Gold Cementation by Dendritic Zinc Powders in Percolation Mode

2020 ◽  
Vol 989 ◽  
pp. 543-547
Author(s):  
K.D. Naumov ◽  
Vladimir G. Lobanov
Keyword(s):  
Particle Size ◽  
Physical Properties ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
Alkaline Solutions ◽  
Wide Range ◽  
Zinc Powders ◽  
Cyanide Solutions

In present article gold cementation features from cyanide solutions using dendritic zinc powders are studied. The powders were obtained by electroextraction from alkaline solutions. Powders with different physical properties were obtained by means of change in current density (from 0.5 to 2 A/m2) and NaOH concentration in solution (from 100 to 400 g/dm3) at the constant zinc concentration (10 g/dm3). The physical properties of mentioned powders were studied using SEM (Jeol JSM-6390LA), BET (Gemini VII 2390) and laser diffraction (Sympatec HELOS & RODOS). It is shown that electrolytic powders have high specific surface area, which is 1.8–2.6 times larger than the surface area of ​​the zinc powder currently used for cementation. At that electrolytic powders particle size is 8-22 times larger than the particle size of powder currently used for cementation. The reason of high specific surface area is the electrolytic zinc powders dendritic structure. It was found that the obtained powders precipitate gold from cyanide solutions with a greater efficiency in a wide range of productivity. Laboratory unit simulating Merrill-Crow technology was used for cementation. Immediately ahead conducting the experiments, Na2SO3 was added to the solution in excess to remove dissolved oxygen. Zinc powders were plated by dendritic lead before loading into the laboratory setup by cementation. Lead was added as acetate (Pb (CH3COO)2). The consumption of lead acetate was 10% by weight of zinc. Correlation between the powders physical properties and the gold extraction is shown.

scholarly journals Features of gold cementation in percolation mode by electrolytic zinc powders

2020 ◽  
pp. 19-26
Author(s):  
K. D. Naumov ◽  
V. G. Lobanov
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Fine Powder ◽  
Zinc Powder ◽  
Gold Deposition ◽  
Electrolytic Zinc ◽  
Zinc Powders ◽  
Cyanide Solutions

The study covers physicochemical features of dendritic zinc powders and their effect on gold cementation from cyanide solutions. Three zinc powders were obtained in a laboratory environment by electroextraction at different conditions, and these powders featured various particle size and specific surface area. The properties of zinc powders obtained and powder currently used for gold cementation were evaluated using SEM (Jeol JSM-6390LA), BET (Gemini VII 2390) and laser diffraction (Sympatec HELOS & RODOS) methods. It is shown that electrolytic powders have high specific surface area (1.3–2.6 times more) and a low bulk density (3.1–3.8 times less), relative to zinc powder currently used for gold cementation. It was found that due to specific physical properties electrolytic powders have low hydraulic resistance, which eliminates the need for inert additives introduced during cementation, increases unit capacity and reduces the load on equipment. Inert additives elimination will additionally increase the gold content in the resulting product. The dendritic morfology of zinc powders obtained compensates high particle size resulting in the high efficiency of gold precipitation. At the long cementation cycle the effective gold deposition area (with gold extraction of more than 97 %) turned out to be shorter for electrolytic powder compared to fine powder currently used. However, in practice, the cementation cycle is always limited by fine powder throughput and it is not possible to achieve the full zinc potential. The resulting cementation product usually contains 25–35 % of unused zinc. These studies show the effectiveness of using electrolytic zinc powder for gold cementation from cyanide solutions.

Physical Properties Variability of Zinc Powders Obtained by Electrochemical Method

2021 ◽  
Vol 316 ◽  
pp. 689-693
Author(s):  
K.D. Naumov ◽  
V.G. Lobanov
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Bulk Density ◽  
Surface Area ◽  
Specific Surface Area ◽  
Current Density ◽  
Zinc Concentration ◽  
Regulatory Change ◽  
Average Particle ◽  
Zinc Powders

The aim of this paper is to establish a regulatory change of zinc powders key physicochemical properties with varying electroextraction conditions. It was studied influence zinc concentration, alkali concentration and current density. Quantitative dependencies of zinc powders particle size and specific surface area from mentioned electroextraction parameters are shown. At increasing of zinc concentration, decreasing of NaOH concentration and decreasing of current density of powders particle size growth, correspondingly specific surface area is declined. It is indicated, that electrolytic zinc powders bulk density varies from 0.61 g/cm3 to 0.75 g/cm3 with a decrease of average particle size from 121 μm to 68 μm. In comparison, spherical powders bulk density used in various industries is currently 2.45-2.6 g/cm3. In all experiments, metal zinc content varied in the range of 91.1-92.5%, the rest - ZnO. To a greater extent, this indicator depends on powder washing quality from alkali and storage conditions.

scholarly journals Preparation and characterization of high specific surface area Mn3O4 from electrolytic manganese residue

2010 ◽  
Vol 8 (5) ◽  
pp. 1059-1068 ◽  
Author(s):  
Tiefeng Peng ◽  
Longjun Xu ◽  
Hongchong Chen
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Magnetic Measurements ◽  
High Specific Surface Area ◽  
Surface Areas ◽  
Electrolytic Manganese ◽  
Electrolytic Manganese Residue ◽  
Specific Surface Areas

AbstractMn3O4 powders have been produced from Electrolytic Manganese Residue (EMR). After leaching of EMR in sulfuric acid, MnSO4 solution containing various ions was obtained. Purifying the solution obtained and then adding aqueous alkali to the purified MnSO4 solution, Mn(OH)2 was prepared. Two methods were employed to produce Mn3O4. One way was oxidation of Mn(OH)2 in aqueous phase under atmosphere pressure to obtain Mn3O4. The other way was roasting Mn(OH)2 precursors in the range of 500°C to 700°C. The prepared samples were investigated by using several techniques including X-ray powder diffraction (XRD), Fourier Transformation Infra-Red (FTIR) spectra, and Brunauer-Emmett-Teller (BET) specific surface area instrument. Particle distribution and magnetic measurements were carried out on laser particle size analyzer, vibrating sample magnetometer (VSM). Through XRD, FTIR and determination of total Mn content (TMC), the products prepared were confirmed to be a single phase Mn3O4. BET specific surface areas can reach to 32 m2 g−1. The results indicated that products synthesized by aqueous solution oxidation method had higher specific surface areas and smaller particle size than those prepared by means of roasting. However the products prepared using the above two methods showed no obvious differences in magnetic property.

OBTAINING OF VATERITE MICROPARTICLES WITH AN IMMOBILIZED ENZYME – CATALASE BY CO- SYNTHESIS

2020 ◽  
pp. 84-86
Author(s):  
N. Balabushevich ◽  
D. Volodkin ◽  
N. Eremeev ◽  
N. Klyachko
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Immobilized Enzyme ◽  
High Specific Surface Area ◽  
Polymorphic Modifications

Among the polymorphic modifications of CaCO3, vaterite attracts much attention due to its unique properties such as a high specific surface area, controlled particle size [1], and it is also one of the most popular carriers for the manufacture of microparticles in biotechnology and medicine [2].

scholarly journals Synthesis and Characterization of Mn–C–CodopedTiO2Nanoparticles and Photocatalytic Degradation of Methyl Orange Dye under Sunlight Irradiation

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Wei Xin ◽  
Duanwei Zhu ◽  
Guanglong Liu ◽  
Yumei Hua ◽  
Wenbing Zhou
Keyword(s):  
Particle Size ◽  
Methyl Orange ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Visible Region ◽  
High Specific Surface Area ◽  
Size Analysis ◽  
Manganese Acetate ◽  
Sunlight Irradiation

Novel visible-light-active Mn–C–TiO2nanoparticles were synthesized by modified sol-gel method based on the self-assembly technique using polyoxyethylenes orbitan monooleate (Tween 80) as template and carbon precursor and manganese acetate as manganese precursor. The samples were characterized by XRD, FTIR, UV-vis diffuse reflectance, XPS, and laser particle size analysis. The XRD results showed that Mn–C–TiO2sample exhibited anatase phase and no other crystal phase was identified. High specific surface area, small crystallite size, and small particle size distribution could be obtained by manganese and carbon codoped and Mn–C–TiO2exhibited greater red shift in absorption edge of samples in visible region than that of C–TiO2and pure TiO2. The photocatalytic activity of synthesized catalyst was evaluated by photocatalytic oxidation of methyl orange (MO) solution under the sunlight irradiation. The results showed that Mn–C–TiO2nanoparticles have higher activity than other samples under sunlight, which could be attributed to the high specific surface area, smaller particle size, and lower band gap energy.

scholarly journals The Effects of Vinegar Processing on the Changes in the Physical Properties of Frankincense Related to the Absorption of the Main Boswellic Acids

Molecules ◽  
2019 ◽  
Vol 24 (19) ◽  
pp. 3453
Author(s):  
Dongrui Liang ◽  
Zhangchi Ning ◽  
Zhiqian Song ◽  
Chun Wang ◽  
Yuanyan Liu ◽  
...  
Keyword(s):  
Particle Size ◽  
Surface Morphology ◽  
Physical Properties ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Performance ◽  
Analysis Method ◽  
Boswellic Acids ◽  
Main Components

Boswellic acids (BAs), as the main components of frankincense, exhibit notable anti-inflammatory properties. However, their pharmaceutical development has been severely limited by their poor oral bioavailability. Traditional Chinese medicinal processing, called Pao Zhi, is believed to improve bioavailability, yet the mechanism is still completely unclear. Previous research suggested that the bioavailability of a drug can be influenced by physical properties. This paper was designed to investigate the physical properties of frankincense and processed frankincense, including the surface morphology, particle size, polydispersity index (PDI), zeta potential (ZP), specific surface area, porosity, and viscosity. The differences in the intestinal absorption characteristics and equilibrium solubilities between frankincense and processed frankincense were determined by an ultra-high-performance liquid chromatography coupled with a triple quadrupole electrospray tandem mass spectrometry (UHPLC-TQ-MS) analysis method. The results showed that vinegar processing can alter the surface morphology, decrease the particle size and PDI, raise the absolute values of the ZP, specific surface area and porosity, and drop the viscosity of frankincense. Meanwhile, the rates of absorption and dissolution of the main BAs were increased after the processing of frankincense. The present study proves that the physical properties were changed after processing, in which case the bioavailability of frankincense was enhanced.

scholarly journals Nanoporous Quasi-High-Entropy Alloy Microspheres

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 345 ◽  
Author(s):  
Lianzan Yang ◽  
Yongyan Li ◽  
Zhifeng Wang ◽  
Weimin Zhao ◽  
Chunling Qin
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Hierarchical Porous

High-entropy alloys (HEAs) present excellent mechanical properties. However, the exploitation of chemical properties of HEAs is far less than that of mechanical properties, which is mainly limited by the low specific surface area of HEAs synthesized by traditional methods. Thus, it is vital to develop new routes to fabricate HEAs with novel three-dimensional structures and a high specific surface area. Herein, we develop a facile approach to fabricate nanoporous noble metal quasi-HEA microspheres by melt-spinning and dealloying. The as-obtained nanoporous Cu30Au23Pt22Pd25 quasi-HEA microspheres present a hierarchical porous structure with a high specific surface area of 69.5 m2/g and a multiphase approximatively componential solid solution characteristic with a broad single-group face-centered cubic XRD pattern, which is different from the traditional single-phase or two-phase solid solution HEAs. To differentiate, these are named quasi-HEAs. The synthetic strategy proposed in this paper opens the door for the synthesis of porous quasi-HEAs related materials, and is expected to promote further applications of quasi-HEAs in various chemical fields.

KCl-assisted activation: Moringa oleifera branch-derived porous carbon for high performance supercapacitor

2021 ◽  
Vol 45 (12) ◽  
pp. 5712-5719
Author(s):  
Yongxiang Zhang ◽  
Peifeng Yu ◽  
Mingtao Zheng ◽  
Yong Xiao ◽  
Hang Hu ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Porous Carbon ◽  
High Performance ◽  
Moringa Oleifera ◽  
High Specific Surface Area ◽  
Porous Carbons

Porous carbons with a high specific surface area (2314–3470 m2 g−1) are prepared via a novel KCl-assisted activation strategy for high-performance supercapacitor.

Sign in / Sign up

Export Citation Format

Share Document