Hybrid Alkali Activated Concretes - Conception and Development for Practical Application

2016 ◽  
Vol 249 ◽  
pp. 3-7 ◽  
Author(s):  
Vlastimil Bílek ◽  
Jan Hurta ◽  
Petra Done ◽  
Libor Zidek ◽  
Tomas Zajdlik
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Mineral Admixtures ◽  
Alkali Activation ◽  
Granulated Blast Furnace Slag ◽  
Mineral Additions ◽  
New Type ◽  
Furnace Slag ◽  
Alkali Activated

Hybrid cements represent a relatively new type of binders which combine some of the advantages of Ordinary Portland Cement (OPC), the application of mineral admixtures and alkali activation. Hybrid cements represent blends containing a low portion of OPC and a high proportion of mineral additions (such as blast furnace slag, fly ash, metakaolin ....). The paper is focused on the study of properties of mortars prepared from hybrid cements. Mortars with hybrid cements were prepared for an evaluation of the effects of the dosage and the composition of alkali activator, the dosage of OPC and the ratio between ground granulated blast furnace slag and fly ash. The results make it possible to optimize the composition of hybrid alkali activated concretes.

Hybrid Cements with Non Silicate Activators

2017 ◽  
Vol 259 ◽  
pp. 30-34 ◽  
Author(s):  
Vlastimil Bílek ◽  
Filip Khestl ◽  
Pavel Mec
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Mineral Admixtures ◽  
Alkali Activation ◽  
Granulated Blast Furnace Slag ◽  
Mineral Additions ◽  
New Type ◽  
Furnace Slag

Hybrid cements represent a relatively new type of binders which combines some of the advantages of Ordinary Portland Cement and an application of mineral admixtures and alkali activation. Hybrid cements form then blends containing a low portion of OPC and a high proportion of mineral additions (such as blast furnace flag, fly ash, metakaoline, ...). This paper discusses the properties of mortars based on carbonate based activators. Mixtures composed from Ordinary Portland Cement, ground granulated blast furnace slag, fly ash and mechanically pre-activated fly ash were optimised with the target to achieve sufficient compressive strength. The influence of ratios between powder compounds, the dosage of activator and water to binder ratios are presented.

scholarly journals Effect of Mineral Admixtures on the Performance of Low-Quality Recycled Aggregate Concrete

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 596
Author(s):  
Yasuhiro Dosho
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Mineral Admixtures ◽  
Structural Concrete ◽  
Aggregate Concrete ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

To improve the application of low-quality aggregates in structural concrete, this study investigated the effect of multi-purpose mineral admixtures, such as fly ash and ground granulated blast-furnace slag, on the performance of concrete. Accordingly, the primary performance of low-quality recycled aggregate concrete could be improved by varying the replacement ratio of the recycled aggregate and using appropriate mineral admixtures such as fly ash and ground granulated blast-furnace slag. The results show the potential for the use of low-quality aggregate in structural concrete.

Comparison of Selected Properties of Portland Cement Based Materials and Alkali Activated Materials Based on Granulated Blast Furnace Slag

2016 ◽  
Vol 865 ◽  
pp. 107-113 ◽  
Author(s):  
Pavel Mec ◽  
Jana Boháčová ◽  
Josef Koňařík
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Water Glass ◽  
Sodium Metasilicate ◽  
Alkali Activation ◽  
Granulated Blast Furnace Slag ◽  
Cement Based Materials ◽  
One Year ◽  
Furnace Slag ◽  
Alkali Activated

Alkali activated systems are materials formed by alkali-activation of latent hydraulic or pozzolanic materials. The outcome is a polymeric structure with properties comparable to materials based on cement.The principle of the experiment is to compare selected properties of alkali-activated materials based on blast furnace slag and using various types of activator (sodium water glass, potassium water glass, DESIL AL and sodium metasilicate) to binders based on white and Portland cements of the highest quality. The samples were left for one year in environments simulating the conditions in the interior and exterior. Selected physical-mechanical properties were evaluated and compared.

Experimental Study on Compound Binding Material of Alkali Activated Metakaolin and Ground Granulated Blast Furnace Slag

2011 ◽  
Vol 287-290 ◽  
pp. 1275-1279
Author(s):  
Yong Jia He ◽  
Lin Nu Lu ◽  
Shu Guang Hu
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Hydration Product ◽  
Alkali Activation ◽  
Granulated Blast Furnace Slag ◽  
Binding Material ◽  
Measurement Results ◽  
Furnace Slag ◽  
Alkali Activated

Compound binding material was prepared by the alkali activation of metakaolin and ground granulated blast furnace slag. Hydration product components, microstructure and mechanical properties of the hardened paste were investigated by IR, XRD, SEM, MIP, and compressive strength measurement. Results indicated that hydration products included C-S-H and geopolymer, and both of them were amorphous although there were differences in their structure and morphology. When the dosage of slag was less than 50%, the compressive strength of hardened paste increased as the dosage increased, which was mainly because C-S-H produced by the reaction of GGBFS and alkali filled void in geopolymer phase, and part of unreacted slag particles acting as microaggregate to prevent from extension of microcrack in the hardened paste, so the porosity of hardened paste decreased and compressive strength increased.

The Leachability of Heavy Metals from Alkali-Activated Fly Ash and Blast Furnace Slag Matrices

2016 ◽  
Vol 851 ◽  
pp. 141-146
Author(s):  
Jan Koplík ◽  
Miroslava Smolková ◽  
Jakub Tkacz
Keyword(s):  
Mechanical Properties ◽  
Heavy Metals ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Inductively Coupled Plasma ◽  
Emission Spectrometry ◽  
Alkali Activation ◽  
Furnace Slag ◽  
Alkali Activated

The ability of alkali-activated materials (AAMs) to fix and immobilize heavy metals was investigated. Two raw materials were used to prepare alkali-activated matrices – high-temperature fly ash and blast furnace slag (BFS). NaOH served as an alkaline activator. Two heavy metals (Mn, Ni) were added in different amounts to find out the influence of dosage of heavy metal on the mechanical properties of the matrices and the leachability. Leachability was measured as concentration of heavy metals in leachates (ČSN EN 12457-4) by inductively coupled plasma/optical emission spectrometry (ICP/OES). Structure of prepared matrices was characterized by scanning electron microscopy (SEM). Increasing of addition of heavy metals led to decrease of mechanical properties of matrices. The leaching tests showed, that both matrices can immobilize Mn and Ni in dosages of 0.1 – 2,5%. Higher dosages caused deterioration of the matrices and increased the leachability. After alkali activation both heavy metals were transformed into the form of insoluble salts.

Immobilization of Sr2+, Bi3+ and Zn2+ in Alkali-Activated Materials Based on Blast Furnace Slag and Fly Ash

2018 ◽  
Vol 761 ◽  
pp. 15-18 ◽  
Author(s):  
Jan Koplík ◽  
Tomáš Solný ◽  
Lukáš Kalina ◽  
Jiří Másilko
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Alkali Activation ◽  
Alkaline Activator ◽  
Insoluble Compounds ◽  
Furnace Slag ◽  
Alkali Activated ◽  
State Of Metals

It is well known, that alkali-activated materials (AAMs) are suitable for immobilization of heavy metals and other hazardous materials. This study is focused on the characterization of inhibition of three metals – Sr2+, Bi3+and Zn2+in alkali-activated matrices. Two type of matrices were prepared – alkali-activated blast furnace slag (BFS) and alkali-activated fly ash (FA). Sodium water glass was used as alkaline activator. The ability of these matrices to fix the metals were proved by leaching tests. Compressive strength was measured to characterize mechanical properties of the matrices. Scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS) was used to examine distribution and chemical state of metals within the matrices. The observed metals mainly formed the insoluble compounds after alkali activation.

Sign in / Sign up

Export Citation Format

Share Document