Effect of Filler Metals on the Microstructures and Mechanical Properties of Dissimilar Low Carbon Steel and 316L Stainless Steel Welded Joints

2015 ◽  
Vol 819 ◽  
pp. 57-62 ◽  
Author(s):  
M.F. Mamat ◽  
E. Hamzah ◽  
Z. Ibrahim ◽  
A.M. Rohah ◽  
A. Bahador
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Base Metal ◽  
Arc Welding ◽  
316L Stainless Steel ◽  
Filler Metal ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Steel Base ◽  
Welding Electrode

In this paper, dissimilar joining of 316L stainless steel to low carbon steel was carried out using gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW). Samples were welded using AWS: ER309L welding electrode for GMAW and AWS: ER316L welding electrode for GTAW process. Determination of mechanical properties and material characterization on the welded joints were carried out using the Instron tensile test machine and an optical microscope respectively. The cross section area of the welded joint consists of three main areas namely the base metal (BM), heat affected zone (HAZ), and weld metal (WM). It was found that, the yield and tensile strengths of welded samples using ER316L filler metal were slightly higher than the welded sample using ER309L welding electrode. All welded samples fractured at low carbon steel base metal indicating that the regions of ER316L stainless steel base metal, ER316L filler metal and heat affected zone (HAZ) have a higher strength than low carbon steel base metal. It was also found that ER316L welding electrode was the best filler to be used for welding two dissimilar metals between carbon and stainless steel.

Characterization of Duplex Stainless Steel/Cold Reduced Low Carbon Steel Dissimilar Weld Joints by GTAW

2015 ◽  
Vol 766-767 ◽  
pp. 780-788
Author(s):  
D. Devakumar ◽  
D.B. Jabaraj ◽  
V.K. Bupesh Raja ◽  
P. Periyasamy
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Carbon Steel ◽  
Duplex Stainless Steel ◽  
Base Metal ◽  
Arc Welding ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Weld Joints ◽  
Gas Tungsten Arc

The purpose of this study is to evaluate the mechanical and metallurgical properties of dissimilar metal weld joints between duplex stainless steel/Cold Reduced low carbon Steel (CRS) by Gas Tungsten Arc Welding (GTAW) process. The dissimilar 2 mm thickness plates of duplex stainless steel and cold reduced low carbon steel, conforming to AISI 2205 and IS 513_2008 CR2_D were butt welded by means of gas tungsten arc welding using argon as shielding gas. The butt welding joint arrangement was used for this experiment using E 309L electrode as filler metal. The joints were investigated for mechanical properties and microstructure. Tensile, Hardness and bend tests were carried out to evaluate the mechanical properties. Optical microscopy was used to explore the microstructure. The micro structural examination of the weld region revealed dendritic delta ferrite. Micro examination of DSS base metal revealed elongated grains of austenite (white) with ferrite (Brown). Micro examination of CRS base metal discloses deformed grains of ferrite present in the matrix. Fracture analysis was conducted for the failure part with Scanning Electron Microscope (SEM) and found ductile fracture occurred at CR steel side.

Estimation of Some Mechanical Properties for Similar & Dissimilar Welded Joints

2014 ◽  
Vol 2 (1) ◽  
pp. 59-76
Author(s):  
Abdullah Daie'e Assi
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Austenitic Stainless Steel ◽  
Base Metal ◽  
Welded Joints ◽  
Plate Thickness ◽  
Low Carbon Steel ◽  
Dissimilar Metals ◽  
Low Carbon ◽  
Steel Type

This research deals with the choice of the suitable filler metal to weld the similar and dissimilar metals (Low carbon steel type A516 & Austenitic stainless steel type 316L) under constant conditions such as, plate thickness (6 mm), voltage (78 v), current (120 A), straight polarity. This research deals with three major parts. The first parts Four types of electrodes were used for welding of dissimilar metals (C.St A516 And St.St 316L) two from mild steel (E7018, E6013) and other two from austenitic stainless steel (E309L, E308L) various inspection were carried out include (Visual T., X-ray T., δ- Ferrite phase T., and Microstructures T.) and mechanical testing include (tensile T., bending T. and micro hardness T.) The second parts done by used the same parameters to welding similar metals from (C.St A516) Or (St.St 316L). The third parts deals with welding of dissimilar weldments (C.St And St.St) by two processes, gas tungsten are welding (GTAW) and shielded metal are welding (SMAW).        The results indicated that the spread of carbon from low carbon steel to the welding zone in the case of welding stainless steel elect pole (E309L) led to Configuration Carbides and then high hardness the link to high values ​​compared with the base metal. In most similar weldments showed hardness of the welding area is  higher than the hardness of the base metal. The electrode (E309L) is the most suitable to welding dissimilar metals from (C.St A516 With St.St 316L). The results also showed that the method of welding (GTAW) were better than the method of welding (SMAW) in dissimilar welded joints (St.St 316L with C.St A516) in terms of irregular shape and integrity of the welding defects, as well as characterized this weldments the high-lift and resistance ductility good when using the welding conditions are similar.

scholarly journals Comparative Study on the Activity of GaF3 and Ga2O3 Nanoparticle-Doped CsF-AlF3 Flux for Brazing 6061 Al/Q235 Steel Joints

Crystals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 498 ◽  
Author(s):  
Zhen Yao ◽  
Songbai Xue ◽  
Junxiong Zhang
Keyword(s):  
Aluminum Alloy ◽  
Comparative Analysis ◽  
Carbon Steel ◽  
Base Metal ◽  
Filler Metal ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
6061 Aluminum Alloy ◽  
Steel Joints ◽  
Molten Filler Metal

The effect of trace amounts of GaF3 and Ga2O3 nanoparticles on the wettability and spreadability of CsF-AlF3 flux matched Zn-15Al filler metal were comparatively studied on 6061 aluminum alloy and Q235 low-carbon steel. The experimental results indicate that appropriate amounts of GaF3 and Ga2O3 added into the flux could significantly promote the Zn-15Al filler metal to wet and spread on the surface of 6061 aluminum alloy and Q235 low-carbon steel. The optimum ranges for GaF3 and Ga2O3 were 0.0075–0.01wt.% and 0.009–0.01 wt.%, respectively. Comparative analysis showed that the activity of CsF-AlF3 flux bearing GaF3 was higher than that bearing Ga2O3. The reason for this is that the former flux has a stronger ability to remove oxides of the base metal and reduce the interfacial tension of the molten filler metal and the base metal.

Effect of Filler Alloy on Microstructure, Mechanical and Corrosion Behaviour of Dissimilar Weldment between Aisi 201 Stainless Steel and Low Carbon Steel Sheets Produced by a Gas Tungsten Arc Welding

2012 ◽  
Vol 581-582 ◽  
pp. 808-816 ◽  
Author(s):  
Chuaiphan Wichan ◽  
Srijaroenpramong Loeshpahn
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Weld Metal ◽  
Base Metal ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Delta Ferrite ◽  
Steel Sheets ◽  
Gas Tungsten Arc ◽  
Weld Metals

The joining of austenitic stainless steel (AISI 201) to low carbon steel sheets (CS) was attempted by gas tungsten arc welding (GTAW) with four types of consumables. The studied consumables were ER308L, ER309L, ER316L stainless steel wires, and AWS A5.18 carbon steel wire. The welding parameters – i.e. the current of 90 A and the welding speed of 62 mm.min-1 – were fixed in all welding operations. The microstructure of weld metal produced by stainless steel consumables consisted of delta ferrite in austenite matrix. The delta ferrite in the form of continuous dendrite was observed in weld metals produced by 308L and 309L fillers. The dendrite of delta ferrite was relatively discontinuous in weld metal produced by 316L filler. The microstructure of weld metal produced by carbon steel filler consisted of equiaxed ferrite and pearlite, similar to that of carbon steel. The corrosion behavior of weld metal was investigated by potentiodynamic method. Specimens were tested in 0.35-wt% NaCl solution saturated by laboratory air at 27°C. It was found that the corrosion potential of weld metal produced by carbon steel filler was considerably lower than those of AISI 201 base metal and weld metals welded using stainless steel consumables. Weld metals produced by stainless steel fillers –308L,309L and316L– exhibited the similar corrosion potentials as that of 201 base metal. The pitting potentials of weld metals produced by 309L, 316L fillers were higher than those of 201 base metal and weld metal produced by 308L filler respectively. It was discussed that the increase of Cr content in weld metals by using 309L filler contained with 24.791 wt% of Cr, or the addition of Cr and Mo in weld metals by using 316L filler contained with 21.347 wt% of Cr and 2 wt% of Mo, promoted the pitting corrosion resistance of weld metal to be comparable with that of Fe-17Cr-3Ni (201) base metal. An emission spectroscopy was applied to quantify the amount of elements in weld metals. By considering the contents of Cr and Mo, the pitting resistance equivalent number (PREN) of each weld metal was calculated. The discussion of the corrosion resistance of weld metals related to PREN and microstructure was made in the paper.

Study on Process and Defect of Arc Welding

2014 ◽  
Vol 608-609 ◽  
pp. 770-774
Author(s):  
Li Min Zhang
Keyword(s):  
Numerical Simulation ◽  
Stainless Steel ◽  
Carbon Steel ◽  
Arc Welding ◽  
Low Carbon Steel ◽  
Theory Model ◽  
Low Carbon ◽  
Flat Punch ◽  
Forming Mechanism ◽  
Material Forming

This paper welds a layer of austenitic stainless steel (SS316L) on specimen of low carbon steel (C15) with a cylindrical surface using MIG Technology in the experiment. The sample was upsetting experiment, cracks and material forming observation respectively using embossing punch, no lubrication flat punch and lubrication flat punch under the condition of 750 °C, 900 °C and 1050 °C. The paper research on forming mechanism of the specimen under laboratory conditions based on the experimental results, the axial symmetry theory model and Numerical Simulation.

scholarly journals Weld Overlay Technique using Different Filler Rod Size to Overcome Internal Corrosion of Low Carbon Steel Base Metal

2020 ◽  
Vol 9 (3) ◽  
pp. 654-660
Keyword(s):  
Carbon Steel ◽  
Base Metal ◽  
Low Carbon Steel ◽  
Chloride Ions ◽  
Low Carbon ◽  
Internal Corrosion ◽  
Weld Overlay ◽  
Electrode Size ◽  
Steel Base ◽  
Overlay Welding

Overlay welding is commonly used to repair and replace the affected corroded surface of the base metal of a component. In other words, it is used to restore the original dimensions of the component. Weld overlay usually applies a corrosion resistant or hard facing layer onto the base metal. This experiment is to determine the suitable filler rod size in repairing corroded low carbon steel (LCS) base metal, respectively to the affected area and to identify the type of distortion occurring on the weldment. It is also to examine the microstructure of the joint between the overlay weld and corroded low carbon steel base metal using SEM/EDX. The overlay welding process was conducted on the corroded samples using SMAW process at defined attacked corroded areas. Filler electrode E-7018 with two diameter sizes of 3.2mm and 2.6mm were selected. It was found that the bigger electrode size produced higher degree of distortion angle compared to smaller electrode size. Resulting from the metallographic and SEM/EDX analysis, the joint between weld overlay and corroded LCS were fused well without any sign of oxides or other impurities present. Overlay welding also remove the sign of chloride ions that cause the LCS base metal to corrode. Thus, the repairing technique using overlay welding was found successful in repairing corroded LCS base metal. Therefore, the most suitable electrode size to do overlay welding on corroded low carbon steel base metal is 2.6 mm diameter electrode

Numerical Analysis of Residual Stresses in V-Butt Welded Joint of Two Dissimilar Pipes

2013 ◽  
Author(s):  
Gurinder Singh Brar ◽  
Gurdeep Singh
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Carbon Steel ◽  
Residual Stresses ◽  
Filler Metal ◽  
Welded Joint ◽  
Low Carbon Steel ◽  
Stress Distributions ◽  
Low Carbon

In this paper a three-dimensional welding simulation was carried out by commercially available finite element software to predict temperature and the residual stress distributions in V-butt welded joint of two dissimilar pipes. Low carbon steel and stainless steel pipe welding is widely used in a variety of engineering applications such as oil and gas industries, nuclear and thermal power plants and chemical plants. Inelastic deformations during heat treatment are the major cause of residual stress. Heat during welding causes localized expansion as some areas cool and contract more than others. The stress variation in the weldment can be very complex and can vary between compressive and tensile stresses. The mismatching (in the weld in general) occurs due to joint geometry and plate thickness. Welding procedures and degree of restraints also influences the residual stress distributions. To understand the behavior of residual stress, two dissimilar pipes one of stainless steel and another of low carbon steel with outer diameter of 356 mm and internal diameter 240 mm were butt welded. The welding was completed in three passes. The first pass was performed by Manual TIG Welding using ER 309L as a filler metal. The remaining weld passes were welded by Manual Metal Arc Welding (MMAW) and ER 309L-16 was used as a filler metal. During each pass, attained peak temperature and variation of residual stresses and magnitude of axial stress and hoop stress in pipes has been calculated. The results obtained by finite element method agree well with those from Ultrasonic technique (UT) and Hole Drilling Strain-Gauge (HDSG) as published by Akhshik and Moharrami (2009) for the improvement in accuracy of the measurements of residual stresses.

Sign in / Sign up

Export Citation Format

Share Document