scholarly journals A 3D modelling of the in-cylinder combustion dynamics of two stroke internal combustion engine in its service condition

2020 ◽  
Vol 39 (1) ◽  
pp. 161-172 ◽  
Author(s):  
A.E. Ikpe ◽  
I.B. Owunna
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Maximum Shear Stress ◽  
Fuel Mixture ◽  
Internal Combustion ◽  
Maximum Temperature ◽  
Ideal Condition ◽  
Gas Temperature ◽  
Ic Engine ◽  
Combustion Dynamics

In this study, a two stroke internal combustion engine was successfully modeled as a closed cycle with the intake, compression, expansion and exhaust processes considered in two strokes of the reciprocating piston. The in-cylinder combusted gases with respect to air-fuel mixture of 14.4:1 in the two stroke engine model were analyzed, showing the dynamics of the combusted gases, the flame pressure and temperature trajectories. It was observed that provided compression and expansion takes place at air-fuel mixture near ideal condition (14.7:1), the combusted gas temperature which occurred in the range of 293.92-3000.60 K is directly proportional to the cylinder gas pressure which occurred in the range of 60.76-80.20 bar. With a heat transfer coefficient of 581.236 W/m2K, the maximum temperature of the IC engine material was found to be 2367.56K at equilibrium and the maximum shear stress was found to be 176 x 102 MPa (1.76 x 105 bar). The 14.4:1 air-fuel mixture implies that 26% O2, 73% N2 and 1% trace gases are the in-cylinder air constituent that will react with 1 mole of hydrocarbon to form the combusted products of 96.2% CO2, 3.2% H2O and 0.6% N2. This will vary in conditions where the air-fuel mixture changes. Keywords: Modelling, Gas dynamics, Two stroke, IC engine, Air-fuel mixture.

scholarly journals Recovery of Exhaust Waste Heat for ICE Using the Beta Type Stirling Engine

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Wail Aladayleh ◽  
Ali Alahmer
Keyword(s):  
Internal Combustion Engine ◽  
Waste Heat ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Stirling Engine ◽  
Gas Temperature ◽  
Ic Engine ◽  
Exhaust Waste Heat ◽  
Useful Power ◽  
Shaft Power

This paper investigates the potential of utilizing the exhaust waste heat using an integrated mechanical device with internal combustion engine for the automobiles to increase the fuel economy, the useful power, and the environment safety. One of the ways of utilizing waste heat is to use a Stirling engine. A Stirling engine requires only an external heat source as wasted heat for its operation. Because the exhaust gas temperature may reach 200 to 700°C, Stirling engine will work effectively. The indication work, real shaft power and specific fuel consumption for Stirling engine, and the exhaust power losses for IC engine are calculated. The study shows the availability and possibility of recovery of the waste heat from internal combustion engine using Stirling engine.

scholarly journals A quick, simplified approach to the evaluation of combustion rate from an internal combustion engine indicator diagram

2008 ◽  
Vol 12 (1) ◽  
pp. 85-102 ◽  
Author(s):  
Miroljub Tomic ◽  
Slobodan Popovic ◽  
Nenad Miljic ◽  
Stojan Petrovic ◽  
Milos Cvetic ◽  
...  
Keyword(s):  
Internal Combustion Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Practical Applications ◽  
Simplified Approach

In this paper a simplified procedure of an internal combustion engine in-cylinder pressure record analysis has been presented. The method is very easy for programming and provides quick evaluation of the gas temperature and the rate of combustion. It is based on the consideration proposed by Hohenberg and Killman, but enhances the approach by involving the rate of heat transferred to the walls that was omitted in the original approach. It enables the evaluation of the complete rate of heat released by combustion (often designated as ?gross heat release rate? or ?fuel chemical energy release rate?), not only the rate of heat transferred to the gas (which is often designated as ?net heat release rate?). The accuracy of the method has been also analyzed and it is shown that the errors caused by the simplifications in the model are very small, particularly if the crank angle step is also small. A several practical applications on recorded pressure diagrams taken from both spark ignition and compression ignition engine are presented as well.

Analysis of Biodiesel Spray Combustion in Internal-Combustion Engine using Multidimensional Models

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Qiuyu Zheng ◽  
Xu Wang ◽  
Yi Liu ◽  
Feng Jiang ◽  
Tianqi Liu
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Phase Control ◽  
Combustion Characteristics ◽  
Liquid Fuels ◽  
Spray Combustion ◽  
Dimensional Model ◽  
Fuel Temperature ◽  
Ic Engine

With the rapid scale expansion of the first generation of bio-liquid fuels, its impact on the prices of agricultural products, food security and the environment has begun to emerge and attracted extensive attention from governments and academia. A new multi-dimensional model of biodiesel spray combustion in an internal combustion (IC) engine is designed. Firstly, the BP neural network mining model is used to extract the spray combustion data of the IC engine. Then, based on the combustion data of biodiesel load in an internal combustion engine, burning rate and heat release, the principle of spray combustion of biodiesel is analyzed. Finally, from the two aspects of gas-phase control and liquid phase control, a multi-dimensional model of biodiesel spray combustion in IC engine is established and the spray combustion characteristics of biodiesel in IC engine are analyzed. The research results show that the model can effectively analyze the effect of load and fuel temperature on the spray combustion characteristics of biodiesel and the results of the model are almost the same as the actual data and the calculation accuracy is high. It is an effective method for studying the spray combustion characteristics of biodiesel.

Effect of IC Engine Operating Conditions on Combustion and Emission Characteristics

1993 ◽  
Vol 115 (4) ◽  
pp. 694-701 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Ic Engine ◽  
Pollutants Emission ◽  
Good Agreement

Numerical simulation of flow, combustion, heat release rate, and pollutants emission characteristics have been obtained using a single cylinder internal combustion engine operating with propane as the fuel. The data show that for good agreement with experimental results on the peak pressure and the rate of pressure rise as a function of crank angle, spark ignition energy and local cylinder pressure must be properly modeled. The results obtained for NO and CO showed features which are qualitatively in good agreement and are similar to those reported in the literature for the chosen combustion chamber geometry. The results have shown that both the combustion chamber geometry and engine operating parameters affects the flame growth within the combustion chamber which subsequently affects the pollutants emission levels. The code employed the time marching procedure and solves the governing partial differential equations of multicomponent chemically reacting fluid flow by finite difference method. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

Application of Silica-Gel-Reinforced Aluminium Composite on the Piston of Internal Combustion Engine

2018 ◽  
pp. 63-98 ◽  
Author(s):  
Anuj Dixit
Keyword(s):  
Internal Combustion Engine ◽  
Aluminium Alloy ◽  
Silica Gel ◽  
Tribological Properties ◽  
Combustion Engine ◽  
Base Material ◽  
Internal Combustion ◽  
Aluminium Composite ◽  
Ic Engine ◽  
Mechanical And Tribological Properties

The piston of the internal combustion engine is one of the most complex parts among all engine components. During the operation, the pistons of IC engines are typically subjected to high loading and wearing. To withstand these, they require high mechanical properties and excellent tribological properties. This chapter aims to compare the mechanical as well as tribological properties of silica-gel-reinforced aluminium composite with aluminium alloy, which is used in manufacturing of piston of IC engine. Initially silica-gel-reinforced aluminium composite was fabricated with base material aluminium and six different percentages of silica gel reinforcement by stir casting method. After that, mechanical and tribological properties of silica-gel-reinforced aluminium composite were estimated and the tremendous mechanical and tribological properties among all percentages by different optimization techniques were found. The authors then compared the admirable properties of aluminium composite with aluminium alloy for manufacturing of piston of IC engine.

scholarly journals Diesel Internal Combustion Engine Emissions Measurements for Methanol-Based and Ethanol-Based Biodiesel Blends

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Charalambos A. Chasos ◽  
George N. Karagiorgis ◽  
Chris N. Christodoulou
Keyword(s):  
Internal Combustion Engine ◽  
Diesel Fuel ◽  
Combustion Engine ◽  
Fuel Mixture ◽  
Internal Combustion ◽  
Experimental Investigations ◽  
Biodiesel Fuel ◽  
The European Union ◽  
Fuel Blend ◽  
Biodiesel Blends

There is a recent interest for the utilisation of renewable and alternative fuel, which is regulated by the European Union, that currently imposes a lower limit of 7% by volume of biodiesel fuel blend in diesel fuel. The biodiesel physical characteristics, as well as the percentage of biodiesel blend in diesel fuel, affect the injector nozzle flow, the spray characteristics, the resulting air/fuel mixture, and subsequently the combustion quality and emissions, as well as the overall engine performance. In the present study, two different types of pure biodiesel fuel, namely, methanol-based biodiesel and ethanol-based biodiesel, were produced in the laboratory of Frederick University by chemical processing of raw materials. The two biodiesel fuels were used for blending pure diesel fuel at various percentages. The blends were used for smoke emissions measurements of a diesel internal combustion engine at increasing engine speed and for increasing engine temperatures. From the experimental investigations it was found that ethanol-based biodiesel blends result in higher smoke emissions than pure diesel fuel, while methanol-based biodiesel blends smoke emissions are lower compared to pure diesel fuel.

scholarly journals Analysis of Air Flow, Air and Fuel Induction for Internal Combustion Engine

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Mohd Fitri Arshad ◽  
◽  
Muhammad Faris Ahmad ◽  
Amir Khalid ◽  
Izuan Amin Ishak ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Flow Behavior ◽  
Combustion Process ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Internal Combustion ◽  
Spark Ignition Engine ◽  
Rotating Flow

In an internal combustion engine, performance, efficiency and emission formation depends on the formation of air-fuel mixture inside the engine cylinder. The fluid flow dynamics plays an important role for air-fuel mixture preparation to obtain the better engine combustion, performance and efficiency. This review article discuss the rotating flow (swirl and tumble) in premixed spark-ignition engine and its effect on turbulence generation and flame propagation. Rotating flow can substantially increase turbulence intensity for the duration of the combustion period. This review paper discusses the in-cylinder swirl and tumble flow that affects air induction during the combustion process in internal combustion engine. Alternatively, this study using computer simulation (Computational Fluid Dynamic, CFD) which offer the opportunity to carry out repetitive parameter studies. An integration-type flowmeter (IFM) also has been used which consists of ultrasonic flowmeter, that integrates the flowrate during the intake process, gives accurate measurements regardless of sampling time and frequency. Research parameter in this study was swirl and tumble that represents the fluid flow behavior occurred inside combustion chamber. Fuel injection and air mass also were the important parameters that have been discussed about in air induction process. The results obtain from the numerical analysis can be employed to examine the homogeneity of air-fuel mixture structure for better combustion process and engine performance.

Sign in / Sign up

Export Citation Format

Share Document