scholarly journals Applications of Vapor-Liquid-Solid Selective Epitaxy of Highly p-Type Doped 4H-SiC: PiN Diodes with Peripheral Protection and Improvement of Specific Contact Resistance of Ohmic Contacts

2014 ◽  
Vol 778-780 ◽  
pp. 639-644 ◽  
Author(s):  
Nicolas Thierry-Jebali ◽  
Mihai Lazar ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Véronique Soulière ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Vapor Liquid Solid ◽  
Pin Diodes ◽  
High Doping Level ◽  
Selective Epitaxial Growth ◽  
Specific Contact ◽  
P Type ◽  
Vapor Liquid

This work deals with two applications of the Selective Epitaxial Growth of highly p-type doped buried 4H-SiC in Vapor-Liquid-Solid configuration (SEG-VLS). The first application is the improvement of the Specific Contact Resistance (SCR) of contacts made on such p-type material. As a result of the extremely high doping level, SCR values as low as 1.3x10-6Ω.cm2have been demonstrated. Additionally, the high Al concentration of the SEG-VLS 4H-SiC material induces a lowering of the Al acceptor ionization energy down to 40 meV. The second application is the fabrication of PiN diodes with SEG-VLS emitter and guard-rings peripheral protection. Influence of some process parameters and crystal orientation on the forward and reverse characteristics of the PiN diodes is discussed.

Improvement of the Specific Contact Resistance on P-Type 4H-SiC by Using a Highly P-Typed Doped 4H-SiC Layer Selectively Grown by VLS Transport

2014 ◽  
Vol 806 ◽  
pp. 57-60
Author(s):  
Nicolas Thierry-Jebali ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Mihai Lazar ◽  
Gabriel Ferro ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Process Condition ◽  
Specific Contact Resistance ◽  
High Doping Level ◽  
Annealing Temperatures ◽  
Specific Contact ◽  
P Type

This work reports on the improvement of ohmic contacts made on heavily p-type doped 4H-SiC epitaxial layer selectively grown by Vapor-Liquid-Solid (VLS) transport. Even before any annealing process, the contact is ohmic. This behavior can be explained by the high doping level of the VLS layer (Al concentration > 1020 cm-3) as characterized by SIMS profiling. Upon variation of annealing temperatures, a minimum value of the Specific Contact Resistance (SCR) down to 1.3x10-6 Ω.cm2 has been obtained for both 500 °C and 800 °C annealing temperature. However, a large variation of the SCR was observed for a same process condition. This variation is mainly attributed to a variation of the Schottky Barrier Height.

Ohmic Contacts to p-Type InGaAs/InP with a Graded Bandgap Heterobarrier

1993 ◽  
Vol 318 ◽  
Author(s):  
Patrick W. Leech ◽  
Geoffrey K. Reeves
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Rutherford Backscattering Spectrometry ◽  
Specific Contact Resistance ◽  
Superlattice Structure ◽  
Specific Contact ◽  
P Type ◽  
Metal Layers ◽  
Anneal Temperature ◽  
Graded Bandgap

ABSTRACTOhmic contacts to p-type InP with an In0.47Ga0.53As buffer layer and an interposed superlattice of 50 Å In0.47Ga0.53As/ 50 Å InP have been investigated. Initial studies of contacts to In0.47Ga0.53As/ InP without the superlattice structure have shown that Pd/Zn/Pd/Au metallization produced a lower specific contact resistance (pc = 1.1 × 10−4 Ω cm2) than Pd/Ge/Au, and over a wider range of anneal temperature than Au/Zn/Au. The incorporation of the superlattice in the p-In0.47Ga0.53As/ InP structure resulted in Pd/Zn/Pd/Au contacts with pc of 3.2 × 10−5 Ω cm2 as-deposited and 7.5 × 10−6 Ω.cm2 after a 500 °C anneal. The presence of Pd/Zn in the metallization was shown as important in reducing pc. Significant intermixing of the metal layers and In0.47Ga0.53As occured at ≥ 350 °C, as revealed by Rutherford backscattering spectrometry.

Ni-Al-Ti Ohmic Contacts with Preserved Form Factor and Few 10- 4 Ωcm2 Specific Resistance on 0.1-1 Ωcm p-Type 4H-SiC

2018 ◽  
Vol 924 ◽  
pp. 385-388 ◽  
Author(s):  
Roberta Nipoti ◽  
Maurizio Puzzanghera ◽  
Maria Concetta Canino ◽  
Giovanna Sozzi ◽  
Paolo Fedeli
Keyword(s):  
Form Factor ◽  
Contact Resistance ◽  
Contact Area ◽  
Room Temperature ◽  
Ohmic Contacts ◽  
Specific Resistance ◽  
Thickness Ratio ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type

This study shows that a thin Ni film on Al/Ti/4H-SiC metal pads allows to preserve the pad form factor during a 1000 °C/2 min treatment, provided that the Al and Ti film thicknesses are sufficiently thin. Moreover, by reducing the Al to Ti thickness ratio, droplet formation in the contact area is avoided and a mirror-like appearance is obtained. This optimal contact morphology corresponds to a specific contact resistance of few 10-4Ωcm2at room temperature on p-type 4H-SiC with resistivity in the range 0.1 – 1 Ωcm.

Al/Ni And Al/Ti Ohmic Contact To P-type SiC Diffused Layer

2000 ◽  
Vol 640 ◽  
Author(s):  
Xaiobin Wang ◽  
Stanislav Soloviev ◽  
Ying Gao ◽  
G. Straty ◽  
Tangali Sudarshan ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Metal Contacts ◽  
Transfer Length ◽  
Type Layer ◽  
Transmission Line Method ◽  
Specific Contact ◽  
Background Doping ◽  
P Type

ABSTRACTOhmic contacts to p-type SiC were fabricated by depositing Al/Ni and Al/Ti followed by high temperature annealing. A p-type layer was fabricated by Al or B diffusion from vapor phase into both p-type and n-type substrates. The thickness of the diffused layer was about 0.1–0.2 μm with surface carrier concentration of about 1.0×1019cm−3. Metal contacts to a p-type substrate with a background doping concentration of 1.2×1018cm−3, without a diffusion layer, were also formed. The values of specific contact resistance obtained by Circular Transmission Line Method (CTLM) and Transfer Length Method (TLM) for the n-type substrate, and by Cox & Strack method for p-type substrate, respectively, varied from 1.3×10−4Ωcm2 to 8.8×10−3 Ωcm2. The results indicate that the specific contact resistance could be significantly reduced by creating a highly doped diffused surface layer.

scholarly journals Comparison of Electrical Properties of Ohmic Contact Realized on p-Type 4H-SiC

2008 ◽  
Vol 600-603 ◽  
pp. 639-642
Author(s):  
Duy Minh Nguyen ◽  
Christophe Raynaud ◽  
Mihai Lazar ◽  
Heu Vang ◽  
Dominique Planson
Keyword(s):  
Surface Roughness ◽  
Electrical Properties ◽  
Contact Resistance ◽  
Carrier Mobility ◽  
Ohmic Contacts ◽  
Series Resistance ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type ◽  
Post Implantation

N+ 4H-SiC commercial substrates with n-type epilayers have been used to realize bipolar diodes and TLM structures. The p-type emitter of diodes was realized by Al implantations followed by a post-implantation annealing with or without a graphite capping layer. Ohmic contacts were formed by depositing Ti/Ni on the backside and Ni/Al on the topside of the wafer. It appears that capping the sample during the annealing reduces considerably the surface roughness and the specific contact resistance. Sheet resistance and specific contact resistance as low as 2kΩ/□ and respectively 1.75×10-4 Ωcm² at 300 K have been obtained. I-V measurements as a function of temperature have been performed from ~100 to ~500 K. The variations of the series resistance vs. temperature can be explained by the freeze-out of carriers and by the variation of carrier mobility.

Low-Resistance Electrical Contacts to p-Type GaN by Using InxGa1-xN Cap Layers

2001 ◽  
Vol 693 ◽  
Author(s):  
Th. Gessmann ◽  
Y.-L. Li ◽  
J. W. Graff ◽  
E. F. Schubert ◽  
J. K. Sheu
Keyword(s):  
Contact Resistance ◽  
Electric Fields ◽  
Ohmic Contacts ◽  
Electrical Contacts ◽  
Specific Contact Resistance ◽  
Low Resistance ◽  
Transmission Line Method ◽  
Specific Contact ◽  
P Type ◽  
20 Nm

AbstractA novel type of low-resistance ohmic contacts is demonstrated utilizing polarization-induced electric fields in thin p-type InGaN layers on p-type GaN. An increase of the hole tunneling probability through the barrier and a concomitant significant decrease of the specific contact resistance can be attributed to a reduction of the tunneling barrier width in the InGaN capping layers due to the polarization-induced electric fields. The specific contact resistance of Ni (10 nm) / Au (30 nm) contacts deposited on the InGaN capping layers was determined by the transmission line method. Specific contact resistances of 1.2 × 10-2 Ω cm2 and 6 × 10-3 & cm2 were obtained for capping layer thicknesses of 20 nm and 2 nm, respectively.

Formation of Ni/Pt/Au Ohmic Contacts to p-GaN

1997 ◽  
Vol 482 ◽  
Author(s):  
Ja-Soon Jang ◽  
Hyo-Gun Kim ◽  
Kyung-Hyun Park ◽  
Chang-Sub Um ◽  
Il-Ki Han ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contact ◽  
Ohmic Contacts ◽  
Chemical Vapor ◽  
Electron Beam Evaporation ◽  
Specific Contact Resistance ◽  
Metal Thin Films ◽  
Linear Behavior ◽  
Specific Contact ◽  
P Type

AbstractWe report a new Ni/Pt/Au (20/30/80 nm) metallization scheme to achieve a low ohmic contacts to p-type GaN with a carrier concentration of 9.4 × 1016 cm-3. A Mg-doped GaN layer (0.5 μm) was grown on (0001) sapphire substrate by metalorganic chemical vapor deposition (MOCVD). All metal thin films were deposited on the p-GaN layer in an electron-beam evaporation system. Samples were annealed by a rapid thermal annealing (RTA) process at a range of temperatures from 300 °C to 850 °C under a flowing Ar atmosphere. A circulartransmission line model (c-TLM) was employed to calculate the specific contact resistance, and current-voltage (I-V) data were measured with HP4155A. The Ni/Pt/Au contacts without the annealing process showed nearly rectifying characteristics. The ohmic contacts were formed on the samples annealed at 500 °C for 30 sec and the I-V data showed a linear behavior. The specific contact resistance was 2.1 × 10-2 Ωcm2. However with increasing the annealing temperature above 600 °C, ohmic contacts were again degraded. Auger electron spectroscopy (AES) depth profiles were used to investigate the interfacial reactions between the trilayer and GaN. AES results suggested that Pt plays a significant role in forming ohmic contact as an acceptor at the interface. Atomic force microscope (AFM) also showed that the samples with good ohmic contact have very smooth surface.

Optimization of Pd/Zn/Pd/Au Ohmic Contacts to p-Type inGaAs/ InP

1994 ◽  
Vol 337 ◽  
Author(s):  
Patrick W Leech ◽  
Geoffrey K. Reeves
Keyword(s):  
Thermal Stability ◽  
Electrical Properties ◽  
Contact Resistance ◽  
Ohmic Contacts ◽  
Critical Thickness ◽  
Specific Contact Resistance ◽  
Zn Doping ◽  
Specific Contact ◽  
P Type ◽  
Thermal Stability Of

ABSTRACTThe electrical properties of Pd/Zn/Pd/Au based ohmic contacts to p-type In0 47Ga0 53As/ InP with an interposed superlattice of 50Å In047Gao 53As/ 50 Å InP have been investigated. In this study, several configurations of the Pd/Zn/Pd/Au metallization were fabricated with varying thicknesses of the Zn and interfacial Pd layers in the range 0 to 400 Å. The lowest values of specific contact resistance, ρc, were 1.2 x 10-5 Ω cm2 as-deposited and 7.5 x 106 Ω cm2 for samples annealed at 500 °C. In the as-deposited structures, ρc was reduced by an increase in thickness of both the Zn and Pd layers to 300 Å. For annealed samples, a critical thickness of the Zn ≥ 50 Å and Pd ≥ 100 Å layers was required in order to significantly reduce the magnitude of ρc. These results are consistent with a model of Pd/Zn contacts based on Zn doping of the interface. Studies of thermal stability of the contacts at 400 °C and 500 °C have shown that the Zn/Pd/Au and Pd/Zn/Pd/Au configurations were significanty lower in ρc at extended ageing times than the Pd/Au contacts.

Ohmic Contacts to P-Type Epitexial and Imlanted 4H-SiC

2006 ◽  
Vol 527-529 ◽  
pp. 895-898 ◽  
Author(s):  
John Crofton ◽  
John R. Williams ◽  
A.V. Adedeji ◽  
James D. Scofield ◽  
S. Dhar ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Contact Resistance ◽  
Barrier Height ◽  
Ohmic Contacts ◽  
Doping Concentration ◽  
Theoretical Calculations ◽  
Specific Contact Resistance ◽  
Acceptor Doping ◽  
Specific Contact ◽  
P Type

Nickel ohmic contacts to p-type epitaxial and heavily implanted 4H-SiC are described. Room and elevated temperature results are presented. Elevated temperature measurements of specific contact resistance are compared to theoretical calculations. The calculations require the acceptor doping concentration and the contact’s barrier height. Epitaxial material has a known acceptor value thereby allowing the barrier height to be deduced by requiring agreement between the calculated and measured values of the contact resistance. Calculations of the contact resistance for implanted material use the barrier height from the epitaxial results along with a variable activated acceptor doping concentration which is adjusted to give agreement with measured room temperature specific contact resistances. Specific contact resistances as low as 7x10-6 ohm-cm2 fabricated on the Si face have been obtained to epitaxial 4H p-type material whereas contacts to implanted material result in much larger contact resistance values of 4x10-5 ohm-cm2. These results, when compared to theoretical calculations, indicate that activated acceptor doping concentrations in heavily implanted material are on the order of 2% of the implant concentration.

Sign in / Sign up

Export Citation Format

Share Document