scholarly journals Recent Progress of EMI Reduction Technology on Printed Circuit Board. International Trend of EMI Regulation.

1994 ◽  
Vol 9 (4) ◽  
pp. 235-238
Author(s):  
Kenji SUZUKI
Keyword(s):  
Recent Progress ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Printed Circuit ◽  
Emi Reduction

406. An Ergonomic Hazards Survey of Printed Circuit Board Factories

1999 ◽  
Author(s):  
C. Lu ◽  
S. Wang ◽  
C. Wei ◽  
S. In
Keyword(s):  
Printed Circuit Board ◽  
Circuit Board ◽  
Printed Circuit

Characteristics of Radiated Emission from a Printed Circuit Board with a Slit

2012 ◽  
Vol 132 (6) ◽  
pp. 404-410 ◽  
Author(s):  
Kenichi Nakayama ◽  
Kenichi Kagoshima ◽  
Shigeki Takeda
Keyword(s):  
Printed Circuit Board ◽  
Circuit Board ◽  
Printed Circuit ◽  
Radiated Emission

Confirming the Signal Integrity in Transmission of Digital Signals on Microstrip Straight Circuits via the Eye Diagrams

2014 ◽  
Vol 5 (1) ◽  
pp. 737-741
Author(s):  
Alejandro Dueñas Jiménez ◽  
Francisco Jiménez Hernández
Keyword(s):  
Integrated Circuits ◽  
Printed Circuit Board ◽  
Signal Integrity ◽  
High Volume ◽  
Information Storage ◽  
Circuit Board ◽  
Electromagnetic Simulation ◽  
Electronic Systems ◽  
Digital Signals ◽  
Printed Circuit

Because of the high volume of processing, transmission, and information storage, electronic systems presently requires faster clock speeds tosynchronizethe integrated circuits. Presently the “speeds” on the connections of a printed circuit board (PCB) are in the order of the GHz. At these frequencies the behavior of the interconnects are more like that of a transmission line, and hence distortion, delay, and phase shift- effects caused by phenomena like cross talk, ringing and over shot are present and may be undesirable for the performance of a circuit or system.Some of these phrases were extracted from the chapter eight of book “2-D Electromagnetic Simulation of Passive Microstrip Circuits” from the corresponding author of this paper.

Root Cause Analysis of a Connector Time-Delayed Fracture

2015 ◽  
Author(s):  
Prabjit Singh ◽  
Ying Yu ◽  
Robert E. Davis
Keyword(s):  
Printed Circuit Board ◽  
Ceramic Substrate ◽  
Circuit Board ◽  
Delayed Fracture ◽  
Ceramic Substrates ◽  
Printed Circuit ◽  
Root Cause ◽  
Chip Carrier ◽  
Electrical Connections ◽  
Grain Boundary Grooves

Abstract A land-grid array connector, electrically connecting an array of plated contact pads on a ceramic substrate chip carrier to plated contact pads on a printed circuit board (PCB), failed in a year after assembly due to time-delayed fracture of multiple C-shaped spring connectors. The land-grid-array connectors analyzed had arrays of connectors consisting of gold on nickel plated Be-Cu C-shaped springs in compression that made electrical connections between the pads on the ceramic substrates and the PCBs. Metallography, fractography and surface analyses revealed the root cause of the C-spring connector fracture to be plating solutions trapped in deep grain boundary grooves etched into the C-spring connectors during the pre-plating cleaning operation. The stress necessary for the stress corrosion cracking mechanism was provided by the C-spring connectors, in the land-grid array, being compressed between the ceramic substrate and the printed circuit board.

Application of Lock-in Thermography on PCB for Fault Localization and Validation of Failure Mechanism Due to External Discrete Component Variation

2010 ◽  
Author(s):  
William Ng ◽  
Kevin Weaver ◽  
Zachary Gemmill ◽  
Herve Deslandes ◽  
Rudolf Schlangen
Keyword(s):  
Failure Mechanism ◽  
Integrated Circuit ◽  
Printed Circuit Board ◽  
Hot Spot ◽  
Circuit Board ◽  
Discrete Component ◽  
Printed Circuit ◽  
Thermal Signature ◽  
Lock In

Abstract This paper demonstrates the use of a real time lock-in thermography (LIT) system to non-destructively characterize thermal events prior to the failing of an integrated circuit (IC) device. A case study using a packaged IC mounted on printed circuit board (PCB) is presented. The result validated the failing model by observing the thermal signature on the package. Subsequent analysis from the backside of the IC identified a hot spot in internal circuitry sensitive to varying value of external discrete component (inductor) on PCB.

Sign in / Sign up

Export Citation Format

Share Document