scholarly journals High Frequency Solid State Transformer Design Considerations for Power Systems Applications

2021 ◽  
Vol 2 (5) ◽  
Author(s):  
Raton Kumar Nondy ◽  
Md. Abul Bashar ◽  
Prema Nondy ◽  
M. Hazrat Ali
Keyword(s):  
Power Quality ◽  
Power Factor ◽  
Power Distribution ◽  
High Frequency ◽  
Low Voltage ◽  
Voltage Drop ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Power Converter ◽  
Voltage Sag

The conventional power frequency (50 or 60 Hz) transformers are economical, highly reliable and quite efficient but they suffer with certain drawbacks like sensitive to harmonics, voltage drop under load, no protection from system disruptions and overloads, poor performance under dc offset load unbalances and no scope to improve power factor. These transformers with copper wound wires on iron cores are unable to respond to control signals as power generations become distributed and intermittent. So, the need of electronic based regulated power supply with software based remote intelligence has become essential. Also, to easily connect the new energy sources to the grid and to improve the power quality by harmonic filtering, voltage sag correction and highly dynamic control of the power flow, a new type of transformer based on power electronics, known as SST has been introduced. The SST realizes voltage transformation, galvanic isolation, power quality improvements such as instantaneous voltage regulation, voltage sag compensation and power factor correction. It is a collection of high-powered semiconductor components, high frequency power transformer and control circuitry which is used to provide a high level of flexible control to power distribution networks. The SST is a high frequency switched Power Electronic Devices (PEDs) based transformer with high controllability that enables flexible connectivity between existing medium voltage power distribution network, low voltage AC residential system and envisioned DC residential system. In this paper a systematic constructional detail of a SST with a power rating of 2 kVA, operating frequency of 20 kHz and voltage rating of 600/60 V as a scaled-down prototype used for power converter topologies is presented. The design is simple and it avoids the difficulty of choosing massive amounts of empirical parameters.

Unit Template Based Control of PV-DSTATCOM

2020 ◽  
Vol 13 (1) ◽  
pp. 36-42
Author(s):  
Gunjan Varshney ◽  
Durg S. Chauhan ◽  
Madhukar P. Dave ◽  
Nitin
Keyword(s):  
Power Quality ◽  
Power Factor ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Phase Distribution ◽  
Voltage Regulation ◽  
Photovoltaic Array ◽  
Quality Issues ◽  
Static Compensator

Background: In modern electrical power distribution systems, Power Quality has become an important concern due to the escalating use of automatic, microprocessor and microcontroller based end user applications. Methods: In this paper, power quality improvement has done using Photovoltaic based Distribution Static Compensator (PV-DSTATCOM). Complete simulation modelling and control of Photovoltaic based Distribution Static Compensator have been provided in the presented paper. In this configuration, DSTATCOM is fed by solar photovoltaic array and PV module is also helpful to maintain the DC link voltage. The switching of PV-STATCOM is controlled by Unit template based control theory. Results: The performance of PV-DSTATCOM has been evaluated for Unity Power Factor (UPF) and AC Voltage Control (ACVC) modes. Here, for studying the power quality issues three-phase distribution system is considered and results have been verified through simulation based on MATLAB software. Conclusion: Different power quality issues and their improvement are studied and presented here for harmonic reduction, DC voltage regulation and power factor correction.

scholarly journals OPTIMIZE THE PERFORMANCE OF ELECTRICAL EQUIPMENT IN GAS SEPARATION STATIONS (DEGASSING STATION DS ) AND ELECTRICAL SUBMERSIBLE PUMPS OF OIL EQUIPMENT FOR OIL RUMAILA FIELD

2019 ◽  
Vol 21 (1-2) ◽  
pp. 141-145 ◽  
Author(s):  
Majid Abdulhameed Abdulhy Al-Ali ◽  
V. Yu. Kornilov ◽  
A. G. Gorodnov
Keyword(s):  
Power Factor ◽  
Reactive Power ◽  
Low Voltage ◽  
Voltage Drop ◽  
Reducing Power ◽  
Electrical Equipment ◽  
Voltage Regulation ◽  
Total Power ◽  
Electrical Submersible Pumps ◽  
Energy Compensation

Annotation: There are various types of electrical equipment used in the extraction of oil at the Rumaila field, with an average voltage of 11 kV and a low voltage of 0.4 kV. The most common elements in this class are transformers and reactors, engines and gas discharge lamps. All of this equipment consumes reactive power and reduces the value of the power factor. (Power factor is the ratio of kW to kVA). The closer the power factor to the maximum possible value of 1, the greater the benefit for the consumer and supplier. In case of low power factor, the current will be increased, and this high current will lead to (large line losses, an increase in the nominal total power of kVA and overhaul dimensions of electrical equipment, deterioration in voltage regulation process and an increase in voltage drop, a decrease in efficiency).Power factor improvement allows the use of smaller transformers, switchgear and cables, etc. as well as reducing power losses and voltage drop in an installation. Improving the power factor of an installation requires a bank of capacitors which acts as a source of reactive energy. These arrangements provide reactive energy compensation. In Rumila, An improvement of the power factor of an installation presents several technical and economic advantages, notably in the reduction of electricity bills, we save (685.854.007 Iraqi Dinar= 550.000 $) for one month . All this work takes 6 to 12 month.

scholarly journals Voltage Sag, Voltage Swell and Harmonics Reduction Using Unified Power Quality Conditioner (UPQC) Under Nonlinear Loads

2021 ◽  
Vol 17 (2) ◽  
pp. 140-150
Author(s):  
Ahmed Qasim ◽  
Fadhil Tahir ◽  
Ahmed Alsammak
Keyword(s):  
Power Quality ◽  
Power Distribution ◽  
Reactive Power ◽  
Supply Voltage ◽  
Harmonic Distortion ◽  
Distribution Networks ◽  
Unit Vector ◽  
Voltage Sag ◽  
Nonlinear Loads ◽  
Voltage Swell

In light of the widespread usage of power electronics devices, power quality (PQ) has become an increasingly essential factor. Due to nonlinear characteristics, the power electronic devices produce harmonics and consume lag current from the utility. The UPQC is a device that compensates for harmonics and reactive power while also reducing problems related to voltage and current. In this work, a three-phase, three-wire UPQC is suggested to reduce voltage-sag, voltage-swell, voltage and current harmonics. The UPQC is composed of shunt and series Active Power Filters (APFs) that are controlled utilizing the Unit Vector Template Generation (UVTG) technique. Under nonlinear loads, the suggested UPQC system can be improved PQ at the point of common coupling (PCC) in power distribution networks. The simulation results show that UPQC reduces the effect of supply voltage changes and harmonic currents on the power line under nonlinear loads, where the Total Harmonic Distortion (THD) of load voltages and source currents obtained are less than 5%, according to the IEEE-519 standard.

scholarly journals Classification of Voltage Sag Propagation under Double Line to Ground Fault on a Low Voltage Distribution Power Network

2021 ◽  
Vol 11 (2) ◽  
pp. 6949-6955
Author(s):  
A. K. Junejo ◽  
M. A. Koondhar ◽  
M. A. Memon ◽  
I. A. Channa ◽  
S. A. A. S. Bukhari
Keyword(s):  
Power Quality ◽  
Low Voltage ◽  
Voltage Drop ◽  
Voltage Sag ◽  
Power Network ◽  
Voltage Transformer ◽  
Double Line ◽  
Ground Fault ◽  
Zero Sequence ◽  
Distribution Power Network

The key issue of the voltage-sag propagation on the different types of winding connections for the low voltage transformer in the distribution power network is considered in this study. The issues of voltage sag propagation depend upon the type of asymmetrical fault and the connection of the transformer windings. In this paper, the double line to ground fault is adopted for the voltage sag characterization. The depiction of the sage propagation is an outcome of the zero sequence components. Voltage sag propagation detection can be used to improve the power quality of the system. The obtained results reveal the characteristics of the voltage drop propagation from the primary to the secondary winding of the transformer throughout different connection. The implemented method will help analyze the Power Quality (PQ) problem in terms of voltage sag of the distributed transmission networks of the power system.

scholarly journals On the Efficiency in Electrical Networks with AC and DC Operation Technologies: A Comparative Study at the Distribution Stage

Electronics ◽  
2020 ◽  
Vol 9 (9) ◽  
pp. 1352 ◽  
Author(s):  
Oscar Danilo Montoya ◽  
Federico Martin Serra ◽  
Cristian Hernan De Angelo
Keyword(s):  
Power Distribution ◽  
Urban Areas ◽  
Optimal Power Flow ◽  
Low Voltage ◽  
Mathematical Formulation ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Numerical Results ◽  
Energy Losses ◽  
Electrical Networks

This research deals with the efficiency comparison between AC and DC distribution networks that can provide electricity to rural and urban areas from the point of view of grid energy losses and greenhouse gas emissions impact. Configurations for medium- and low-voltage networks are analyzed via optimal power flow analysis by adding voltage regulation and devices capabilities sources in the mathematical formulation. Renewable energy resources such as wind and photovoltaic are considered using typical daily generation curves. Batteries are formulated with a linear representation taking into account operative bounds suggested by manufacturers. Numerical results in two electrical networks with 0.24 kV and 12.66 kV (with radial and meshed configurations) are performed with constant power loads at all the nodes. These simulations confirm that power distribution with DC technology is more efficient regarding energy losses, voltage profiles and greenhouse emissions than its AC counterpart. All the numerical results are tested in the General Algebraic Modeling System widely known as GAMS.

scholarly journals Using Energy Storage Inverters of Prosumer Installations for Voltage Control in Low-Voltage Distribution Networks

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1121
Author(s):  
Rozmysław Mieński ◽  
Przemysław Urbanek ◽  
Irena Wasiak
Keyword(s):  
Energy Storage ◽  
Control Strategy ◽  
Reactive Power ◽  
Low Voltage ◽  
Storage System ◽  
Distribution Networks ◽  
Energy Storage System ◽  
Voltage Regulation ◽  
Active Power ◽  
Total Power

The paper includes the analysis of the operation of low-voltage prosumer installation consisting of receivers and electricity sources and equipped with a 3-phase energy storage system. The aim of the storage application is the management of active power within the installation to decrease the total power exchanged with the supplying network and thus reduce energy costs borne by the prosumer. A solution for the effective implementation of the storage system is presented. Apart from the active power management performed according to the prosumer’s needs, the storage inverter provides the ancillary service of voltage regulation in the network according to the requirements of the network operator. A control strategy involving algorithms for voltage regulation without prejudice to the prosumer’s interest is described in the paper. Reactive power is used first as a control signal and if the required voltage effect cannot be reached, then the active power in the controlled phase is additionally changed and the Energy Storage System (ESS) loading is redistributed in phases in such a way that the total active power set by the prosumer program remains unchanged. The efficiency of the control strategy was tested by means of a simulation model in the PSCAD/EMTDC program. The results of the simulations are presented.

scholarly journals Voltage Rise Regulation with a Grid Connected Solar Photovoltaic System

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7510
Author(s):  
Akinyemi Ayodeji Stephen ◽  
Kabeya Musasa ◽  
Innocent Ewean Davidson
Keyword(s):  
Power Quality ◽  
Power Factor ◽  
Reactive Power ◽  
Voltage Regulation ◽  
Photovoltaic System ◽  
Voltage Amplitude ◽  
Phase Voltage ◽  
Unity Power Factor ◽  
Voltage Rise ◽  
Grid Current

Renewable Distributed Generation (RDG), when connected to a Distribution Network (DN), suffers from power quality issues because of the distorted currents drawn from the loads connected to the network over generation of active power injection at the Point of Common Coupling (PCC). This research paper presents the voltage rise regulation strategy at the PCC to enhance power quality and continuous operation of RDG, such as Photovoltaic Arrays (PVAs) connected to a DN. If the PCC voltage is not regulated, the penetration levels of the renewable energy integration to a DN will be limited or may be ultimately disconnected in the case of a voltage rise issue. The network is maintained in both unity power factor and voltage regulation mode, depending on the condition of the voltage fluctuation occurrences at the PCC. The research investigation shows that variation in the consumer’s loads (reduction) causes an increase in the power generated from the PVA, resulting in an increase in the grid current amplitude, reduction in the voltage of the feeder impedance and an increase in the phase voltage amplitude at the PCC. When the system is undergoing unity power factor mode, PCC voltage amplitude tends to rises with the loads. Its phase voltage amplitude rises above an acceptable range with no-loads which are not in agreement, as specified in the IEEE-1547 and Southern Africa grid code prerequisite. Incremental Conduction with Integral Regulator bases (IC + PI) are employed to access and regulate PVA generation, while the unwanted grid current distortions are attenuated from the network using an in-loop second order integral filtering circuit algorithm. Hence, the voltage rise at the PCC is mitigated through the generation of positive reactive power to the grid from the Distribution Static Compensator (DSTATCOM), thereby regulating the phase voltage. The simulation study is carried out in a MATLAB/Simulink environment for PVA performance.

scholarly journals Rancang Bangun Pengaman Panel Distribusi Tenaga Listrik Di Lippo Plaza Sidoarjo Dari Kebakaran Berbasis Arduino Nano

2017 ◽  
Vol 1 (2) ◽  
pp. 31
Author(s):  
Achmad Solih ◽  
Jamaaluddin Jamaaluddin
Keyword(s):  
Control System ◽  
Power Factor ◽  
Power Distribution ◽  
Low Voltage ◽  
Capacitor Bank ◽  
Warning Sign ◽  
Inductive Load ◽  
Three Phase ◽  
Working Principle ◽  
Power Distribution Control

Panel system power distribution at Lippo Plaza Mall Sidoarjo consists of several parts, namely from Cubicle 20 KV, 20 KV step-down transformer for 380 V, then the supply to LVMDP (Low Voltage Main Distribution Panel) The new panel to the user. Before delivery to users to note that the power factor is corrected using a capacitor bank. Less good a power factor is turned into inductive load on the capacitor bank so that temperatures high  because of high load resulting capacitor bank erupt. To overcome in this study proposes a safety panel automation power distribution control system using a microcontroller. Control system microcontrollers for safety panel power distribution consists of: Microcontroller (Arduino Nano), Light sensor (LDR), temperature sensor (LM35DZ), LCD 16x2 I2C, Actuators (fan, buzzer, relay switch breaker network three phase), switch ( relay 5 VDC), ADC as Input data. The working principle of this microcontroller LM35DZ if the sensor detects a high temperature fan will flash, if the LDR sensor detects sparks then the buzzer will sound as a warning sign of the dangers and disconnected the electricity network. From the design of a safety tool for power distribution panels due to high temperatures or sparks as well as the expected rate of fire outbreaks can be prevented.

scholarly journals Rancang Bangun Alat Deteksi Stabilitas Tegangan Jangka Panjang Pada Jaringan Distribusi Tegangan Rendah

Electrician ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 33
Author(s):  
Osea Zebua ◽  
Noer Soedjarwanto ◽  
Jemi Anggara
Keyword(s):  
Power Distribution ◽  
Voltage Stability ◽  
Low Voltage ◽  
Distribution Network ◽  
Distribution Networks ◽  
Current Data ◽  
Voltage Distribution ◽  
Power Distribution Networks ◽  
Long Time

Intisari — Stabilitas tegangan telah menjadi perhatian yang penting dalam operasi jaringan distribusi tenaga listrik. Ketidakstabilan tegangan dapat menyebabkan kerusakan pada peralatan-peralatan listrik bila terjadi dalam waktu yang lama. Makalah ini bertujuan untuk merancang dan membuat peralatan deteksi stabilitas tegangan jangka panjang pada jaringan tegangan rendah. Sensor tegangan dan sensor arus digunakan untuk memperoleh data tegangan dan arus. Mikrokontroler Arduino digunakan untuk memproses perhitungan deteksi stabilitas tegangan jangka panjang dari data tegangan yang diperoleh dari sensor. Hasil deteksi kondisi stabilitas tegangan ditampilkan dengan indikator lampu led. Hasil pengujian pada jaringan distribusi tegangan rendah tiga fasa menunjukkan bahwa peralatan dapat mendeteksi gangguan stabilitas tegangan jangka panjang secara online dan dinamis.Kata kunci — Deteksi, stabilitas tegangan jangka panjang, jaringan distribusi tegangan rendah. Abstract — Voltage stability has become important concern in the operation of electric power distribution networks. Voltage instability can cause damage to electrical equipments if it occurs for a long time. This paper aims to design and build long-term voltage stability detection equipment on low-voltage network. Voltage sensors and current sensors are used to obtain voltage and current data. The Arduino microcontroller is used to process calculation of long-term voltage stability detection from data obtained from the sensors. The results of detection of voltage stability conditions are displayed with the LED indicators. Test result on three-phase low-voltage distribution network shows that equipment can detect long–term voltage stability disturbance online and dynamically.Keywords— Detection, long-term voltage stability, low-voltage distribution network.

Sign in / Sign up

Export Citation Format

Share Document