A Numerical Investigation of the Influence of the Blade–Vortex Interaction on the Dynamic Stall Onset

2021 ◽  
Author(s):  
Camille Castells ◽  
François Richez ◽  
Michel Costes
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Dynamic Stall ◽  
Test Case ◽  
Vortex Interaction ◽  
Fluid Structure ◽  
Speed Test ◽  
Vortex Model ◽  
Flow Parameters ◽  
Blade Vortex Interaction

Recently, fluid–structure coupling simulations of helicopter rotors in high-thrust forward flight suggested that dynamic stall might be triggered by the blade–vortex interaction. However, no clear evidence of a correlation between dynamic stall and blade–vortex interaction has yet been given. We propose in this paper a simplified two-dimensional numerical model that can be used to indicate the role that the blade–vortex interaction plays in dynamic stall onset for different flight conditions. In this model, the rotor blade element is considered in pitching oscillation motion with a nonuniform translation, and a simplified vortex model can be introduced or not in the simulation to highlight the effect of blade–vortex interaction. All flow parameters of this simplified model are deduced from data provided by previous three-dimensional high-fidelity fluid–structure simulations. The method is used for validation and analysis of three flight conditions. The results show that, for the two cases with moderate advance ratio, the dynamic stall event is only triggered when a blade–vortex interaction occurs in the stall region. For the high-speed test case, the dynamic stall event seems to be only triggered by the very high angle of attack due to the motion of the blade.

Pressure feedback-based blade–vortex interaction noise controller for helicopter rotors

2018 ◽  
Vol 17 (3) ◽  
pp. 295-318 ◽  
Author(s):  
Sara Modini ◽  
Giorgio Graziani ◽  
Giovanni Bernardini ◽  
Massimo Gennaretti
Keyword(s):  
High Harmonic ◽  
Three Dimensional ◽  
Rotor Blades ◽  
Aerodynamic Noise ◽  
Vortex Interaction ◽  
Noise Sources ◽  
Power Requirement ◽  
Blade Vortex Interaction ◽  
Pressure Feedback ◽  
Helicopter Main Rotor

With the aim of alleviating the noise annoyance emitted by blade–vortex interactions occurring on helicopter main rotors, the present work presents a methodology suitable for the identification of a multi-cyclic harmonic controller based on the actuation of rotor blades equipped with Miniature Trailing Edge Effectors. The objective of the control methodology is the direct suppression of the aerodynamic noise sources by generation of localized high-harmonic blade–vortex interaction counter-actions. The set-up of control devices is selected on the basis of the blade–vortex interaction scenario, taking into account a trade-off between effectiveness and power requirement. The control law is efficiently identified by means of an optimal controller synthesized through suitable two-dimensional multi-vortex, parallel blade–vortex interaction problems. The proposed methodology is validated by the application to realistic helicopter main rotors during low-speed descent flights, numerically simulated through high-fidelity aerodynamic and aeroacoustic solvers based, respectively, upon a three-dimensional free-wake boundary element method to solve the potential flow around rotors in blade–vortex interaction conditions and the Farassat 1A formulation. Results concerning the capability of the proposed controller to alleviate the blade–vortex interaction noise emitted by a realistic helicopter main rotor are presented and discussed.

Development and validation of a hybrid method for predicting helicopter rotor impulsive noise

2018 ◽  
Vol 233 (4) ◽  
pp. 1323-1339 ◽  
Author(s):  
Liangquan Wang ◽  
Guohua Xu ◽  
Yongjie Shi
Keyword(s):  
Hybrid Method ◽  
High Speed ◽  
Stokes Equations ◽  
Impulsive Noise ◽  
Computational Cost ◽  
Helicopter Rotor ◽  
Aerodynamic Load ◽  
Vortex Interaction ◽  
Blade Vortex Interaction ◽  
Hybrid Solver

Prediction of helicopter rotor impulsive noise is practically a very challenging task. This paper describes a hybrid method to predict rotor impulsive noise for both high-speed impulsive noise and blade–vortex interaction noise. The hybrid solver has been developed by combining the advantages of three different methods: (1) a computational fluid dynamics method based on Reynolds-averaged Navier–Stokes equations to account for the viscous and compressible effects near the blade; (2) a vorticity transport model to predict rotor wake system without artificial dissipation; and (3) an acoustic calculation method, based on Ffowcs-Williams Hawkings equation implemented to a permeable data surface. The developed hybrid solver is validated through available test data, for the cases of UH-1H model rotor, AH-1 Operational Loads Survey rotor, and Helishape 7A rotor. Peak sound pressure level of high-speed impulsive noise is accurately predicted with relative errors less than 7%. Additionally, acoustic waveform of blade–vortex interaction noise is well captured though it is sensitive to small changes in aerodynamic load. It is suggested that present hybrid method is versatile for the prediction of rotor impulsive noise with moderate computational cost.

scholarly journals Vortex Model and Blade Span Influence on Orthogonal Blade-Vortex Interaction Noise

AIAA Journal ◽  
2020 ◽  
Vol 58 (8) ◽  
pp. 3405-3413
Author(s):  
Paul Zehner ◽  
Fabrice Falissard ◽  
Xavier Gloerfelt
Keyword(s):  
Vortex Interaction ◽  
Vortex Model ◽  
Blade Vortex Interaction

Double Helical Synchronous Belt Transmission Design

2014 ◽  
Vol 800-801 ◽  
pp. 672-677
Author(s):  
Jian Hua Guo ◽  
Hong Yuan Jiang ◽  
Yi Zhen Wu ◽  
Wen Ya Chu ◽  
Qing Xin Meng
Keyword(s):  
High Speed ◽  
Contact Point ◽  
Three Dimensional ◽  
Transmission Error ◽  
Transmission Model ◽  
Adjacent Area ◽  
Speed Test ◽  
Finite Element Software ◽  
Timing Belt ◽  
Belt Transmission

The meshing impact noise caused by the gradually engagement between double helical synchronous belt and the pulley was reduced due to its spiral angle effect. Therefore, double helical synchronous belt transmission receives much concern with its excellent characteristics of de-noising, low transmission error and high carrying capacity. The profiles of synchronous belt and belt pulley were studied based on conjugate-curvature high degree contact meshing theory under the circumstance that the pitch of belt and belt pulley are identical. The higher contact strength of the belt teeth and a smaller clearance in the contact point adjacent area were ensured with Hertz contact theory as the synchronous belt is in contact with pulley. And then a conjugated arc tooth profile with two-step contact and three-step adjacent gap infinitesimal was proposed based on the simple easy to processing method, which was adopted as main parameters for double synchronous belt and pulley’s normal teeth profile. The three-dimensional transmission model was built and the static nonlinear contact analysis was done with finite element software ANSYS. Finally, the noise experiment was conducted on the high speed test bench to compare the noise reduction effect between double helical synchronous belt and straight tooth timing belt with the identical end face profile. The simulation and experiment result show that the double helical synchronous belt transmission can reduce noise level by 11dB approximately compared with straight tooth timing belt transmission.

Computational aeroelastic analysis of slowed rotors at high advance ratios

2014 ◽  
Vol 118 (1201) ◽  
pp. 297-313 ◽  
Author(s):  
J. de Montaudouin ◽  
N. Reveles ◽  
M. J. Smith
Keyword(s):  
High Speed ◽  
Rotor Blades ◽  
Vortex Interaction ◽  
Blade Loading ◽  
Blade Vortex Interaction ◽  
Aeroelastic Analysis ◽  
Computational Fluid Dynamics Cfd ◽  
Advance Ratio ◽  
Cfd Method ◽  
Model Rotor

Abstract The aerodynamic and aeroelastic behaviour of a rotor become more complex as advance ratios increase to achieve high-speed forward fight. As the rotor blades encounter large regions of cross and reverse flows during each revolution, strong variations in the local Mach regime are encountered, inducing complex elastic blade deformations. In addition, the wake system may remain in the vicinity of the rotor, adding complexity to the blade loading. The aeroelastic behaviour of a model rotor with advance ratios ranging from 0·5 to 2·0 has been evaluated with aerodynamics provided via a computational fluid dynamics (CFD) method. Significant radial blade-vortex interaction can occur at a high advance ratio; the advance ratio at which this occurs is dependent on the rotor configuration. This condition is accompanied by high vibratory loads, peak negative torsion, and peak torsion and in-plane loads. The high vibratory loading increases the sensitivity of the trim model, so that at some high advance ratios the vibratory loads must be filtered to achieve a trimmed state.

scholarly journals Application of a three-dimensional viscous transonic inverse method to NASA rotor 67

2002 ◽  
Vol 216 (3) ◽  
pp. 243-255 ◽  
Author(s):  
W. T. Tiow ◽  
M Zangeneh
Keyword(s):  
High Speed ◽  
Inverse Method ◽  
Static Pressure ◽  
Three Dimensional ◽  
Test Case ◽  
Shock Formation ◽  
Pressure Loading ◽  
Design Computation ◽  
Computational Fluid Dynamics Cfd ◽  
Blade Geometry

The development and application of a three-dimensional inverse methodology in which the blade geometry is computed on the basis of the specification of static pressure loading distribution is presented. The methodology is based on the intensive use of computational fluid dynamics (CFD) to account for three-dimensional subsonic and transonic viscous flows. In the design computation, the necessary blade changes are determined directly by the discrepancies between the target and initial values, and the calculation converges to give the final blade geometry and the corresponding steady state flow solution. The application of the method is explored using a transonic test case, NASA rotor 67. Based on observations, it is conclusive that the shock formation and its intensity in such a high-speed turbomachinery flow are well defined on the loading distributions. Pressure loading is therefore as effective a design parameter as conventional inverse design quantities such as static pressure. Hence, from an understanding of the dynamics of the flow in the fan in relation to its pressure loading distributions, simple guidelines can be developed for the inverse method in order to weaken the shock formation. A qualitative improvement in performance is achieved in the redesigned fan. The final flowfield result is confirmed by a well-established commercial CFD package.

On the three-dimensional nature of the orthogonal blade–vortex interaction

2006 ◽  
Vol 41 (5) ◽  
pp. 749-761 ◽  
Author(s):  
R. B. Green ◽  
F. N. Coton ◽  
J. M. Early
Keyword(s):  
Three Dimensional ◽  
Vortex Interaction ◽  
Blade Vortex Interaction

Large Motion Visualization and Estimation for Fluid-Structure Simulations

2015 ◽  
Author(s):  
Tzu-Sheng Shane Hsu ◽  
Timothy Fitzgerald ◽  
Vincent Phuc Nguyen ◽  
Balakumar Balachandran
Keyword(s):  
Objective Function ◽  
High Speed ◽  
Flexible Structures ◽  
Three Dimensional ◽  
Optimization Procedure ◽  
Fluid Structure Interactions ◽  
Displacement Fields ◽  
Fluid Structure ◽  
Computational Implementation

Studies of fluid-structure interactions associated with flexible structures such as flapping wings require the capture and quantification of large motions of bodies that may be opaque. As a case study, motion capture of a free flying insect is considered by using three synchronized high-speed cameras. A solid finite element (FE) representation is used as a reference body and successive snapshots in time of the displacement fields are reconstructed via an optimization procedure. One of the original aspects of this work is the formulation of an objective function and the use of shadow matching and strain-energy regularization. With this objective function, the authors penalize the shape differences between silhouettes of the captured images and the FE representation of the deformed body. A similar method with a three-dimensional voxel cloud (VC) reconstruction is also illustrated. Challenges faced in implementing the VC method are discussed and the current computational implementation will also be covered.

Interactional Aerodynamic Analysis of an Asymmetric Lift-Offset Compound Helicopter in Forward Flight

2021 ◽  
Author(s):  
Jan-Arun Faust ◽  
Yong Su Jung ◽  
James Baeder ◽  
André Bauknecht ◽  
Jürgen Rauleder
Keyword(s):  
High Speed ◽  
Stokes Equations ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Particle Image Velocimetry Data ◽  
Operating Conditions ◽  
Test Case ◽  
Forward Flight ◽  
Compound Helicopter ◽  
Thrust And Torque

Recently, an asymmetric lift-offset compound helicopter has been conceptualized at the University of Maryland with the objective of improving the overall performance of a medium-lift utility helicopter. The investigated form of lift-compounding incorporates an additional stubbed wing attached to the fuselage on the retreating side. This design alleviates rotor lift requirements and generates a roll moment that enables increased thrust potential on the advancing side in high-speed forward flight. In this study, a numerical model was developed based on the corresponding experimental test case. Three-dimensional unsteady Reynolds-averaged Navier–Stokes equations were solved on overset grids with computational fluid dynamics–computational structural dynamics (CFD–CSD) coupling using the in-house CPU–GPU heterogeneous Mercury CFD framework. Simulations were performed at high-speed, high-thrust operating conditions and showed satisfactory agreement with the experimental measurements in terms of the cyclic control angles, rotor thrust, and torque values. CFD results indicated that for an advance ratio of 0.5 with a collective pitch of 10.6°, a vehicle lift-to-equivalent-drag ratio improvement of 47% was attainable using 11% wing-lift offset. The CFD-computed flow fields provide insights into the origin of a reverse flow entry vortex that was observed in particle image velocimetry data, and they characterize the wing–rotor interactional aerodynamics.

Influence of Rotation on Dynamic Stall

2013 ◽  
Vol 58 (3) ◽  
pp. 1-9 ◽  
Author(s):  
A. D. Gardner ◽  
K. Richter
Keyword(s):  
Three Dimensional ◽  
Time History ◽  
Turbulence Models ◽  
Dynamic Stall ◽  
Test Case ◽  
Test Cases ◽  
Pitching Moment ◽  
Pitching Motion ◽  
Rotating Blade ◽  
Wind Tunnel Data

A computational investigation of the effect of rotation on two-dimensional (2D) deep dynamic stall has been undertaken, showing that the effect of rotation is to reduce the severity of the pitching moment peak and cause earlier reattachment of the flow. A generic single blade rotor geometry was investigated, which had a pitching oscillation around the quarter-chord axis while in hover, causing angle-driven dynamic stall. The results at the midpoint of the blade have the same Mach number (0.31), Reynolds number (1.15 × 106), and pitching motion (α = 13° ± 7°) as a dynamic stall test case for which significant experimental wind tunnel data and 2D computations exist. The rotating blade is compared with 2D computations and computations using the same blade without rotation at Mach 0.31 and with the same pitching motion. All test cases involve geometries propagating into undisturbed flow with no downwash. The three-dimensional (3D) grid computed without rotation had lower lift at the reference section than for a 2D computation with the same geometric angle of attack time history, and the lift overshoot classically observed for Spalart–Allmaras turbulence models during 2D dynamic stall was significantly reduced in the 3D case. Rotation reduced the strength of the dynamic stall vortex, which reduced the accompanying pitching moment peak by 25%.

Sign in / Sign up

Export Citation Format

Share Document