Fabrication and Characterization of Bi1.6Pb0.4Sr2Ca2Cu3-xFexOy Superconductor

2017 ◽  
Vol 268 ◽  
pp. 311-314 ◽  
Author(s):  
M.A. Suazlina ◽  
H. Azhan ◽  
S. Akmal Syamsyir ◽  
K. Azman ◽  
W.A.W. Razali ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Undoped Sample ◽  
Fe Doping ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Oxide Powders ◽  
Fabrication And Characterization ◽  
Scanning Electron

This paper reports the properties of Bi-2223 superconductors that had been doped with Fe2O3 at Cu-site of the system. It was prepared in bulk form using high purity oxide powders via solid state reaction technique with intermediate grinding. A series of x = 0.00, 0.02, 0.04, 0.06, 0.08 and 0.10 of Fe were stoichiometrically added to the well balanced of Bi1.6Pb0.4Sr2Ca2Cu3-xFexOy in order to trace the effect of Fe doping. Hence, electrical resistivity, X-ray diffraction and Field Emission Scanning Electron Microscopy have been carried out to assess the effects of Fe doping. These measurements indicate that Fe doping decreased the critical temperature and degrade the formation of high Tc phase compared with the undoped sample. The orthorhombicity parameters were increased due to substitution of Cu 3+ ion by Fe 2+ ion.

Structural, Morphological, Optical and Electrical Properties of Bulk (0001) GaN:Fe Wafers

MRS Advances ◽  
2018 ◽  
Vol 3 (3) ◽  
pp. 179-184
Author(s):  
M. Gaddy ◽  
V. Kuryatkov ◽  
V. Meyers ◽  
D. Mauch ◽  
J. Dickens ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Hydride Vapor Phase Epitaxy ◽  
Optical And Electrical Properties ◽  
Fe Doping ◽  
X Ray Diffraction ◽  
X Ray ◽  
Growth Method ◽  
Secondary Ion ◽  
Scanning Electron

ABSTRACTCharacterization of three vendor’s bulk semi-insulating GaN:Fe wafers, grown by either hydride vapor phase epitaxy or the ammonothermal method, was performed using: scanning electron microscopy, secondary ion mass spectroscopy, high resolution X-ray diffraction, cathodoluminescence, photoluminescence, and high voltage testing. Although the Fe doping level is significantly different for each growth method, both are promising for the fabrication of PCSS devices operating in the lock-on mode.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Hydrothermal Synthesis and Characterization of BiFeO3 Polyhedral Crystallites

2012 ◽  
Vol 174-177 ◽  
pp. 508-511
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

BiFeO3 polyhedrons had been successfully synthesized via a hydrothermal method. The as-prepared products were characterized by power X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The possible mechanisms for the formation of BiFeO3 polyhedrons were discussed. Though comparison experiments, it was found that the kind of precursor played a key role on the morphology control of BiFeO3 crystals.

Characterization of a coating for radioprotection, by X-ray diffraction, scanning electron microscopy, and dispersive energy spectroscopy

2022 ◽  
Vol 321 ◽  
pp. 126326
Author(s):  
Gladis Aparecida Galindo Reisemberger de Souza ◽  
Ramón Sigifredo Cortés Paredes ◽  
Frieda Saicla Barros ◽  
Gustavo Bavaresco Sucharski ◽  
Sebastião Ribeiro Junior ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

scholarly journals Synthesis and characterization of apatite silicated powders with wet precipitation method

2021 ◽  
Vol 234 ◽  
pp. 00106
Author(s):  
Houda Labjar ◽  
Hassan Chaair
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Analytical Techniques ◽  
Precipitation Method ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wet Precipitation ◽  
Scanning Electron

The synthesis of apatite silicated Ca10(PO4)6-x(SiO4)x(OH)2-x (SiHA) with 0≤x≤2 was investigated using a wet precipitation method followed by heat treatment using calcium carbonate CaCO3 and phosphoric acid H3PO4 and silicon tetraacetate SiC8H20O4 (TEOS) in medium of water ethanol, with three different silicate concentrations. After drying, the samples are ground and then characterized by different analytical techniques like X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning electron Microscopy (SEM) and chemical analysis.

Synthesis and characterization of homogeneous lead-substituted tin oxide with the (110) face of rutile structure

2000 ◽  
Vol 15 (10) ◽  
pp. 2076-2079
Author(s):  
Chika Nozaki ◽  
Takashi Yamada ◽  
Kenji Tabata ◽  
Eiji Suzuki
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rutile Structure ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Synthesis of a rutile-type lead-substituted tin oxide with (110) face was investigated. The characterization was performed by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy, x-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller surface area measurements. The homogeneous rutile-type lead-substituted tin oxide was obtained until 4.1 mol% of tin was substituted with lead. The surface of obtained oxide had a homogeneously lead-substituted (110) face.

Sign in / Sign up

Export Citation Format

Share Document