5 wt% Al compact with higher than 99.9 %. The tensile property for sintered Ti-5 wt% Mo compact had the highest elongation of 16 %. It will be discussed the microstructures and tensile property of the compacts.

scholarly journals Using the spark-plasma technique to produce the mullite-sialon-ZrB2 materials and their properties examination

2018 ◽  
pp. 22-30 ◽  
Author(s):  
A. V. Hmelov
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Elasticity Modulus ◽  
Physical And Mechanical Properties ◽  
Linear Shrinkage ◽  
Plasma Technique ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Crystal Phases ◽  
Density Rate

It was shown how the different sialon and ZrB2ratio in course of the spark-plasma sintering under the pressing load of 75 MPa at 1200‒1600 °C influences the phase composition, the Si3N4and Al2O3content in sialon, the microstructure and crystal phases grain size, the density rate and open porosity, the linear shrinkage and physical and mechanical properties, as well as the linear correlation between the elasticity modulus and ultimate compression strength of the mullite‒sialon‒ZrB2samples.

Fabrication and Mechanical Properties of ultra fine WC-6wt.%Co by Spark Plasma Sintering Process

2011 ◽  
Vol 49 (01) ◽  
pp. 40-45 ◽  
Author(s):  
Hyun-Kuk Park ◽  
Seung-Min Lee ◽  
Hee-Jun Youn ◽  
Ki-Sang Bang ◽  
Ik-Hyun Oh
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Spark Plasma

The Influence of TiC Particles on the Structure and Mechanical Properties of Ni3Al Manufactured By Spark Plasma Sintering

2021 ◽  
Vol 63 (9) ◽  
pp. 1583-1589
Author(s):  
D. A. Osipov ◽  
I. V. Smirnov ◽  
K. V. Grinyaev ◽  
I. A. Ditenberg ◽  
M. A. Korchagin
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Plasma Sintering ◽  
Spark Plasma

scholarly journals The Extrusion and SPS of Zirconium–Copper Powders and Studies of Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3560
Author(s):  
Tomasz Skrzekut ◽  
Grzegorz Boczkal ◽  
Adam Zwoliński ◽  
Piotr Noga ◽  
Lucyna Jaworska ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Intermetallic Compounds ◽  
Room Temperature ◽  
Intermetallic Phase ◽  
Extrusion Process ◽  
Strength Properties ◽  
Plasma Sintering ◽  
Copper Powders ◽  
Spark Plasma ◽  
Zirconium Copper

Zr-2.5Cu and Zr-10Cu powder mixtures were consolidated in the extrusion process and using the spark plasma sintering technique. In these studies, material tests were carried out in the fields of phase composition, microstructure, hardness and tensile strength for Zr-Cu materials at room temperature (RT) and 400 °C. Fractography analysis of materials at room temperature and 400 °C was carried out. The research took into account the anisotropy of the materials obtained in the extrusion process. For the nonequilibrium SPS process, ZrCu2 and Cu10Zr7 intermetallic compounds formed in the material at sintering temperature. Extruded materials were composed mainly of α-Zr and ZrCu2. The presence of intermetallic compounds affected the reduction in the strength properties of the tested materials. The highest strength value of 205 MPa was obtained for the extruded Zr-2.5Cu, for which the samples were cut in the direction of extrusion. For materials with 10 wt.% copper, more participation of the intermetallic phase was formed, which lowered the mechanical properties of the obtained materials. In addition to brittle intermetallic phases, the materials were characterized by residual porosity, which also reduced the strength properties.

Sign in / Sign up

Export Citation Format

Share Document