scholarly journals An Evaluation of Shear Bond Strength of Self-Etch Adhesive on Pre-etched Enamel: An in vitro Study

2013 ◽  
Vol 14 (6) ◽  
pp. 1036-1038
Author(s):  
Abdul Mujeeb ◽  
Bhadra Rao ◽  
Satti Narayana Reddy ◽  
Kanchan Mehta ◽  
G Saritha

ABSTRACT Aim To determine the shear bond strength of self-etch adhesive G-bond on pre-etched enamel. Materials and methods Thirty caries free human mandibular premolars extracted for orthodontic purpose were used for the study. Occlusal surfaces of all the teeth were flattened with diamond bur and a silicon carbide paper was used for surface smoothening. The thirty samples were randomly grouped into three groups. Three different etch systems were used for the composite build up: group 1 (G-bond self-etch adhesive system), group 2 (G-bond) and group 3 (Adper single bond). Light cured was applied for 10 seconds with a LED unit for composite buildup on the occlusal surface of each tooth with 8 millimeters (mm) in diameter and 3 mm in thickness. The specimens in each group were tested in shear mode using a knife-edge testing apparatus in a universal testing machine across head speed of 1 mm/ minute. Shear bond strength values in Mpa were calculated from the peak load at failure divided by the specimen surface area. The mean shear bond strength of all the groups were calculated and statistical analysis was carried out using one-way Analysis of Variance (ANOVA). Results The mean bond strength of group 1 is 15.5 Mpa, group 2 is 19.5 Mpa and group 3 is 20.1 Mpa. Statistical analysis was carried out between the groups using one-way ANOVA. Group 1 showed statistically significant lower bond strength when compared to groups 2 and 3. No statistical significant difference between groups 2 and 3 (p < 0.05). Conclusion Self-etch adhesive G-bond showed increase in shear bond strength on pre-etched enamel. How to cite this article Rao B, Reddy SN, Mujeeb A, Mehta K, Saritha G. An Evaluation of Shear Bond Strength of Self-Etch Adhesive on Pre-etched Enamel: An In vitro Study. J Contemp Dent Pract 2013;14(6):1036-1038.

2010 ◽  
Vol 04 (04) ◽  
pp. 367-373 ◽  
Author(s):  
Sevi Burcak Cehreli ◽  
Asli Guzey ◽  
Neslihan Arhun ◽  
Alev Cetinsahin ◽  
Bahtiyar Unver

Objectives: The aim of this in vitro study is to determine (1) shear bond strength (SBS) of brackets bonded with self-etch and total-etch adhesive after ozone treatment (2) bond failure interface using a modified Adhesive Remnant Index (ARI).Methods: 52 premolars were randomly assigned into four groups (n=13) and received the following treatments: Group 1: 30 s Ozone (Biozonix, Ozonytron, Vehos Medikal, Ankara, Turkey) application + Transbond Plus Self-Etching Primer (SEP) (3M) + Transbond XT (3M), Group 2: Transbond Plus SEP + Transbond XT, Group 3: 30 s Ozone application + 37% orthophosphoric acid + Transbond XT Primer (3M) + Transbond XT, Group 4: 37% orthophosphoric acid + Transbond XT Primer + Transbond XT. All samples were stored in deionised water at 37oC for 24 hours. Shear debonding test was performed by applying a vertical force to the base of the bracket at a cross-head speed of 1 mm/min.Results: The mean SBS results were Group 1: 10.48 MPa; Group 2: 8.89 MPa; Group 3: 9.41 MPa; Group 4: 9.82 MPa. One-Way Variance Test revealed that the difference between the groups was not statistically significant (P=0.267). Debonded brackets were examined by an optical microscope at X16 magnification to determine the bond failure interface using a modified ARI. The results were (mean) Group 1: 2.38; Group 2: 1.31; Group 3: 3.00; Group 4: 1.92. Multiple comparisons showed that Groups 1 and 2, 2 and 3, 3 and 4 were statistically different (P=0.014, P<.001 and P=0.025).Conclusions: Ozone treatment prior to bracket bonding does not affect the shear bond strength. (Eur J Dent 2010;4:367-373)


2007 ◽  
Vol 77 (4) ◽  
pp. 701-706 ◽  
Author(s):  
Rodney G. Northrup ◽  
David W. Berzins ◽  
Thomas Gerard Bradley ◽  
William Schuckit

Abstract Objective: To evaluate and compare the shear bond strengths of two adhesives using two types of brackets: a conventional and a self-ligating bracket system. Materials and Methods: Sixty extracted human premolars were collected. The premolars were randomly divided into three groups of 20 teeth. All three groups were direct bonded. Groups 1 and 2 used light-cured adhesive and primer (Transbond XT) with a conventional (Orthos) and a self-ligating bracket (Damon 2), respectively. Group 3 used a light-cured primer (Orthosolo) and a light-cured adhesive (Blūgloo) with a self-ligating bracket (Damon 2). The specimens were stored in distilled water at 37°C for 40 ± 2 hours, after which they were debonded and inspected for Adhesive Remnant Index (ARI) scoring. Results: The mean shear bond strength was 15.2 MPa for group 1, 23.2 MPa for group 2, and 24.8 MPa for group 3. A one-way analysis of variance and post hoc Tukey test showed significant differences in bond strength (P &lt; .001) between group 1 and groups 2 and 3 but no significant difference (P &gt; .05) between groups 2 and 3. A Weibull analysis demonstrated that all three groups provided sufficient bond strength with over 90% survival rate at normal masticatory and orthodontic force levels. A Kruskal-Wallis test showed no significant difference (P &gt; .05) in ARI scores among all three groups. Conclusions: All three groups demonstrated clinically acceptable bond strength. The Damon 2 self-ligating bracket exhibited satisfactory in vitro bond strength with both adhesive systems used.


2015 ◽  
Vol 5 (2) ◽  
pp. 65-68
Author(s):  
Shruti Patil ◽  
Prajna Shetty

ABSTRACT Background The dentin desensitizers available for in-office application for prevention and/or treatment of post restorative dentinal hypersensitivity, act by blocking the open dentinal tubules. In doing so, they may influence the bond strength of the restorative resins. Thus, the aim of the study was to evaluate the effect of desensitizers on the shear bond strength of dentin adhesives and to check the extent of dentinal tubule occlusion caused by these desensitizers. Materials and Methods Sixty-four premolars were randomly divided into four groups of sixteen each. The middle depth dentin was exposed by on the buccal surface and was etched using 37% phosphoric acid and rinsed. They were assigned to, Group 1: Gluma desensitizer, Group 2: Vivasens desensitizer, Group 3: Gluma Comfort Bond and desensitizer, and Group 4: Adper Single Bond 2. Composite resin post of 2 mm in height and width were built on these specimens. The samples were then mounted in acrylic resin blocks. Universal testing machine was used to test the shear bond strength. The data were analyzed using one-way analysis of variance (ANOVA) and post hoc Tukey's test. Results The mean values of the shear bond strength were for: Group 1—18.61 ± 1.03 MPa, Group 2—17.53 ± 1.36 MPa, Group 3—22.63 ± 1.61 MPa and Group 4—23.12 ± 1.02 MPa. There was a statistically significant difference (p < 0.05) among the groups. Conclusion The use of dentin desensitizers’ influences bond strength between the tooth and the adhesive. Among the various agents, the single bottle system containing Gluma comfort bond and desensitizer had the best adhesion among the desensitizer groups. How to cite this article Patil S, Naik B, Shetty P. A Comparative Evaluation of Three Commercially Available Dentin Desensitizers on the Shear Bond Strength of Composite Resins: An in vitro Study. J Contemp Dent 2015;5(2):65-68.


2009 ◽  
Vol 10 (2) ◽  
pp. 67-74 ◽  
Author(s):  
Hacer Deniz Arisu ◽  
Hüma Ömürlü ◽  
Evrim Eligüzeloğlu ◽  
Mine Üçtaşli

Abstract Aim The aim of this study was to evaluate the effects of multiple consecutive coatings of a one-step self-etch adhesive system (Clearfil Tri-S Bond) on the microtensile bond strength (MBS) to dentin. Methods and Materials Nine caries-free human lower third molars were sectioned perpendicular to the long axis to expose the mid-coronal dentin. The teeth were separated into three experimental groups (n=3) according to the number of adhesive resin coats applied. In Group 1 one layer of Clearfil Tri-S Bond was applied according to the manufacturer's instructions. In Group 2 and Group 3 the adhesive was applied in two and three layers, respectively. In these two groups the first layer was applied according to the manufacturer's instructions but the second and third layers of adhesive were not light cured after application. After the placement of the composite, the teeth were sectioned to obtain approximately 1 mm2 beams for testing. Eighteen beams were prepared for each group using the ‘non-trimming’ method. The MBS values of all specimens were tested, and fracture modes were then determined using a stereomicroscope. Results The mean MBS values (in MPa) of Group 1 (one coat of the adhesive) was significantly lower (p=0.04) than those of Group 3 (three applied coats of the adhesive). There were no statistically significant differences between Groups 1 and 2 and Groups 2 and 3. Conclusion Within the limitations of this in vitro study the application of multiple coats of a one-step self-etch adhesive may provide an increase in bond strength compared to the application of only one coat of adhesive. Clinical Significance Three consecutive coats of one-step self-etching adhesive application can improve MBS. Citation Arisu HD, Eligüzeloğlu E, Üçtaşli M, Ömürlü H. Effect of Multiple Consecutive Applications of One-step Self-etch Adhesive on Microtensile Bond Strength. J Contemp Dent Pract 2009 March; (10)2:067-074.


2003 ◽  
Vol 14 (2) ◽  
pp. 132-135 ◽  
Author(s):  
Claudia Minami Kussano ◽  
Gerson Bonfante ◽  
José Gilmar Batista ◽  
João Henrique Nogueira Pinto

This study evaluated the shear bond strength of porcelain/composite using 40 metal + porcelain + composite cylindrical specimens divided into 4 groups, according to porcelain surface treatment: 1) no treatment, 2) mechanical retentions performed with diamond burs, 3) etching with phosphoric acid+silane, and 4) etching with hydrofluoric acid+silane. After being stored in distilled water at room temperature for one week, the specimens were submitted to a shear force (load) and the data were analyzed statistically (ANOVA). The means (in Mpa) of the groups were: 4.71 (group 1); 4.81 (group 2); 11.76 (group 3); 11.07 (group 4). There were no statistically significant differences between groups 1 and 2 and between groups 3 and 4.


2016 ◽  
Vol 20 (2) ◽  
pp. 99-103
Author(s):  
Katerina Zlatanovska ◽  
Ljuben Guguvcevski ◽  
Risto Popovski ◽  
Cena Dimova ◽  
Ana Minovska ◽  
...  

Summary Background: The aim of this in vitro study was to examine the fracture load of composite veneers using three different preparation designs. Material and methods: Fifteen extracted, intact, human maxillary central incisors were selected. Teeth were divided into three groups with different preparation design: 1) feather preparation, 2) bevel preparation, and 3) incisal overlap- palatal chamfer. Teeth were restored with composite veneers, and the specimens were loaded to failure. The localization of the fracture was recorded as incisal, gingival or combined. Results: Composite veneers with incisal overlap - palatal chamfer showed higher fracture resistance compared to feather preparation and bevel preparation. The mean (SD) fracture loads were: Group 1: 100.6±8.0 N, Group 2: 107.4±6.8 N, and Group 3: 122.0±8.8 N. The most common mode of failure was debonding for veneers with feather preparation and fracture when incisal edge is reduced. The most frequent localization of fracture was incisal. Conclusion: The type of preparation has a significant effect on fracture load for composite veneers. This study indicates that using an incisal overlap- palatal chamfer preparation design significantly increases the fracture resistance compared to feather and bevel preparation designs.


2013 ◽  
Vol 14 (5) ◽  
pp. 790-795 ◽  
Author(s):  
G Vinay Kumar ◽  
Basanagouda S Patil ◽  
BK Raghavendra Rao ◽  
SM Sharathchandra ◽  
Reshma Hegde

ABSTRACT Aim The aim of the present study was to investigate the effectiveness of the one total-etch self-priming adhesive, one two-step self-etching primer adhesive, and one ‘all-in-one’ selfetching adhesive system on the adhesion of a resin composite to enamel. Materials and methods Thirty-six freshly extracted human mandibular molars were selected for this study. A flat area about 5 mm in diameter was created on the exposed mesial surface of enamel of each tooth by moist grinding with 320, 420 and 600 grit silicon carbide paper. Twelve teeth were randomly assigned into three groups. In group 1, Adper Easy One (3M ESPE), a one step self-etching primer adhesive was applied and light curing unit for 10 seconds. In group 2, Adper SE Plus, a twostep self-etching primer with bottle A containing the aqueous primer and bottle B containing the acidic adhesive was applied and light cured for 10 seconds. Group 3 (control)—etchant 37% phosphoric acid is applied to the surface for 15 seconds and rinsed with water and air dried and adhesive (single bond 2) is applied to the surface and tube is placed and light cured for 20 seconds. Composite material (Z350) was placed in the tube and light cured for 40 seconds in all the groups. Bond strength testing was done using universal testing machine at the enamel-composite interface. The debonded enamel surface was evaluated in stereomicroscope to assess the cohesive, adhesive or mixed fracture. Data was statistically analyzed by one way analysis of variance (ANOVA). Results Group 1 performed least among all groups with a mean score of 19.46 MPa. Group 2 had a mean score of 25.67 MPa. Group 3 had a mean score of 27.16 MPa. Conclusion Under the conditions of this in vitro study, the bond strength values of the two-step self-etching primer systems tested were similar to the total-etch. And, one step self-etching primers have lower bond strength compared to the total-etch. How to cite this article Patil BS, Rao BKR, Sharathchandra SM, Hegde R, Kumar GV. Comparative Evaluation of Selfetching Primers and Phosphoric Acid Effectiveness on Composite to Enamel Bond: An in vitro Study. J Contemp Dent Pract 2013;14(5):790-795.


Blood ◽  
2011 ◽  
Vol 118 (21) ◽  
pp. 1500-1500
Author(s):  
Victoria J Weston ◽  
Tracey A Perry ◽  
Katie Brown ◽  
Shaun R Wilson ◽  
Pamela R Kearns

Abstract Abstract 1500 Five year survival rates for childhood AML in children are currently 55–65%. AML is an extremely heterogeneous disease, and while prognostic significance of some karyotypic abnormalities has become evident, the biology of the disease remains largely unknown. Full characterisation of leukaemia initiating cells which may be responsible for relapse has not yet been undertaken. We investigated the leukaemic stem cell populations from 10 childhood primary AML samples by comparing expression of CD34, CD38 and CD45RA, a marker of a committed granulocyte-macrophage progenitor (GMP)-like population frequent in adult AML, in vitro daunorubicin sensitivity and engraftment in immuno-compromised NOD/Shi-scid/IL-2Rgnull (NOG) mice. Consequently, we were able to classify AML samples into 4 subgroups. These comprised Group 1, CD34+CD38- AML (n=1); Group 2, CD34-CD38+CD45RA- (<10% CD34+ blasts) AML (n=4); Group 3, CD34+CD38+CD45RA- (>10% CD34+ blasts) AML (n=4); and Group 4, CD34-CD38+CD45RA+ (<10% CD34+ and >10% CD45RA+ blasts) (n=1). There was no apparent enrichment for high risk prognostic karyotypes in any of the groups. The Group 1 AML presented at 3y with t(16;21); In Group 2 AMLs, the mean presentation age was 11y, 2 carried good prognostic t(8;21), while 1 had MLL involvement and 1 had FLT3-ITD with chromosome 13 isodisomy, both higher risk indicators; The Group 3 AMLs presented with a mean age of 11.9y and 2 carried good prognostic inv(16) whereas 2 had FLT3-ITD one with additional chromosome 13 isodisomy, t(5;11) and TP53 loss. Finally, the Group 4 AML presented at 1.5y with a normal karyotype. When we compared the 2 most frequent subgroups, Group 2 had a much shorter mean EFS of 122d (n=2) compared with a 275d (n=4) for Group 3 (the mean follow up was 282d and 1013.5d, respectively). We next sorted four cell subpopulations based on CD34 and CD38 expression (CD34+CD38-, CD34+CD38+, CD34-CD38- and CD34-CD38+ blasts) and compared in vitro sensitivity to daunorubicin. In Group 1, CD34- and CD34+ cells were equally sensitive at nanomolar IC50 doses. In 2 of the Group 2 AMLs,CD34-CD38- cells were the most resistant to daunorubicin at micromolar IC50 doses (2.5-10mM) whereas the CD34-CD38+ cells (also the dominant subpopulation in this group) were the most sensitive cells exhibiting nanomolar IC50 doses (750–800nM). In contrast, the Group 3 AMLs were overall more sensitive to daunorubicin exhibiting lower nanomolar IC50 doses. Again in this group, the CD34-CD38- cells were typically the most resistant (this time being the dominant subpopulation) whereas the CD34+CD38+ were the most sensitive cells. Finally, in the Group 4 AML, while CD45RA+ cells rapidly underwent spontaneous apoptosis, CD45RA- cells exhibited extreme resistance to daunorubicin (IC50 >10mM) and CD38 expression had no impact on sensitivity. The reduced sensitivity of Group 2 AMLs to daunorubicin compared with Group 3 could, therefore, be an underlying factor contributing to shorter EFS. Finally, we initiated comparison of the stem cell qualities of the different subpopulations from representative samples from each of the two major subgroups, first by assessment of differentiation potential in vitro, and second by engraftment in vivo using NOG mice. In on-going experiments, the time to leukaemia will be compared between mice injected with unsorted and sorted cells and, at terminal cull, cells harvested from organs will be characterised by karyotype and immunophenotype and tested for clonogenic potential via subsequent serial transplantations. Peripheral blood sampling currently suggests higher human CD45+ engraftment in mice injected with sorted versus unsorted cells, and these are CD34+CD33+CD3- recapitulating the AML phenotype. We anticipate that particular subpopulations will be enriched for AML stem cells with the ability to repopulate the leukaemia. Overall, we have shown that childhood AML is diverse with respect to stem cell characteristics. AMLs with low CD34 (Groups 2 and 4) exhibit the greatest overall resistance to daunorubicin as well as shorter EFS. Furthermore, in the majority of AMLs, CD34-CD38- blasts exhibit the least sensitivity to daunorubicin. Novel therapies which can target these resistant subpopulations with leukaemia initiating activity could significantly improve the treatment responses in this clinically challenging disease. Disclosures: No relevant conflicts of interest to declare.


2013 ◽  
Vol 07 (01) ◽  
pp. 055-060 ◽  
Author(s):  
Mehmet Akin ◽  
Sertac Aksakalli ◽  
Faruk Ayhan Basciftci ◽  
Abdullah Demir

ABSTRACTObjective: The purpose of this study was to determine the effect of 10% carbamide peroxide and 38% hydrogen peroxide bleaching agents on the shear bond strength of orthodontic brackets using self-etching primer systems.Methods: Forty five freshly extracted human premolar teeth were randomly divided into 3 groups of 15 teeth each: control (group 1), 10% carbamide peroxide at-home bleached (group 2), and 38% hydrogen peroxide in-office bleached (group 3). Three weeks later, all brackets were bonded using a self-etching primer system. The shear bond strength of these brackets was measured and recorded in MPa. Adhesive remnant index (ARI) scores were determined after the brackets failed. Data were analyzed using Kruskal- Wallis test, pairwise comparisons were made using the Mann-Whitney U test and ARI scores were analyzed using a chi-square test at a significance level of P<.05.Results: The shear bond strengths of group 1 (mean: 17.7 ± 9.7 MPa) were significantly higher (P<.05) than those of group 3 (mean: 9.9 ± 5.4 MPa). No significant differences were found between group 2 (mean: 12.3 ± 4.7) and either group 1 or group 3 (P>.05). ARI scores did not differ significantly among the 3 groups.Conclusions: The use of 10% carbamide peroxide bleaching does not significantly reduce shear bond strength values. In contrast, use of 38% hydrogen peroxide bleaching significantly reduces these values. (Eur J Dent 2013;7:55-60)


2008 ◽  
Vol 78 (2) ◽  
pp. 339-344 ◽  
Author(s):  
Jeff A. Foster ◽  
David W. Berzins ◽  
Thomas G. Bradley

Abstract Objective: To determine whether an amorphous calcium phosphate (ACP)-containing adhesive has an acceptable level of shear bond strength to be used as an orthodontic adhesive. Materials and Methods: Sixty extracted premolars were randomly divided into three groups for orthodontic bonding. Group 1 used a composite resin adhesive (Transbond XT), group 2 was bonded with an ACP-containing adhesive (Aegis Ortho), and group 3 used a resin-modified glass ionomer (Fuji Ortho LC). All bonded teeth were stored in distilled water at 37°C for 40 ± 2 hours prior to debonding. Shear bond strength and adhesive remnant index (ARI) were recorded for each specimen. Results: The mean shear bond strengths for the three test groups were: group 1 (15.2 ± 3.6 MPa), group 2 (6.6 ± 1.5 MPa), and group 3 (8.3 ± 2.8 MPa). A one-way analysis of variance showed a significant difference in bond strengths between the groups. A post hoc Tukey test showed group 1 to be significantly (P &lt; .001) greater than groups 2 and 3. A Kruskal-Wallis test and a Mann-Whitney U-test showed groups 1 and 3 exhibited lower ARI scores than group 2, but a majority of specimens in each group had greater than 50% of the cement removed along with the bracket during debonding. Conclusions: The ACP-containing adhesive demonstrated a low, but satisfactory bond strength needed to function as an orthodontic adhesive.


Sign in / Sign up

Export Citation Format

Share Document