Numerical Evaluation of Required Ductility and Load Bearing Capacity for Aluminium Alloy Continuous Beams

2009 ◽  
Author(s):  
M. Manganiello ◽  
G. De Matteis ◽  
R. Landolfo ◽  
F.M. Mazzolani
Keyword(s):  
Bearing Capacity ◽  
Aluminium Alloy ◽  
Numerical Evaluation ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Continuous Beams

scholarly journals Numerical evaluation of the plastic hinges developed in headed stud shear connectors in composite beams with profiled steel sheeting

2018 ◽  
Author(s):  
Valentino Vigneri ◽  
Christoph Odenbreit ◽  
Matthias Braun
Keyword(s):  
Bearing Capacity ◽  
Numerical Evaluation ◽  
Composite Beams ◽  
Shear Capacity ◽  
Embedment Depth ◽  
Shear Connector ◽  
Load Bearing Capacity ◽  
Plastic Hinges ◽  
Load Bearing ◽  
Headed Stud

For composite beams using novel steel sheeting, the current Eurocode 4 rules sometimes overestimate the load bearing capacity of the shear connector. This is due to the larger rib heights and the smaller rib widths in comparison with the old studies, which have been carried out to calibrate the current design equations. The RFCS Project “DISCCO” investigated this phenomena and the working group under mandate M515, CEN/TC250/SC4/SC4.T3 is enhancing this equation and working on a proposal to be taken over in the new version of Eurocode 4.The proposed new equation covers the failure behaviour of the shear connection more in detail. The test results show, that the failure consists in a combined concrete cone and stud in bending. Due to the geometry of novel steel sheeting, the load bearing capacity of the headed stud shear connector is no more limited by its shear capacity, but by its bending capacity.A 3D non-linear finite element model is developed and validated through the support of the DISCCO push-out tests. A good agreement between numerical and experimental results in terms of force-slip behaviour is achieved. Special attention of this work lies on the numerical evaluation of the number of plastic hinges ny: a stress-based procedure is presented and the results are compared to the equations presented for new Eurocode 4.The numerical simulations show that the upper plastic hinge moves up as the slip increases due to the progressive crushing of the concrete in the rib. From the parametric study, it turns out that ny is linearly proportional to the embedment depth. Compared to pre-punched hole decking, through-deck welding specimen activates less plastic hinges in the studs because of the higher stiffness provided at the base of the stud.

Ultimate Load Bearing Capacity of Web Members of Lattice Aluminium Structures Made of CHS Profiles

2016 ◽  
Vol 710 ◽  
pp. 351-356
Author(s):  
Djordje Djuricic ◽  
Biljana Scepanovic ◽  
Mitar Misovic ◽  
Dusko Lucic
Keyword(s):  
Bearing Capacity ◽  
Aluminium Alloy ◽  
Ultimate Load ◽  
Tube Wall ◽  
Lattice Structure ◽  
Steel Structures ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Welded Structure ◽  
Connection Type

A joint of lattice aluminium welded structure made of circular hollow sections (CHS) has been analysed. Aluminium alloy EN AW 6082-T6 was used. Calculation of ultimate load bearing capacity of lattice structure web member assumes check of element load bearing capacity for the following calculation situations:- calculation of ultimate load bearing capacity of compressed elements with the influence of buckling,- calculation of ultimate load bearing capacity of compressed elements with the influence of HAZ,- calculation of ultimate load bearing capacity of tensioned elements with the influence of HAZ,- calculation of ultimate element force in truss joint, depending on joint construction.The first three checks are independent of type and characteristics of truss chords. They depend only on elements connection manner and geometrical characteristics of web members. The fourth condition directly depends on relation of chord and web member characteristics, i.e. ratio of their diameters and tube wall thicknesses. The choice of joint geometry, gap between elements in joint as well as joint eccentricity are also important for ultimate force in web member. Check of K-joint ultimate bearing capacity is particularly needed for welded joints due to aluminium strength decrease caused by HAZ (Heat Affected Zone) effect.European standard EN 1999 for aluminium structures design has not defined ultimate load of web members regarding type and characteristics of joint connection.Value of ultimate force in web member of K-joint, depending on connection type, by means of expressions defined in EN 1993-1-8 (Design of steel structures - Part 1-8: Design of joints), has been analysed. Comparative analysis has been done by means of ANSYS modelling, taking into consideration real characteristics of aluminium alloy and ultimate load bearing capacity reduction in the vicinity of weld due to HAZ effect. The main goal of the paper is to analyse capability of expressions from EN 1993-1-8 for steel structures to be used in aluminium structures, having in mind quoted limitations.

Increased load bearing capacity of mechanically joined FRP/metal joints using a pin structured auxiliary joining element

2020 ◽  
Vol 62 (1) ◽  
pp. 55-60
Author(s):  
Per Heyser ◽  
Vadim Sartisson ◽  
Gerson Meschut ◽  
Marcel Droß ◽  
Klaus Dröder
Keyword(s):  
Bearing Capacity ◽  
Load Bearing Capacity ◽  
Load Bearing

Load-Bearing Capacity of Direct Inlay-Retained Fibre-reinforced Composite Fixed Partial Dentures with Different Cross-Sectional Pontic Design

2017 ◽  
Vol 68 (1) ◽  
pp. 94-100
Author(s):  
Oana Tanculescu ◽  
Adrian Doloca ◽  
Raluca Maria Vieriu ◽  
Florentina Mocanu ◽  
Gabriela Ifteni ◽  
...  
Keyword(s):  
Bearing Capacity ◽  
Fracture Pattern ◽  
Load Bearing Capacity ◽  
Cross Sectional ◽  
Load Bearing ◽  
Reinforced Composite ◽  
Polyethylene Fibre

The load-bearing capacity and fracture pattern of direct inlay-retained FRC FDPs with two different cross-sectional designs of the ponticwere tested. The aim of the study was to evaluate a new fibre disposition. Two types of composites, Filtek Bulk Fill Posterior Restorative and Filtek Z250 (3M/ESPE, St. Paul, MN, USA), and one braided polyethylene fibre, Construct (Kerr, USA) were used. The results of the study suggested that the new tested disposition of the fibres prevented in some extend the delamination of the composite on buccal and facial sides of the pontic and increased the load-bearing capacity of the bridges.

scholarly journals The energy absorption behavior of novel composite sandwich structures reinforced with trapezoidal latticed webs

2021 ◽  
Vol 60 (1) ◽  
pp. 503-518
Author(s):  
Juan Han ◽  
Lu Zhu ◽  
Hai Fang ◽  
Jian Wang ◽  
Peng Wu
Keyword(s):  
Bearing Capacity ◽  
Energy Absorption ◽  
Sandwich Structure ◽  
Ultimate Load ◽  
Sandwich Structures ◽  
Elastic Displacement ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Composite Sandwich ◽  
Composite Sandwich Structures

Abstract This article proposed an innovative composite sandwich structure reinforced with trapezoidal latticed webs with angles of 45°, 60° and 75°. Four specimens were conducted according to quasi-static compression methods to investigate the compressive behavior of the novel composite structures. The experimental results indicated that the specimen with 45° trapezoidal latticed webs showed the most excellent energy absorption ability, which was about 2.5 times of the structures with vertical latticed webs. Compared to the traditional composite sandwich structure, the elastic displacement and ultimate load-bearing capacity of the specimen with 45° trapezoidal latticed webs were increased by 624.1 and 439.8%, respectively. Numerical analysis of the composite sandwich structures was carried out by using a nonlinear explicit finite element (FE) software ANSYS/LS-DYNA. The influence of the thickness of face sheets, lattice webs and foam density on the elastic ultimate load-bearing capacity, the elastic displacement and initial stiffness was analyzed. This innovative composite bumper device for bridge pier protection against ship collision was simulated to verify its performance. The results showed that the peak impact force of the composite anti-collision device with 45° trapezoidal latticed webs would be reduced by 17.3%, and the time duration will be prolonged by about 31.1%.

Sign in / Sign up

Export Citation Format

Share Document