Uncertainty in limb aerosol measurements following the Raikoke eruption

Author(s):  
Landon Rieger ◽  
Adam Bourassa ◽  
Daniel Zawada ◽  
Doug Degenstein ◽  
Sergey Khaykin ◽  
...  

<p>The eruption of Raikoke on June 22nd, 2019 was one of the largest in recent decades, spewing approximately 1.5 Tg of sulfur up to 17 km altitude. This eruption has been widely studied using a combination of climate models and measurement systems, including ground based lidars, in situ particle counters, and a variety of satellite platforms. The early plume has been well categorized by high-resolution measurements from CALIPSO, MODIS, VIIRS, IASI and other nadir viewing instruments, but as the plume ages investigation often shifts to limb sounding instruments that provide greater sensitivity to lower aerosol levels. These instruments have proven critical in understanding the long-term radiative and climatic impacts of stratospheric aerosol burdens after these explosive events, but the complexity of the measurements, sampling, and retrievals has made error characterization in high-loading conditions difficult.</p><p>This work explores systematic biases in limb measurements after the Raikoke eruption due to a variety of factors often implicit in the retrievals and analysis. Near-coincident CALIPSO, SAGE III and OMPS-LP measurements are used to investigate saturation of limb-sounding measurement in the early plume. The recent OMPS-LP v2 stratospheric aerosol product is compared with the University of Saskatchewan product to investigate benefits and drawbacks of the tomographic approach. SAGE III measurements are used as a validation when available although coverage limitations preclude comparisons in the thickest parts of the plume.  This work highlights the subtleties in comparing limb observations, with implications for model comparisons after large events such as volcanic eruptions and forest fires. Not only in the early plume, where sampling can be sparse, but also in the weeks and months following the eruption.</p>

2021 ◽  
Author(s):  
Michael P. Cartwright ◽  
Jeremy J. Harrison ◽  
David P. Moore

<p>Carbonyl sulfide (OCS) is the most abundant sulfur containing gas in the atmosphere and is an important source of stratospheric aerosol. Furthermore, it has been shown that OCS can be used as a proxy for photosynthesis, which is a powerful tool in quantifying global gross primary production. While considerable improvements have been made in our understanding of the location and magnitude of OCS fluxes over the past few decades, recent studies highlight the need for a new satellite dataset to help reduce the uncertainties in current estimations. The Infrared Atmospheric Sounding Interferometer (IASI) instruments on-board the MetOp satellites offer over 14 years of nadir viewing radiance measurements with excellent spatial coverage. Given that there are currently three IASI instruments in operation, there is the potential for a significantly larger OCS dataset than is currently available elsewhere. Retrievals of OCS from these IASI radiances have been made using an adapted version of the University of Leicester IASI Retrieval Scheme (ULIRS). OCS total column amounts are calculated from profiles retrieved on a 31-layer equidistant pressure grid, using an optimal estimation approach for microwindows in the range 2000 – 2100 cm<sup>-1</sup> wavenumbers. Sensitivity of the measurements peak in the mid-troposphere, between 5 – 10 km.</p><p>The outlook of this work is to produce a long-term OCS satellite observational data set that provides fresh insight to the spatial distribution and trend of atmospheric OCS. Here, we present subsets of data in the form of case studies for different geographic regions and time periods.</p>


2016 ◽  
Author(s):  
Davide Zanchettin ◽  
Myriam Khodri ◽  
Claudia Timmreck ◽  
Matthew Toohey ◽  
Anja Schmidt ◽  
...  

Abstract. The enhancement of the stratospheric aerosol layer by volcanic eruptions induces a complex set of responses causing global and regional climate effects on a broad range of timescales. Uncertainties exist regarding the climatic response to strong volcanic forcing identified in coupled climate simulations that contributed to the fifth phase of the Climate Model Intercomparison Project (CMIP5). In order to better understand the sources of these model diversities, the model intercomparison project on the climate response to volcanic forcing (VolMIP) has defined a coordinated set of idealized volcanic perturbation experiments to be carried out in alignment with the CMIP6 protocol. VolMIP provides a common stratospheric aerosol dataset for each experiment to eliminate differences in the applied volcanic forcing, and defines a set of initial conditions to determine how internal climate variability contributes to determining the response. VolMIP will assess to what extent volcanically-forced responses of the coupled ocean-atmosphere system are robustly simulated by state-of-the-art coupled climate models and identify the causes that limit robust simulated behavior, especially differences in the treatment of physical processes. This paper illustrates the design of the idealized volcanic perturbation experiments in the VolMIP protocol and describes the common aerosol forcing input datasets to be used.


2018 ◽  
Vol 18 (15) ◽  
pp. 11149-11169 ◽  
Author(s):  
Johan Friberg ◽  
Bengt G. Martinsson ◽  
Sandra M. Andersson ◽  
Oscar S. Sandvik

Abstract. We present a study on the stratospheric aerosol load during 2006–2015, discuss the influence from volcanism and other sources, and reconstruct an aerosol optical depth (AOD) data set in a resolution of 1∘ latitudinally and 8 days timewise. The purpose is to include the “entire” stratosphere, from the tropopause to the almost particle-free altitudes of the midstratosphere. A dynamic tropopause of 1.5 PVU was used, since it enclosed almost all of the volcanic signals in the CALIOP data set. The data were successfully cleaned from polar stratospheric clouds using a temperature threshold of 195 K. Furthermore, a method was developed to correct data when the CALIOP laser beam was strongly attenuated by volcanic aerosol, preventing a negative bias in the AOD data set. Tropospheric influence, likely from upwelling dust, was found in the extratropical transition layer in spring. Eruptions of both extratropical and tropical volcanoes that injected aerosol into the stratosphere impacted the stratospheric aerosol load for up to a year if their clouds reached lower than 20 km altitude. Deeper-reaching tropical injections rose in the tropical pipe and impacted it for several years. Our AODs mostly compare well to other long-term studies of the stratospheric AOD. Over the years 2006–2015, volcanic eruptions increased the stratospheric AOD on average by ∼40 %. In absolute numbers the stratospheric AOD and radiative forcing amounted to 0.008 and −0.2 W m−2, respectively.


2021 ◽  
Vol 21 (2) ◽  
pp. 1143-1158 ◽  
Author(s):  
Larry W. Thomason ◽  
Mahesh Kovilakam ◽  
Anja Schmidt ◽  
Christian von Savigny ◽  
Travis Knepp ◽  
...  

Abstract. An analysis of multiwavelength stratospheric aerosol extinction coefficient data from the Stratospheric Aerosol and Gas Experiment II and III/ISS instruments is used to demonstrate a coherent relationship between the perturbation in extinction coefficient in an eruption's main aerosol layer and the wavelength dependence of that perturbation. This relationship spans multiple orders of magnitude in the aerosol extinction coefficient of stratospheric impact of volcanic events. The relationship is measurement-based and does not rely on assumptions about the aerosol size distribution. We note limitations on this analysis including that the presence of significant amounts of ash in the main sulfuric acid aerosol layer and other factors may significantly modulate these results. Despite these limitations, the findings suggest an avenue for improving aerosol extinction coefficient measurements from single-channel observations such as the Optical Spectrograph and Infrared Imager System as they rely on a prior assumptions about particle size. They may also represent a distinct avenue for the comparison of observations with interactive aerosol models used in global climate models and Earth system models.


2020 ◽  
Author(s):  
Masatomo Fujiwara ◽  
Tetsu Sakai ◽  
Koichi Shiraishi ◽  
Yoichi Inai ◽  
Sergey Khaykin ◽  
...  

Abstract. Eastward airmass transport from the Asian summer monsoon (ASM) anticyclone in the upper troposphere and lower stratosphere (UTLS) often involves eastward shedding vortices, which can cover most of the Japanese archipelago. We investigated the aerosol characteristics of these vortices by analysing data from two lidar systems in Japan, at Tsukuba (36.1° N, 140.1° E) and Fukuoka (33.55° N, 130.36° E), during the summer of 2018. We observed several events with enhanced particle signals at Tsukuba at 15.5–18 km altitude (at or above the local tropopause) during August–September 2018, with a backscattering ratio of ~1.10 and particle depolarization of ~5 % (i.e., not spherical, but more spherical than ice crystals). These particle characteristics may be consistent with those of solid aerosol particles, such as ammonium nitrate. Each event had a timescale of a few days. During the same study period, we also observed similar enhanced particle signals in the lower stratosphere at Fukuoka. The upper troposphere is often covered by cirrus clouds at both lidar sites. Backward trajectory calculations for these sites for days with enhanced particle signals in the lower stratosphere and days without indicate that the former airmasses originated within the ASM anticyclone, and the latter more from edge regions. Reanalysis carbon-monoxide and satellite water-vapour data indicate that eastward shedding vortices were involved in the observed aerosol enhancements. Satellite aerosol data confirm that the period and latitudinal region were free from the direct influence of documented volcanic eruptions and high latitude forest fires. Our results indicate that the Asian Tropopause Aerosol Layer (ATAL) over the ASM region extends east towards Japan in association with the eastward shedding vortices, and that lidar systems in Japan can detect at least the lower stratospheric portion of the ATAL during periods when the lower stratosphere is undisturbed by volcanic eruptions and forest fires. The upper tropospheric portion of the ATAL is either depleted by tropospheric processes (convection and wet scavenging) during eastward transport or is obscured by much stronger cirrus cloud signals.


2021 ◽  
Vol 21 (4) ◽  
pp. 3073-3090
Author(s):  
Masatomo Fujiwara ◽  
Tetsu Sakai ◽  
Tomohiro Nagai ◽  
Koichi Shiraishi ◽  
Yoichi Inai ◽  
...  

Abstract. Eastward air-mass transport from the Asian summer monsoon (ASM) anticyclone in the upper troposphere and lower stratosphere (UTLS) often involves eastward-shedding vortices, which can cover most of the Japanese archipelago. We investigated the aerosol characteristics of these vortices by analysing data from two lidar systems in Japan, at Tsukuba (36.1∘ N, 140.1∘ E) and Fukuoka (33.55∘ N, 130.36∘ E), during the summer of 2018. We observed several events with enhanced particle signals at Tsukuba at 15.5–18 km of altitude (at or above the local tropopause) during August–September 2018, with a backscattering ratio of ∼ 1.10 and particle depolarization of ∼ 5 % (i.e. not spherical, but more spherical than ice crystals). These particle characteristics may be consistent with those of solid aerosol particles, such as ammonium nitrate. Each event had a timescale of a few days. During the same study period, we also observed similar enhanced particle signals in the lower stratosphere at Fukuoka. The upper troposphere is often covered by cirrus clouds at both lidar sites. Backward trajectory calculations for these sites for days with enhanced particle signals in the lower stratosphere and days without indicate that the former air masses originated within the ASM anticyclone and the latter more from edge regions. Reanalysis carbon monoxide and satellite water vapour data indicate that eastward-shedding vortices were involved in the observed aerosol enhancements. Satellite aerosol data confirm that the period and latitudinal region were free from the direct influence of documented volcanic eruptions and high-latitude forest fires. Our results indicate that the Asian tropopause aerosol layer (ATAL) over the ASM region extends east towards Japan in association with the eastward-shedding vortices and that lidar systems in Japan can detect at least the lower-stratospheric portion of the ATAL during periods when the lower stratosphere is undisturbed by volcanic eruptions and forest fires. The upper-tropospheric portion of the ATAL is either depleted by tropospheric processes (convection and wet scavenging) during eastward transport or is obscured by much stronger cirrus cloud signals.


2021 ◽  
Author(s):  
Thomas Aubry ◽  
Anja Schmidt ◽  
Alix Harrow ◽  
Jeremy Walton ◽  
Jane Mulcahy ◽  
...  

<p>Reconstructions of volcanic aerosol forcing and its climatic impacts are undermined by uncertainties in both the models used to build these reconstructions as well as the proxy and observational records used to constrain those models. Reducing these uncertainties has been a priority and in particular, several modelling groups have developed interactive stratospheric aerosol models. Provided with an initial volcanic injection of sulfur dioxide, these models can interactively simulate the life cycle and optical properties of sulfate aerosols, and their effects on climate. In contrast, most climate models that took part in the Coupled Model Intercomparison Project Phase 5 and 6 (CMIP6) directly prescribe perturbations in atmospheric optical properties associated with an eruption. However, before the satellite era, the volcanic forcing dataset used for CMIP6 mostly relies on a relatively simple aerosol model and a volcanic sulfur inventory derived from ice-cores, both of which have substantial associated uncertainties.</p><p>In this study, we produced a new set of historical simulations using the UK Earth System Model UKESM1, with interactive stratospheric aerosol capability (referred to as interactive runs hereafter) instead of directly prescribing the CMIP6 volcanic forcing dataset as was done for CMIP6 (standard runs, hereafter). We used one of the most recent volcanic sulfur inventories as input for the interactive runs, in which aerosol properties are consistent with the model chemistry, microphysics and atmospheric components. We analyzed how the stratospheric aerosol optical depth, the radiative forcing and the climate response to volcanic eruptions differed between interactive and standard runs, and how these compare to observations and proxy records. In particular, we investigate in detail the differences in the response to the large-magnitude Krakatoa 1883 eruption between the two sets of runs. We also discuss differences for the 1979-2015 period where the forcing data in standard runs is directly constrained from satellite observations. Our results shed new light on uncertainties affecting the reconstruction of past volcanic forcing and highlight some of the benefits and disadvantages of using interactive stratospheric aerosol capabilities instead of a unique prescribed volcanic forcing dataset in CMIP’s historical runs.</p>


2020 ◽  
Author(s):  
Sergey Khaykin ◽  
Sophie Godin-Beekmann ◽  
Ghassan Taha ◽  
Artem Feofilov ◽  
Adam Bourassa ◽  
...  

<p>    During the last 2 years (2018-2019) a series of volcanic eruptions led to remarkable enhancements in stratospheric aerosol load. These are eruptions of <strong>Ambae</strong> (July 2018, Vanuatu), <strong>Raikoke</strong> (June 2019, Russia) and <strong>Ulawun</strong> (July 2019, Papua New Guinea). In this study we examine the evolution of the stratospheric aerosol bulk optical properties following these events in consideration of large-scale stratospheric circulation. We use long-term aerosol records by <strong>ground-based lidars</strong> in both hemispheres together with global observations by various satellite missions (<strong>OMPS-LP, SAGE III, OSIRIS, CALIOP</strong>) and discuss the consistency between these datasets.  In addition, we evaluate the preliminary lower stratosphere aerosol product by ESA <strong>Aeolus</strong> mission through intercomparison with ground-based lidars.</p><p>   The 28-yr Observatoire de Haute Provence (<strong>OHP) lidar record</strong> shows that<strong> Raikoke eruption has led to the strongest enhancement of stratospheric aerosol optical depth (SAOD) in the northern extratropics since Pinatubo eruption</strong>. Satellite observations suggest that the stratospheric plume of Raikoke has dispersed throughout the entire Northern hemisphere and ascended up to 27 km altitude. The eruption of Ulawun in the tropics has further boosted the stratospheric aerosol load and by Fall 2019, the <strong>global mean SAOD was a factor of 2.5 higher than its background level</strong>.</p><p>    At the turn of the year 2020, while both Raikoke and Ulawun aerosols were still present in the stratosphere, a dramatic bushfire event accompanied by vigorous fire-induced thunderstorms (PyroCb) in eastern Australia caused a massive injection of smoke into the stratosphere. The early detections of stratospheric smoke by OMPS-LP suggest that the zonal-mean SAOD perturbation caused by this event<strong> exceeds the previous record-breaking PyroCb-related perturbation</strong> after the British Columbia fires in August 2017. We use satellite observations of aerosol and trace gases (H2O, CO) to characterize the stratospheric impact of the wildfires and contrast it with that of volcanic eruptions.</p>


2017 ◽  
Vol 17 (4) ◽  
pp. 3067-3081 ◽  
Author(s):  
Vladimir V. Zuev ◽  
Vladimir D. Burlakov ◽  
Aleksei V. Nevzorov ◽  
Vladimir L. Pravdin ◽  
Ekaterina S. Savelieva ◽  
...  

Abstract. There are only four lidar stations in the world which have almost continuously performed observations of the stratospheric aerosol layer (SAL) state over the last 30 years. The longest time series of the SAL lidar measurements have been accumulated at the Mauna Loa Observatory (Hawaii) since 1973, the NASA Langley Research Center (Hampton, Virginia) since 1974, and Garmisch-Partenkirchen (Germany) since 1976. The fourth lidar station we present started to perform routine observations of the SAL parameters in Tomsk (56.48° N, 85.05° E, Western Siberia, Russia) in 1986. In this paper, we mainly focus on and discuss the stratospheric background period from 2000 to 2005 and the causes of the SAL perturbations over Tomsk in the 2006–2015 period. During the last decade, volcanic aerosol plumes from tropical Mt. Manam, Soufrière Hills, Rabaul, Merapi, Nabro, and Kelut and extratropical (northern) Mt. Okmok, Kasatochi, Redoubt, Sarychev Peak, Eyjafjallajökull, and Grímsvötn were detected in the stratosphere over Tomsk. When it was possible, we used the NOAA HYSPLIT trajectory model to assign aerosol layers observed over Tomsk to the corresponding volcanic eruptions. The trajectory analysis highlighted some surprising results. For example, in the cases of the Okmok, Kasatochi, and Eyjafjallajökull eruptions, the HYSPLIT air mass backward trajectories, started from altitudes of aerosol layers detected over Tomsk with a lidar, passed over these volcanoes on their eruption days at altitudes higher than the maximum plume altitudes given by the Smithsonian Institution Global Volcanism Program. An explanation of these facts is suggested. The role of both tropical and northern volcanic eruptions in volcanogenic aerosol loading of the midlatitude stratosphere is also discussed. In addition to volcanoes, we considered other possible causes of the SAL perturbations over Tomsk, i.e., the polar stratospheric cloud (PSC) events and smoke plumes from strong forest fires. At least two PSC events were detected in 1995 and 2007. We also make an assumption that the Kelut volcanic eruption (Indonesia, February 2014) could be the cause of the SAL perturbations over Tomsk during the first quarter of 2015.


2021 ◽  
Vol 14 (3) ◽  
pp. 1219-1236
Author(s):  
Qi Tang ◽  
Michael J. Prather ◽  
Juno Hsu ◽  
Daniel J. Ruiz ◽  
Philip J. Cameron-Smith ◽  
...  

Abstract. Stratospheric ozone affects climate directly as the predominant heat source in the stratosphere and indirectly through chemical reactions controlling other greenhouse gases. The U.S. Department of Energy's Energy Exascale Earth System Model version 1 (E3SMv1) implemented a new ozone chemistry module that improves the simulation of the sharp tropopause gradients, replacing a version based partly on long-term average climatologies that poorly represented heating rates in the lowermost stratosphere. The new O3v2 module extends seamlessly into the troposphere and preserves the naturally sharp cross-tropopause gradient, with 20 %–40 % less ozone in this region. Additionally, O3v2 enables the diagnosis of stratosphere–troposphere exchange flux of ozone, a key budget term lacking in E3SMv1. Here, we evaluate key features in ozone abundance and other closely related quantities in atmosphere-only E3SMv1 simulations driven by observed sea surface temperatures (SSTs, years 1990–2014), comparing them with satellite observations of ozone and also with the University of California, Irvine chemistry transport model (UCI CTM) using the same stratospheric chemistry scheme but driven by European Centre forecast fields for the same period. In terms of stratospheric column ozone, O3v2 shows reduced mean bias and improved northern midlatitude variability, but it is not quite as good as the UCI CTM. As expected, SST-forced E3SMv1 simulations cannot synchronize with observed quasi-biennial oscillations (QBOs), but they do show the typical QBO pattern seen in column ozone. This new O3v2 E3SMv1 model mostly retains the same climate state and climate sensitivity as the previous version, and we recommend its use for other climate models that still use ozone climatologies.


Sign in / Sign up

Export Citation Format

Share Document