PERFORMANCE COMPARISON AND OUTDOOR MONITORING OF SMOOTH AND TEXTURED COVER GLASS FOR SOLAR MODULES OF UP 6 YEARS EXPOSED

Solar modules are being built with nearly the same configuration for decades now. The front is covered with a tempered glass pane. The performance of a PV module can be increased by the texturation of the front side. One of the major requirements for front cover glasses is their high optical transmission. One option to boost transmission is texturing the front surface in a similar manner to crystalline solar cell. Another advantage of a textured glass is the fact that the reflected light beam at normal incidence has a second chance of being transmitted to the solar cell. Furthemore, the texturation of front cover glass might collect more dust and soiling than a flat glass surface. Due to this concern, the soiling effect of module covered with textured cover Alberino P glass after long-term exposed will investigated in this work. The modules presented in this work have the same characteristics in STC (i.e short circuit current, open circuit voltage and maximum power point). Electroluminescence, I-V and P-V characteristic are the method used to detect faults on the PV module. The results show a loss of PV performance with textured cover glass is l,72% higher than the reference module in other hand the increase of serie resistance is also observed in both modules

Download Full-text

Improvement of short circuit current of mono crystalline silicon solar cells

Science and Technology Development Journal ◽

10.32508/stdj.v16i1.1418 ◽

2013 ◽

Vol 16 (1) ◽

pp. 48-56

Author(s):

Vu Ngoc Hoang ◽

Linh Ngoc Tran ◽

Lan Truong ◽

Khoa Thanh Nhat Phan ◽

Chien Mau Dang ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Indium Tin Oxide ◽

Crystalline Silicon ◽

Short Circuit ◽

Front Surface ◽

Short Circuit Current ◽

Open Circuit ◽

Crystalline Silicon Solar Cell ◽

Antireflection Coatings

In this report we present series of experiments during which the short circuit current of mono crystalline silicon solar cell was improved step by step so as a consequence the efficiency was increased. At first, the front contact of solar cell was optimized to reduce the shadow loss and the series resistance. Then surface treatments were prepared by TMAH solution to reduce the total light reflectance and to improve the light trapping effect. Finally, antireflection coatings were deposited to passivate the front surface either by silicon nitride thin layer or to increase the collection probability by indium tin oxide layer, and to reduce the reflectance of light. As a result, solar cells of about 13% have been obtained, with the average open circuit voltage Voc about 527mV, with the fill factor about 68% and the short circuit current about 7.92 mA/cm2 under the irradiation density of 21 mW/cm2.

Download Full-text

CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽

10.3390/en14061684 ◽

2021 ◽

Vol 14 (6) ◽

pp. 1684

Author(s):

Alessandro Romeo ◽

Elisa Artegiani

Keyword(s):

Thin Film ◽

Solar Cells ◽

Solar Cell ◽

Short Circuit ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Early Years ◽

Solar Cell Efficiency ◽

Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

Download Full-text

GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽

10.3390/cryst11070726 ◽

2021 ◽

Vol 11 (7) ◽

pp. 726

Author(s):

Ray-Hua Horng ◽

Yu-Cheng Kao ◽

Apoorva Sood ◽

Po-Liang Liu ◽

Wei-Cheng Wang ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Low Temperature ◽

Triple Junction ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Metal Line ◽

Solar Simulator ◽

Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

Download Full-text

Enhancement of the performance of CdS/CdTe heterojunction solar cell using TiO2/ZnO bi-layer ARC and V2O5 BSF layers: A simulation approach

The European Physical Journal Applied Physics ◽

10.1051/epjap/2020200213 ◽

2020 ◽

Vol 92 (2) ◽

pp. 20901

Author(s):

Abdul Kuddus ◽

Md. Ferdous Rahman ◽

Jaker Hossain ◽

Abu Bakar Md. Ismail

Keyword(s):

Solar Cell ◽

Short Circuit ◽

Photovoltaic Performance ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Heterojunction Solar Cell ◽

Back Surface ◽

Heterojunction Solar Cells

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.

Download Full-text

17.8%-efficient Amorphous Silicon Heterojunction Solar Cells on p-type Silicon Wafers

MRS Proceedings ◽

10.1557/proc-0910-a26-05 ◽

2006 ◽

Vol 910 ◽

Cited By ~ 2

Author(s):

Qi Wang ◽

Matt P. Page ◽

Eugene Iwancizko ◽

Yueqin Xu ◽

Yanfa Yan ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Amorphous Silicon ◽

High Efficiency ◽

Short Circuit ◽

Open Circuit ◽

Layer Growth ◽

Surface Recombination Velocity ◽

Back Contact ◽

P Type

AbstractWe have achieved an independently-confirmed 17.8% conversion efficiency in a 1-cm2, p-type, float-zone silicon (FZ-Si) based heterojunction solar cell. Both the front emitter and back contact are hydrogenated amorphous silicon (a-Si:H) deposited by hot-wire chemical vapor deposition (HWCVD). This is the highest reported efficiency for a HWCVD silicon heterojunction (SHJ) solar cell. Two main improvements lead to our most recent increases in efficiency: 1) the use of textured Si wafers, and 2) the application of a-Si:H heterojunctions on both sides of the cell. Despite the use of textured c-Si to increase the short-circuit current, we were able to maintain the same 0.65 V open-circuit voltage as on flat c-Si. This is achieved by coating a-Si:H conformally on the c-Si surfaces, including covering the tips of the anisotropically-etched pyramids. A brief atomic H treatment before emitter deposition is not necessary on the textured wafers, though it was helpful in the flat wafers. It is essential to high efficiency SHJ solar cells that the emitter grows abruptly as amorphous silicon, instead of as microcrystalline or epitaxial Si. The contact on each side of the cell comprises a thin (< 5 nm) low substrate temperature (~100°C) intrinsic a-Si:H layer, followed by a doped layer. Our intrinsic layers are deposited at 0.3-1.2 nm/s. The doped emitter and back-contact layers were deposited at a higher temperature (>200°C) and grown from PH3/SiH4/H2 and B2H6/SiH4/H2 doping gas mixtures, respectively. This combination of low (intrinsic) and high (doped layer) growth temperatures was optimized by lifetime and surface recombination velocity measurements. Our rapid efficiency advance suggests that HWCVD may have advantages over plasma-enhanced (PE) CVD in fabrication of high-efficiency heterojunction c-Si cells; there is no need for process optimization to avoid plasma damage to the delicate, high-quality, Si wafers.

Download Full-text

Prediction of Solar Irradiance Based on Artificial Neural Networks

Inventions ◽

10.3390/inventions4030045 ◽

2019 ◽

Vol 4 (3) ◽

pp. 45 ◽

Cited By ~ 4

Author(s):

Waleed I. Hameed ◽

Baha A. Sawadi ◽

Safa J. Al-Kamil ◽

Mohammed S. Al-Radhi ◽

Yasir I. A. Al-Yasir ◽

...

Keyword(s):

Neural Networks ◽

Artificial Neural Networks ◽

Solar Irradiance ◽

Open Circuit Voltage ◽

Low Cost ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Pv Module ◽

Artificial Neural

Prediction of solar irradiance plays an essential role in many energy systems. The objective of this paper is to present a low-cost solar irradiance meter based on artificial neural networks (ANN). A photovoltaic (PV) mathematical model of 50 watts and 36 cells was used to extract the short-circuit current and the open-circuit voltage of the PV module. The obtained data was used to train the ANN to predict solar irradiance for horizontal surfaces. The strategy was to measure the open-circuit voltage and the short-circuit current of the PV module and then feed it to the ANN as inputs to get the irradiance. The experimental and simulation results showed that the proposed method could be utilized to achieve the value of solar irradiance with acceptable approximation. As a result, this method presents a low-cost instrument that can be used instead of an expensive pyranometer.

Download Full-text

Effective Light Harvesting of Tandem Polymer Solar Cell

Journal of Solar Energy Engineering ◽

10.1115/1.4001150 ◽

2010 ◽

Vol 132 (2) ◽

Cited By ~ 5

Author(s):

Yi-Chun Chen ◽

Chao-Ying Yu ◽

Chih-Ping Chen ◽

Shu-Hua Chan ◽

Ching Ting

Keyword(s):

Solar Cell ◽

Molecular Orbital ◽

Open Circuit Voltage ◽

Polymer Solar Cell ◽

Short Circuit ◽

Active Material ◽

Weight Ratio ◽

Acid Methyl Ester ◽

Open Circuit ◽

Ito Glass

A novel soluble conjugated polymers, P2, with coplanar thiophene-phenylene-thiophene unit is designed and synthesized as suitable active material used in tandem cells to compensate the poly(3-hexylthiophene) (P3HT)/[6,6]-phenyl-C71 butyric acid methyl ester (PC71BM) bulk-heterojunction cell in this paper. P2 polymer bears advantages in both low optical bandgap (1.7 eV) and high hole mobility properties (3.4×10−3 cm2/V-s from field-effect transistor measurement). Furthermore, the electrochemical studies of P2 indicate desirable highest occupied molecular orbital/lowest unoccupied molecular orbital (HOMO/LUMO) band structure that enables a high open circuit voltage when pairing with PCBM acceptor. The best power conversion efficiency of this polymer solar cell thus far based on P2/PC71BM system with a weight ratio of 1:3 reached 4.4% with a short circuit current density (Jsc) of 10.2 mA/cm2, an open circuit voltage (Voc) of 0.81 V, and a fill factor (FF) of 0.53 under air mass (AM) 1.5 G (100 mW/cm2). The preliminary data of the tandem cell with indium tin oxide (ITO) glass/PEDOT:PSS/P2:PC71BM/TiOx/PEDOT:PSS/P3HT:PC71BM/TiOx/Al configuration has reached Jsc of 6.2 mA/cm2, Voc of 1.33 V, FF of 0.56 and an overall efficiency of 4.6% under AM 1.5 G (100 mW/cm2).

Download Full-text

An Improved Triple-Tandem Organic Solar Cell

MRS Proceedings ◽

10.1557/proc-1212-s03-19 ◽

2009 ◽

Vol 1212 ◽

Author(s):

Dewei Zhao ◽

Xiao Wei Sun ◽

Lin Ke ◽

Swee Tiam Tan

Keyword(s):

Solar Cell ◽

Small Molecule ◽

Organic Solar Cells ◽

Organic Solar Cell ◽

Copper Phthalocyanine ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Solar Irradiation ◽

The Third

AbstractWe present an efficient polymer-small molecule triple-tandem organic solar cell (OSC), consisting of poly(3-hexylthiophene) (P3HT) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6)C61 (PCBM) bulk heterojunction as the first and second cells, and small molecules copper phthalocyanine (CuPc) and fullerene (C60) as the third cell on top. These sub-cells are connected by an intermediate layer of Al(1 nm)/MoO3(15 nm), which appears to be highly transparent, structurally smooth, and electrically functional. Compared to our previous all polymer triple-tandem organic solar cells (2.03%), this polymer-small molecule triple-tandem organic solar cell achieves an improved power conversion efficiency of 2.18% with a short-circuit current density (Jsc) = 3.02 mA/cm2, open-circuit voltage (Voc) = 1.51 V, and fill factor (FF) = 47.7% under simulated solar irradiation of 100 mW/cm2 (AM1.5G), which can be attributed to the increased photocurrent generation in the third cell since the third cell has the complementary absorption with two bottom cells despite a slightly reduced Voc.

Download Full-text

Characterization and Treatment of Titanium Dioxide via Ultrasonic Process withMelastoma malabathricumas Sustainable Sensitizer for Photovoltaic Solar Cell

Journal of Chemistry ◽

10.1155/2013/251741 ◽

2013 ◽

Vol 2013 ◽

pp. 1-10 ◽

Cited By ~ 4

Author(s):

Anika Zafiah M. Rus ◽

Nur Munirah Abdullah ◽

M. F. L. Abdullah

Keyword(s):

Solar Cell ◽

Metal Oxide ◽

Short Circuit ◽

Open Circuit ◽

Hydroxyl Groups ◽

High Porosity ◽

Enhanced Absorption ◽

Melastoma Malabathricum ◽

Atomic Force ◽

Ultrasonic Process

Generation from the existing commercial devices costs about ten times more than the conventional methods. Therefore, this paper presents a thin-film dyed solar cell (DSC) of natural dyes fromMelastoma malabathricumfruits which consist of the carbonyl and hydroxyl groups of anthocyanin molecule that influences the performance of photosensitized effect due to its bound on the surface of filler. Experimental results comparing engineering grade (>99% purity) of metal oxide; U1 and U2 with treated metal oxide; U3 and U4 using ultrasonic process, which is to break the particle agglomeration from 0.37 μm down to 0.15 μm; this treatment led to a more “sponge-like” consistency with high porosity, enabling enhanced absorption and anchorage of the dye sensitizer. The microstructures of metal oxide were observed using Field Emission Scanning Electron Microscope (FESEM) and Atomic Force Microscope (AFM). Along with the highest performance ofI-Vmeasurement given by U4 with open circuit,Voc = 0.742 V, short circuit,Isc = 0.36 mA, fill factor, FF = 57.012 gives 0.039% efficiency the examples for the first outdoor application upon sunlight illumination of such DSC were also reported. Therefore, this ultrasonic treatment and novel dye fromMelastoma malabathricumfruit are reliable to be used for further application.

Download Full-text

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.665.330 ◽

2013 ◽

Vol 665 ◽

pp. 330-335 ◽

Cited By ~ 1

Author(s):

Ripal Parmar ◽

Dipak Sahay ◽

R.J. Pathak ◽

R.K. Shah

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Fill Factor ◽

Short Circuit ◽

Short Circuit Current ◽

Electrical Energy ◽

Open Circuit ◽

Cell Parameters ◽

Photoelectrochemical Solar Cell ◽

Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

Download Full-text