scholarly journals Multi-Response Optimization of process Parameter in Vertical Milling Machine of EN 31 Using Taguchi Method

2021 ◽  
Vol 23 (11) ◽  
pp. 228-235
Author(s):  
Sunil Kumar ◽  
◽  
P.N . Rao ◽  
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Depth Of Cut ◽  
Tool Wear Rate ◽  
Vertical Milling Machine ◽  
En 31

The purpose of this experimental research is to compare the effectiveness of using Taguchi approaches for multi-response optimization of process parameters in Vertical Milling Machine of EN 31 Material intending to minimize surface roughness and tool wear rate while maximizing material removal rate to improve the productivity of the process with coated carbide insert. Taguchi L9 and Annova have been applied for experimental design and analysis. This experiment shows that feed and depth of cut are factors that are important for tool wear, Depth of cut is a notable factor for Material Removal Rate and feed is the most notable factor for surface roughness. Spindle speed has little effect on tool wear rate, surface roughness, and material removal rate. Mathematical models for three response parameters i.e. tool wear rate, surface roughness, and material removal rate were obtained by regression analysis

Optimization of Electric Discharge Machining Parameters of Al-7%Si-4%Mg with 20% of Red Mud Metal Matrix Composites

2014 ◽  
Vol 941-944 ◽  
pp. 1973-1976
Author(s):  
B. Geetha ◽  
K. Ganesan
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electric Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Peak Current ◽  
Pulse On Time

An investigation was carried out to find out the influence of process parameters on surface roughness (SR) and material removal rate (MRR) in electric discharge machine of Al-7%Si-4%Mg with 20% of red mud Metal Matrix Composites since electric discharge machining is a thermo-electric machining process, an electronic die sinking electric discharge machine was used to drill holes in the composite work piece, copper is used as tool material. Experiment was carried out to find surface roughness, material removal rate and tool wear rate by varying the peak current, flushing pressure of dielectric fluid and pulse on time. It was found that the surface roughness of composite metal increases with the increase peak current ,pulse on time and flushing pressure due larger and deeper craters on the drilled surface. It was also found that there was increase in metal removal rate with the increase in peak current and flushing pressure and slightly decreases with the increase in pulse on time due carbon deposits on the electrodes. Experimental analysis is carried using Taguchi’s Design of Experiment method with various parameters like peak current, flushing pressure of dielectric fluid and pulse on time to identify the key factors that influence the surface roughness, material removal rate and tool wear rate. It was found that the peak current was the most significant parameter that influences surface roughness, material removal rate and tool wear rate. The Taguchi experiments results confirm the actual results obtained from the numerical calculation.

ELECTRICAL DISCHARGE MACHINING OF Al/7.5% Al2O3 MMCs USING ROTARY TOOL AND Al2O3 POWDER

2017 ◽  
Vol 24 (02) ◽  
pp. 1750018 ◽  
Author(s):  
SAEED DANESHMAND ◽  
BEHNAM MASOUDI ◽  
VAHID MONFARED
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Pulse Current ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Rotary Tool ◽  
Pulse On Time

Nowadays, composites are used in different parts of industries and it is one of the most important subjects. The most widely used reinforcements in metal matrix composites are Al2O3 and SiC fibers and particles which may be used in cutting-edge functional and structural applications of aerospace, defense, and automobile industries. Depending on the type of powder used, composite materials are difficult to machine by conventional cutting tools and methods. The most appropriate way for machining of these composites is electro discharge. For the reason of improving the surface quality, tool wear rate and material removal rate and reducing the cracks on the surface, Al2O3 powder was used. In this study, the effect of input parameters of EDM such as voltage, pulse current, pulse on-time and pulse off-time on output parameters like material removal rate, tool wear rate and surface roughness in both conditions of the rotary tool with powder mixed dielectric EDM and the stationary tool excluding powder mixed dielectric were investigated. The critical parameters were identified by variance analysis, while the optimum machining parameter settings were achieved via Taguchi method. Results show that using of powder mixed dielectric and rotary tool reduce the tool wear rate, surface roughness and the cracks on the surface significantly. It is found also that using of powder mixed dielectric and rotary tool improve the material removal rate due to improved flushing action and sparking efficiency. The analysis of variance showed that the pulse current and pulse on-time affected highly the MRR, TWR, surface roughness and surface cracks.

Influences of Varying Combination of Feed Rate and Depth of Cut to Tool Wear Rate and Surface Roughness: High Speed Machining Technique in Non-High Speed Milling Machine

2014 ◽  
Vol 903 ◽  
pp. 194-199
Author(s):  
Mohd Zairulnizam Zawawi ◽  
Mohd Ali Hanafiah Shaharudin ◽  
Ahmad Rosli Abdul Manaf
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Tool Wear Rate

Machining technique using high spindle speed, high feed rate and shallow depth of cut utilize in High Speed Milling (HSM) machines offer several benefits such as increase of productivity, elimination of secondary and semi-finishing process, reduce tool load and small chips produced. By adjusting some of the machining parameters, non-HSM machine having lower spindle speed and feed rate could also take advantages some of the benefits mentioned above when applying the HSM technique. This experiment investigate the effects of varying combination of depth of cut and feed rate to tool wear rate and surface roughness during end milling of Aluminum and P20 tool steel in dry condition. The criterion for tool wear before it gets rejected is based on maximum flank wear, Vb of 0.6mm. Material removal rate, spindle speed and radial depth of cut are constant in this experiment. After preliminary machining trials, the combination starts with depth of cut of 2mm and feed rate of 45mm/min until the smallest depth of cut and highest feed rate of 0.03mm and 3000mm/min respectively. The obtained result shows that for both materials, feed rate significantly influences the surface roughness value while depth of cut does not as the surface roughness value keep increasing with the increase of feed rate and decreasing depth of cut. Whereas, tool wear rate almost remain unchanged indicates that material removal rate strongly contribute the wear rate. With no significant tool wear rate, this study demonstrates that HSM technique is possible to be applied in non-HSM machine with extra benefits of eliminating semi-finishing operation, reducing tool load for finishing, machining without coolant and producing smaller chip for ease of cleaning.

scholarly journals Machine Ability Characteristics of PWEDM Process

2019 ◽  
Vol 9 (1) ◽  
pp. 3580-3583
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrical Discharge Machine ◽  
Machining Process ◽  
Work Piece ◽  
Tool Wear Rate

The traditional machining consists of a specific contact between the tool and work piece. As a result of this contact the tool may wear out after a few operations. In addition to that, the MRR (Material Removal Rate), Surface Finish, etc. is also lowered. As a result of these drawbacks, traditional or conventional machining processes cannot be used to machine ceramic based alloys and thus we opt for unconventional machining process. The Electrical Discharge Machine contains of two spaces one is Electrode and other is Work piece. In this concept the among the tool wear rate is moderate and the surface roughness is to be poor. The tool cost is so high. Hence continuously tool modification is not possible. So in the work main objective of the problem is reduced the tool wear rate and increase the MRR. (Material removal rate). So in the case we are consider in the surface roughness. The surface roughness is to be high is the taken in industrial application. So we have focus with surface roughness. These are the considering with in our problems. In our aim is reducing the toll wear and improve the Material Remove rate. In order to addition of graphite in Electrolyte. When added the electrolyte in Graphite the Toll wear rate decrease and increase a material Removal Rate. Finally we have disc the DOE process

scholarly journals Experimental Analysis and Optimization of EDM Parameters on HcHcr Steel in Context with Different Electrodes and Dielectric Fluids Using Hybrid Taguchi-Based PCA-Utility and CRITIC-Utility Approaches

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 419
Author(s):  
Manjunath Patel Gowdru Chandrashekarappa ◽  
Sandeep Kumar ◽  
Jagadish Jagadish ◽  
Danil Yurievich Pimenov ◽  
Khaled Giasin
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Surface Quality ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Distilled Water ◽  
Tool Wear Rate ◽  
Dielectric Fluids

Industries demand stringent requirements towards economical machining without hindering the surface quality while cutting high carbon high chromium (HcHcr) steel. Electrical discharge machining (EDM) of HcHcr steel aims at reducing machining cost (i.e., maximize material removal rate (MRR) and minimize tool wear rate (TWR)) with good surface quality (i.e., minimize surface roughness (SR)). A comparative study was carried out on EDM of HcHcr D2 steel (DIN EN ISO 4957) by applying Taguchi L18 experimental design considering different electrode materials (copper, graphite, and brass), dielectric fluids (distilled water and kerosene), peak current, and pulse-on-time. The process performances were analyzed with respect to material removal rate, surface roughness, and tool wear rate. Pareto analysis of variance was employed to estimate the significance of the process variables and their optimal levels for achieving lower SR and TWR and higher MRR. Hybrid Taguchi-CRITIC-Utility and Taguchi-PCA-Utility methods were implemented to determine the optimal EDM parameters. Higher MRR of 0.0632 g/min and lower SR of 1.68 µm and TWR of 0.012 g/min was attained by graphite electrode in presence of distilled water as dielectric fluid compared to the brass and copper. Additionally, a metallographic analysis was carried out to study the surface integrity on the machined surfaces. Micrographic analysis of the optimal conditions showed lower surface roughness and fewer imperfections (lesser impression, waviness surface, and micro-cracks) compared to worst conditions.

CHARACTERIZATION OF ZrB2-SiC COMPOSITES WITH AN ANALYTICAL STUDY ON MATERIAL REMOVAL RATE AND TOOL WEAR RATE DURING ELECTRICAL DISCHARGE MACHINING

2016 ◽  
Vol 40 (3) ◽  
pp. 331-349 ◽  
Author(s):  
S. Sivasankar ◽  
R. Jeyapaul
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Relative Density ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Tool Materials

This research work concentrates on Electrical Discharge Machining (EDM) performance evaluation of ZrB2- SiC ceramic matrix composites with different tool materials at various machining parameters. Monolithic ZrB2 possesses lower relative density (98.72%) than composites. ZrB2 with 20 Vol.% of SiC possesses 99.74% of the relative density with improved hardness values. Bend strength and Young’s modulus increase with SiC addition until it reaches 20 Vol% and then decreasing. EDM performance on tool materials of tungsten, niobium, tantalum, graphite and titanium at various levels of pulse on time and pulse off time are analyzed. Graphite produces the best Material removal rate (MRR) for all the workpieces. Tool wear rate decreases with melting point and thermal conductivity of the tool material.

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy

2019 ◽  
Vol 233 (12) ◽  
pp. 2283-2291 ◽  
Author(s):  
Arun Kumar Rouniyar ◽  
Pragya Shandilya
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Pulse On Time

Magnetic field assisted powder mixed electrical discharge machining is a hybrid machining process with suitable modification in electrical discharge machining combining the use of magnetic field and fine powder in the dielectric fluid. Aluminum 6061 alloy has found highly significance for the advanced industries like automotive, aerospace, electrical, marine, food processing and chemical due to good corrosion resistance, high strength-to-weight ratio, ease of weldability. In this present work, magnetic field assisted powder mixed electrical discharge machining setup was fabricated and experiments were performed using one factor at a time approach for aluminum 6061 alloy. The individual effect of machining parameters namely, peak current, pulse on time, pulse off time, powder concentration and magnetic field on material removal rate and tool wear rate was investigated. The effect of peak current was found to be dominant on material removal rate and tool wear rate followed by pulse on time, powder concentration and magnetic field. Increase in material removal rate and tool wear rate was observed with increase in peak current, pulse on time and a decrease in pulse off time, whereas, for material removal rate increases and tool wear rate decreases up to the certain value and follow the reverse trend with an increase in powder concentration. Material removal rate was increased and tool wear rate was decreased with increase in magnetic field.

Sign in / Sign up

Export Citation Format

Share Document