Analysis of Biodiesel Spray Combustion in Internal-Combustion Engine using Multidimensional Models

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Qiuyu Zheng ◽  
Xu Wang ◽  
Yi Liu ◽  
Feng Jiang ◽  
Tianqi Liu
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Phase Control ◽  
Combustion Characteristics ◽  
Liquid Fuels ◽  
Spray Combustion ◽  
Dimensional Model ◽  
Fuel Temperature ◽  
Ic Engine

With the rapid scale expansion of the first generation of bio-liquid fuels, its impact on the prices of agricultural products, food security and the environment has begun to emerge and attracted extensive attention from governments and academia. A new multi-dimensional model of biodiesel spray combustion in an internal combustion (IC) engine is designed. Firstly, the BP neural network mining model is used to extract the spray combustion data of the IC engine. Then, based on the combustion data of biodiesel load in an internal combustion engine, burning rate and heat release, the principle of spray combustion of biodiesel is analyzed. Finally, from the two aspects of gas-phase control and liquid phase control, a multi-dimensional model of biodiesel spray combustion in IC engine is established and the spray combustion characteristics of biodiesel in IC engine are analyzed. The research results show that the model can effectively analyze the effect of load and fuel temperature on the spray combustion characteristics of biodiesel and the results of the model are almost the same as the actual data and the calculation accuracy is high. It is an effective method for studying the spray combustion characteristics of biodiesel.

scholarly journals Recovery of Exhaust Waste Heat for ICE Using the Beta Type Stirling Engine

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Wail Aladayleh ◽  
Ali Alahmer
Keyword(s):  
Internal Combustion Engine ◽  
Waste Heat ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Stirling Engine ◽  
Gas Temperature ◽  
Ic Engine ◽  
Exhaust Waste Heat ◽  
Useful Power ◽  
Shaft Power

This paper investigates the potential of utilizing the exhaust waste heat using an integrated mechanical device with internal combustion engine for the automobiles to increase the fuel economy, the useful power, and the environment safety. One of the ways of utilizing waste heat is to use a Stirling engine. A Stirling engine requires only an external heat source as wasted heat for its operation. Because the exhaust gas temperature may reach 200 to 700°C, Stirling engine will work effectively. The indication work, real shaft power and specific fuel consumption for Stirling engine, and the exhaust power losses for IC engine are calculated. The study shows the availability and possibility of recovery of the waste heat from internal combustion engine using Stirling engine.

Effect of IC Engine Operating Conditions on Combustion and Emission Characteristics

1993 ◽  
Vol 115 (4) ◽  
pp. 694-701 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Ic Engine ◽  
Pollutants Emission ◽  
Good Agreement

Numerical simulation of flow, combustion, heat release rate, and pollutants emission characteristics have been obtained using a single cylinder internal combustion engine operating with propane as the fuel. The data show that for good agreement with experimental results on the peak pressure and the rate of pressure rise as a function of crank angle, spark ignition energy and local cylinder pressure must be properly modeled. The results obtained for NO and CO showed features which are qualitatively in good agreement and are similar to those reported in the literature for the chosen combustion chamber geometry. The results have shown that both the combustion chamber geometry and engine operating parameters affects the flame growth within the combustion chamber which subsequently affects the pollutants emission levels. The code employed the time marching procedure and solves the governing partial differential equations of multicomponent chemically reacting fluid flow by finite difference method. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

Computation of the Turbulent Flow in an Internal Combustion Engine During Compression

1981 ◽  
Vol 103 (1) ◽  
pp. 75-81 ◽  
Author(s):  
P. S. Bernard
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Dimensional Model ◽  
Vorticity Field ◽  
Dynamical Equations ◽  
Compression Stroke ◽  
Dominant Feature ◽  
Mean And Variance ◽  
The Mean

A set of closed dynamical equations for the mean and variance of the turbulent vorticity field are used to study the piston driven flow in a two-dimensional model of an internal combustion engine cyclinder during the compression stroke. A dominant feature of the flow is observed to be the development of large corner vortices. In their vicinity intense production of turbulence occurs which locally greatly exceeds that resulting from the compression of intake generated turbulence. A comparison of the flow field at two strokes to bore ratios is made.

scholarly journals A 3D modelling of the in-cylinder combustion dynamics of two stroke internal combustion engine in its service condition

2020 ◽  
Vol 39 (1) ◽  
pp. 161-172 ◽  
Author(s):  
A.E. Ikpe ◽  
I.B. Owunna
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Maximum Shear Stress ◽  
Fuel Mixture ◽  
Internal Combustion ◽  
Maximum Temperature ◽  
Ideal Condition ◽  
Gas Temperature ◽  
Ic Engine ◽  
Combustion Dynamics

In this study, a two stroke internal combustion engine was successfully modeled as a closed cycle with the intake, compression, expansion and exhaust processes considered in two strokes of the reciprocating piston. The in-cylinder combusted gases with respect to air-fuel mixture of 14.4:1 in the two stroke engine model were analyzed, showing the dynamics of the combusted gases, the flame pressure and temperature trajectories. It was observed that provided compression and expansion takes place at air-fuel mixture near ideal condition (14.7:1), the combusted gas temperature which occurred in the range of 293.92-3000.60 K is directly proportional to the cylinder gas pressure which occurred in the range of 60.76-80.20 bar. With a heat transfer coefficient of 581.236 W/m2K, the maximum temperature of the IC engine material was found to be 2367.56K at equilibrium and the maximum shear stress was found to be 176 x 102 MPa (1.76 x 105 bar). The 14.4:1 air-fuel mixture implies that 26% O2, 73% N2 and 1% trace gases are the in-cylinder air constituent that will react with 1 mole of hydrocarbon to form the combusted products of 96.2% CO2, 3.2% H2O and 0.6% N2. This will vary in conditions where the air-fuel mixture changes. Keywords: Modelling, Gas dynamics, Two stroke, IC engine, Air-fuel mixture.

Application of Silica-Gel-Reinforced Aluminium Composite on the Piston of Internal Combustion Engine

2018 ◽  
pp. 63-98 ◽  
Author(s):  
Anuj Dixit
Keyword(s):  
Internal Combustion Engine ◽  
Aluminium Alloy ◽  
Silica Gel ◽  
Tribological Properties ◽  
Combustion Engine ◽  
Base Material ◽  
Internal Combustion ◽  
Aluminium Composite ◽  
Ic Engine ◽  
Mechanical And Tribological Properties

The piston of the internal combustion engine is one of the most complex parts among all engine components. During the operation, the pistons of IC engines are typically subjected to high loading and wearing. To withstand these, they require high mechanical properties and excellent tribological properties. This chapter aims to compare the mechanical as well as tribological properties of silica-gel-reinforced aluminium composite with aluminium alloy, which is used in manufacturing of piston of IC engine. Initially silica-gel-reinforced aluminium composite was fabricated with base material aluminium and six different percentages of silica gel reinforcement by stir casting method. After that, mechanical and tribological properties of silica-gel-reinforced aluminium composite were estimated and the tremendous mechanical and tribological properties among all percentages by different optimization techniques were found. The authors then compared the admirable properties of aluminium composite with aluminium alloy for manufacturing of piston of IC engine.

scholarly journals Diagnosis and Improvement of Combustion Characteristics of Methanol Miniature Reciprocating Piston Internal Combustion Engine

Micromachines ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 96 ◽  
Author(s):  
Gangzhi Tang ◽  
Shuaibin Wang ◽  
Li Zhang ◽  
Huichao Shang
Keyword(s):  
Internal Combustion Engine ◽  
Mechanical System ◽  
Combustion Rate ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Micro Electro Mechanical System ◽  
Combustion Characteristics ◽  
Combustion Stability ◽  
Combustion Duration ◽  
Variation Rate

A micro-reciprocating piston internal combustion engine with liquid hydrocarbon fuel has the potential to supply ultrahigh density energy to micro electro mechanical system because of its high-density energy, simple structure, and mature energy conversion principle. However, the diagnostic test of the combustion characteristics of the micro reciprocating piston internal combustion engine shows that its combustion characteristics are poor, and the combustion rate was lower with the combustion duration of more than 50 °CA. The mean indicated pressure (Pmi) value was only 0.137 MPa, the combustion stability was very poor, and the cycle variation rate of the Pmi was up to 60%. To improve its combustion performance, the method to enhance combustion in micro-space is explored then. Mechanism studies have shown that the pyrolysis reaction of nitromethane and hydrogen peroxide can produce amounts of free radicals OH, with the possibility of improving the combustion of methanol. Therefore, a method for adjusting the composition of methanol fuel to enhance combustion is proposed, and the method is theoretically confirmed. Finally, based on this method, the test was carried out. The results showed that the combustion rate increased and the combustion duration decreased by 6% after adding nitromethane. The power performance was enhanced, and the Pmi value was increased by 30%. The combustion stability was enhanced, and the cycle variation rate of the Pmi was reduced to 16.9%. Nitromethane has a significant effect on improving the combustion characteristics of methanol, and the enhancement of the latter was mainly reflected in the ignition phase of the combustion process. This study indicates that exploring the fuel additive that can increase the concentration of OH radical in the reaction is an effective method to improve the micro-space combustion, which will facilitate the development of micro-piston internal combustion engine to supply energy to a micro electro mechanical system.

scholarly journals PULSE JET INTERNAL COMBUSTION ENGINE

2019 ◽  
Author(s):  
Tim Walshaw
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Circular Motion ◽  
Liquid Fuels ◽  
Light Weight ◽  
Piston Engine ◽  
Jet Engine ◽  
Highly Efficient ◽  
Pulse Jet

This article describes using the pulse jet to create circular motion. Such an engine would be highly efficient, simple and cheap to build, light weight, and could use a wide variety of liquid fuels. Such a pulse jet engine would be a very efficient substitute for the piston engine.

Sign in / Sign up

Export Citation Format

Share Document