SIGMA-DELTA PHASE LOCKING LOOP FOR GEOPHYSICAL RESEARCH

Author(s):  
Vadim Zhmud ◽  
Yury Fomin ◽  
Lubomir Dimitrov ◽  
Sergei Panov ◽  
Vladimir Semibalamut
Author(s):  
L. S. Lin ◽  
C. C. Law

Inconel 718, a precipitation hardenable nickel-base alloy, is a versatile high strength, weldable wrought alloy that is used in the gas turbine industry for components operated at temperatures up to about 1300°F. The nominal chemical composition is 0.6A1-0.9Ti-19.OCr-18.0Fe-3Mo-5.2(Cb + Ta)- 0.1C with the balance Ni (in weight percentage). The physical metallurgy of IN 718 has been the subject of a number of investigations and it is now established that hardening is due, primarily, to the formation of metastable, disc-shaped γ" an ordered body-centered tetragonal structure (DO2 2 type superlattice).


Author(s):  
T. M. Weatherby ◽  
P.H. Lenz

Crustaceans, as well as other arthropods, are covered with sensory setae and hairs, including mechanoand chemosensory sensillae with a ciliary origin. Calanoid copepods are small planktonic crustaceans forming a major link in marine food webs. In conjunction with behavioral and physiological studies of the antennae of calanoids, we undertook the ultrastructural characterization of sensory setae on the antennae of Pleuromamma xiphias.Distal mechanoreceptive setae exhibit exceptional behavioral and physiological performance characteristics: high sensitivity (<10 nm displacements), fast reaction times (<1 msec latency) and phase locking to high frequencies (1-2 kHz). Unusual structural features of the mechanoreceptors are likely to be related to their physiological sensitivity. These features include a large number (up to 3000) of microtubules in each sensory cell dendrite, arising from or anchored to electron dense rods associated with the ciliary basal body microtubule doublets. The microtubules are arranged in a regular array, with bridges between and within rows. These bundles of microtubules extend far into each mechanoreceptive seta and terminate in a staggered fashion along the dendritic membrane, contacting a large membrane surface area and providing a large potential site of mechanotransduction.


Author(s):  
L. A. Giannuzzi ◽  
A. S. Ramani ◽  
P. R. Howell ◽  
H. W. Pickering ◽  
W. R. Bitler

The δ phase is a Zn-rich intermetallic, having a composition range of ∼ 86.5 - 92.0 atomic percent Zn, and is stable up to 665°C. The stoichiometry of the δ phase has been reported as FeZn7 and FeZn10 The deviation in stoichiometry can be attributed to variations in alloy composition used by each investigator. The structure of the δ phase, as determined by powder x-ray diffraction, is hexagonal (P63mc or P63/mmc) with cell dimensions a = 1.28 nm, c = 5.76 nm, and 555±8 atoms per unit cell. Later work suggested that the layer produced by hot-dip galvanizing should be considered as two distinct phases which are characterized by their morphological differences, namely: the iron-rich region with a compact appearance (δk) and the zinc-rich region with a columnar or palisade microstructure (δp). The sub-division of the δ phase was also based on differences in diffusion behavior, and a concentration discontinuity across the δp/δk boundary. However, work utilizing Weisenberg photographs on δ single crystals reported that the variation in lattice parameters with composition was small and hence, structurally, the δk phase and the δp phase were the same and should be thought of as a single phase, δ. Bastin et al. determined the average cell dimensions to be a = 1.28 nm and c = 5.71 nm, and suggested that perhaps some kind of ordering process, which would not be observed by x-ray diffraction, may be responsible for the morphological differences within the δ phase.


In automated control systems for technical processes, the conversion of a continuous signal into a digital code and vice versa from a digital code to a continuous (analog) value is widely used. For direct type converters often used the term ADC, the reverse - DAC. The characteristics of the converters often dramatically affect the parameters of the entire automated system. The importance of the correct choice of ADCs and DACs has especially increased recently in connection with the mass introduction of microcontrollers MC. Indeed, in addition to the ADC and DAC, it is necessary to place the processor core in the microcontroller's crystal, I/O interfaces and many other elements necessary for the functioning of the MC. The use of information converters in the construction industry imposes additional requirements on converters: for example, in building monitoring systems, precision ADCs with extremely high accuracy are often required (while performance may be low), in other applications it is necessary to provide the necessary parameters at a high level of industrial interference, etc. This article explores issues related to the rational choice of ADCs and DACs, taking into account current trends in the IT field and the specifics of work in the construction industry. Sigma-Delta converters are noted as the most promising models of direct type converters.


2009 ◽  
Vol E92-C (6) ◽  
pp. 860-863 ◽  
Author(s):  
Lukas FUJCIK ◽  
Linus MICHAELI ◽  
Jiri HAZE ◽  
Radimir VRBA

2019 ◽  
Vol 78 (13) ◽  
pp. 1167-1177
Author(s):  
S. K. Pidchenko ◽  
A. A. Taranchuk ◽  
A. Totsky ◽  
V. B. Sharonov

Sign in / Sign up

Export Citation Format

Share Document