Wireless Signal Propagation Prediction Based on Computer Vision Sensing Technology for Forestry Security Monitoring

In this paper, Computer Vision (CV) sensing technology based on Convolutional Neural Network (CNN) is introduced to process topographic maps for predicting wireless signal propagation models, which are applied in the field of forestry security monitoring. In this way, the terrain-related radio propagation characteristic including diffraction loss and shadow fading correlation distance can be predicted or extracted accurately and efficiently. Two data sets are generated for the two prediction tasks, respectively, and are used to train the CNN. To enhance the efficiency for the CNN to predict diffraction losses, multiple output values for different locations on the map are obtained in parallel by the CNN to greatly boost the calculation speed. The proposed scheme achieved a good performance in terms of prediction accuracy and efficiency. For the diffraction loss prediction task, 50% of the normalized prediction error was less than 0.518%, and 95% of the normalized prediction error was less than 8.238%. For the correlation distance extraction task, 50% of the normalized prediction error was less than 1.747%, and 95% of the normalized prediction error was less than 6.423%. Moreover, diffraction losses at 100 positions were predicted simultaneously in one run of CNN under the settings in this paper, for which the processing time of one map is about 6.28 ms, and the average processing time of one location point can be as low as 62.8 us. This paper shows that our proposed CV sensing technology is more efficient in processing geographic information in the target area. Combining a convolutional neural network to realize the close coupling of a prediction model and geographic information, it improves the efficiency and accuracy of prediction.

Realisation of Pressure Sensor using one Dimensional Indium Arsenide (InAs) Based Photonic Waveguide in 3 Communication Windows

Indium arsenide (InAs) based one dimensional photonic crystal waveguide is cautiously considered in three optical communication windows. Here, the emerging transmitted signal from one dimensional photonic structure is determined with the consideration of five types of losses (diffraction loss, reflection loss, absorption loss, propagation loss, polarisation loss). Further, the transmitted signal is obtained with respect to pressure, which ranges from 0 GPa to 5 GPa for different lattice constant of photonic structure (100 nm, 120 nm, 140 nm). Simulation upshots revealed that indium arsenide semiconductor based photonic waveguide shows an excellent outcome for pressure sensor in the three optical windows as well as different waveguide lengths.

Improvement of the Target Sensitivity in DECIGO by Optimizing Its Parameters for Quantum Noise Including the Effect of Diffraction Loss

The DECi-hertz Interferometer Gravitational-wave Observatory (DECIGO) is the future Japanese, outer space gravitational wave detector. We previously set the default design parameters to provide a good target sensitivity to detect the primordial gravitational waves (GWs). However, the updated upper limit of the primordial GWs by the Planck observations motivated us toward further optimization of the target sensitivity. Previously, we had not considered optical diffraction loss due to the very long cavity length. In this paper, we optimize various DECIGO parameters by maximizing the signal-to-noise ratio (SNR) of the primordial GWs to quantum noise, including the effects of diffraction loss. We evaluated the power spectrum density for one cluster in DECIGO utilizing the quantum noise of one differential Fabry–Perot interferometer. Then we calculated the SNR by correlating two clusters in the same position. We performed the optimization for two cases: the constant mirror-thickness case and the constant mirror-mass case. As a result, we obtained the SNR dependence on the mirror radius, which also determines various DECIGO parameters. This result is the first step toward optimizing the DECIGO design by considering the practical constraints on the mirror dimensions and implementing other noise sources.

Observation of terahertz coherent edge radiation amplified by infrared free-electron laser oscillations

A coupling device, which can extract coherent edge radiation (CER) from an optical cavity for a free-electron laser (FEL) without damaging the FEL due to diffraction loss, was developed at Nihon University. We successfully observed the CER beam with a power of 1 mW or more in the terahertz range during FEL oscillation. It is revealed that the CER power changed with the detuning of the optical cavity and the dependence of the CER power on the detuning length differs from that of the FEL power. The measured CER spectra indicate that the longitudinal electron distribution in a bunch is modulated by the FEL oscillation with a period corresponding to the FEL slippage length. We herein report the characteristics of the CER with FEL oscillation in detail. These results demonstrate that the CER is excellent tool to reveal the overall effect of FEL interaction on electron distribution in a bunch.

Quantum Noise in a Fabry-Perot Interferometer Including the Influence of Diffraction Loss of Light

The DECi-hertz Interferometer Gravitational wave Observatory (DECIGO) is designed to detect gravitational waves at frequencies between 0.1 and 10 Hz. In this frequency band, one of the most important science targets is the detection of primordial gravitational waves. DECIGO plans to use a space interferometer with optical cavities to increase its sensitivity. For evaluating its sensitivity, diffraction of the laser light has to be adequately considered. There are two kinds of diffraction loss: leakage loss outside the mirror and higher-order mode loss. These effects are treated differently inside and outside of the Fabry-Perot (FP) cavity. We estimated them under the conditions that the FP cavity has a relatively high finesse and the higher-order modes do not resonate. As a result, we found that the effects can be represented as a reduction of the effective finesse of the cavity with regard to quantum noise. This result is useful for optimization of the design of DECIGO. This method is also applicable to any FP cavities with a relatively small beam cut and the finesse sufficiently higher than 1.