scholarly journals The Effects of Rolling Deformation and Annealing Treatment on Damping Capacity of 1200 Aluminium Alloy

2015 ◽  
Vol 819 ◽  
pp. 20-24
Author(s):  
Mohd Noor Mazlee ◽  
Shamsul Baharin Jamaludin ◽  
Y. Yasmin ◽  
Shaiful Rizam Shamsudin ◽  
M.S. Risby ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Aluminium Alloy ◽  
Microstructural Evolution ◽  
Rolling Direction ◽  
Annealing Treatment ◽  
Rolling Reduction ◽  
Damping Capacity ◽  
Percent Reduction ◽  
Rolling Deformation

Annealing treatment is an important step of rolling deformation that contributes to microstructural evolution and leads to the significant changes in damping capacity. Damping capacities were analyzed in the parallel to rolling direction at 1 and 10 Hz respectively. It was found that severe plastic deformation at 40 percent reduction has lower damping capacity compared to that of 30 percent and 20 percent reductions respectively. The microstructural results show that the grains of as rolled alloys were changed to almost equiaxed structures after a rolling reduction at 40 percent reduction.

scholarly journals The Effects of Cold Rolling Process and Annealing Treatment on Damping Properties of 3105 Aluminium Alloy

2017 ◽  
Author(s):  
MUHAMMAD SYAFIQ BIN ZAKARIA
Keyword(s):  
Cold Rolling ◽  
Aluminium Alloy ◽  
Strain Hardening ◽  
Loss Modulus ◽  
Annealing Treatment ◽  
Hardness Measurement ◽  
Rolling Process ◽  
Rolling Reduction ◽  
Damping Capacity ◽  
Damping Properties

The aluminium alloy have deformed by cold rolling process to 50 percent, 60 percent, and 70 percent rolling reduction. In order to reduce the strain hardening of the samples, an annealing treatment was performed after cold worked process. The lower the rolling reduction, the higher the damping capacity of the samples. The sample for 50 percent rolling reduction before annealed has increase in damping capacity from 0.0361 to 0.1318. When the samples undergo two different annealing temperatures and soaking hours, the damping properties such as loss modulus, storage modulus, and damping capacity show some changes in trend curves and experimental value. The damping capacity for sample 50 percent rolling reduction and after annealed at temperature 300 °C for one hour was increased from 0.0193 to 0.1405 at temperature 50 °C to 380 °C. The hardness measurement showed that, the value of Vickers hardness were decrease after annealed due to the decreasing in strain hardening.

Superplasticity of Aerospace 7075 (Al-Zn-Mg-Cu) Aluminium Alloy Obtained by Severe Plastic Deformation

2018 ◽  
Vol 385 ◽  
pp. 39-44 ◽  
Author(s):  
Fernando Carreño ◽  
Oscar A. Ruano
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Aluminium Alloy ◽  
Room Temperature ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
Aerospace Applications ◽  
Boundary Sliding ◽  
Processing Stress

The 7075 (Al-Zn-Mg-Cu) aluminium alloy is the reference alloy for aerospace applications due to its specific mechanical properties at room temperature, showing excellent tensile strength and sufficient ductility. Formability at high temperature can be improved by obtaining superplasticity as a result of fine, equiaxed and highly misoriented grains prone to deform by grain boundary sliding (GBS). Different severe plastic deformation (SPD) processing routes such as ECAP, ARB, HPT and FSP have been considered and their effect on mechanical properties, especially at intermediate to high temperatures, are studied. Refined grains as fine as 100 nm and average misorientations as high as 39o allow attainment of high strain rate superplasticity (HSRSP) at lower than usual temperatures (250-300oC). It is shown that increasing misorientations are obtained with increasing applied strain, and increasing grain refinement is obtained with increasing processing stress. Thus, increasing superplastic strains at higher strain rates, lower stresses and lower temperatures are obtained with increasing processing strain and, specially, processing stress.

Superplasticity in a 5024 Aluminium Alloy Processed by Severe Plastic Deformation

2012 ◽  
Vol 735 ◽  
pp. 353-358 ◽  
Author(s):  
Anna Mogucheva ◽  
Diana Tagirova ◽  
Rustam Kaibyshev
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Strain Rate ◽  
Aluminium Alloy ◽  
Initial Strain Rate ◽  
Strain Rates ◽  
Superplastic Behaviour ◽  
Angular Pressing ◽  
Elongation To Failure ◽  
Zr Alloy

The superplastic behaviour of an Al-4.6%Mg-0.35%Mn-0.2%Sc-0.09%Zr alloy was studied in the temperature range 250-500°C at strain rates ranging from 10-4 to 10-1 s-1. The AA5024 was subjected to equal channel angular pressing (ECAP) at 300°C up to ~12. The highest elongation-to-failure of ∼3300% was attained at a temperature of 450°C and an initial strain rate of 5.6×10-1 s-1. Regularities of superplastic behaviour of the 5024 aluminium alloy are discussed.

scholarly journals Influence of Plastic Deformation on Microstructural Evolution of 100Cr6 Bearing Ring in Hot Ring Rolling

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4355
Author(s):  
Guanghua Zhou ◽  
Wenting Wei ◽  
Qinglong Liu
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Microstructural Evolution ◽  
Vickers Hardness ◽  
Microstructural Characterization ◽  
Lamellar Spacing ◽  
Rolling Process ◽  
Rolling Reduction ◽  
Ring Rolling ◽  
Bearing Rings

The hot ring rolling technology as the crucial procedure for the manufacture of bearing rings plays an important role in determining the final microstructure of bearing rings. In this work, the influence of the hot ring rolling process on the microstructural evolution of 100Cr6 bearing rings was investigated using a three-dimensional (3D) numerical model and microstructural characterization. It was found that the significant microstructural refinement occurs at the different regions of the rings. However, owing to the non-uniform plastic deformation of hot rolling, the refinement rate of grain size and decrease of pearlite lamellar spacing (PLS) also showed uniformity at different regions of the rings. Furthermore, the degree of grain refinement had been limited with the increase of rolling reduction. Due to the refined grain size and decreased PLS, the Vickers hardness increased with the increase of rolling reduction. Moreover, the Vickers hardness from the outer surface to the inner surface of the ring is asymmetrical u-shaped, which had the law of lower hardness in the center area and higher hardness on the surface.

Microstructural evolution in copper processed by severe plastic deformation

2005 ◽  
Vol 410-411 ◽  
pp. 290-298 ◽  
Author(s):  
A. Mishra ◽  
V. Richard ◽  
F. Grégori ◽  
R.J. Asaro ◽  
M.A. Meyers
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Microstructural Evolution
Sign in / Sign up

Export Citation Format

Share Document