Far Wake and Its Relation to Aerodynamic Efficiency

Correlations were found between the aerodynamic efficiency and the mean and fluctuating quantities in the far wake of a wall-to-wall SD7003 model and an AR 4 flat plate. This correlation was described algebraically by modeling the wake signature as a function of wing geometry and initial conditions. The model was benchmarked against experimental results to elicit the wing performance as a function of angle of attack by interrogating the wake. In these algebraic models, the drag coefficient along with other initial conditions of the turbulent generator (either airfoil or wing) were used to reconstruct the Reynolds Stress distribution and the momentum deficit distribution in the turbulent wake. Experiments were undertaken at the United States Air Force Research Labs Horizontal Free Surface Water Tunnel (AFRL/HFWT). These experiments build on previous results obtained at the University of Dayton Low Speed Wind Tunnel (UD-LSWT) on a cylinder, an AR 7 SD7062 wing, and a small remote control twin motor aircraft. The Reynolds stress and the momentum deficit of the turbulent generators were experimentally determined using Particle Image Velocimetry (PIV) with a minimum of 1000 image pairs averaged at each condition. The variation of an empirical factor (γ) used to match the Reynolds stress and momentum deficit distributions showed striking correlation to the variation of drag and aerodynamic efficiency of the turbulent generator. This correlation suggests that the wing performance information is preserved in the free shear layer 10 chord lengths downstream of the trailing edge (TE) of the wing irrespective of the dimensionality of the flow.

Aerodynamic Effect of the Gurney Flap on the Front Wing of a F1 Car and Flow Interactions with Car Components

The design of a racing car needs several aerodynamic design steps in order to achieve high performance. Each component has an aerodynamic interaction with the others and high performance requires a good match between them. The front wing is undoubtedly one of the main components to determine car performance with a strong interaction with the downstream components. The Gurney Flap (GF) is a small appendix perpendicular to the pressure side of the front wing at the trailing edge that can dramatically improve the front wing performance. In the literature, the performance of a GF on a single profile is well documented, while in this paper the GF mounted on the front wing of a racing car has been investigated and the interactions through the 3D flow structures are discussed. The global drag and downforce performance on the main components of the vehicle have been examined by comparing the cases with and without a GF. The GF increases the downforce by about 24% compared to a limited increase in the drag force. A fluid dynamic analysis has been carried out to understand the physical mechanisms of the flow interaction induced to the other components. The GF, in fact, enhances the ground effect, by redistributing the flow that interacts differently with the other components i.e., the wheel zone.

Fluid–structure interaction simulation on flight performance of a dragonfly wing under different pterostigma weights

The dragonfly wings provide insights for designing an efficient biomimetic micro air vehicle (BMAV). In this regard, this study focuses on investigating the effect of the pterostigma weight loading and its spatial location on the forewings of dragonfly by using the fluid–structure interaction simulation. This study also investigates the effect of change in the wing elasticity and density on the wing performance. The forewing, which mimics the real dragonfly wing, is flat with a 47.5 mm span and a 0.4 mm thickness. The wing was set to cruise at 3 m/s with a constant flapping motion at a frequency of 25 Hz. This study shows that a small increase of pterostigma loading (11% of wing weight) at the tip of the wing significantly improves the lift to drag ratio, CL/CD, which has 129.16% increment in comparison with no loading. The lift to drag ratio depends on the pterostigma location, pterostigma loading, elastic modulus and density. The results of this study can be used as a reference in future BMAV wing optimization design.

Investigation on the effect of leading edge tubercles of sweptback wing at low reynolds number

Aerodynamic efficiency of an airplane wing can be improved either by increasing its lift generation tendency or by reducing the drag. Recently, Bio-inspired designs have been received greater attention for the geometric modifications of airplane wings. One of the bio-inspired designs contains sinusoidal Humpback Whale (HW) tubercles, i.e., protuberances exist at the wing leading edge (LE). The tubercles have excellent flow control characteristics at low Reynolds numbers. The present work describes about the effect of tubercles on swept back wing performance at various Angle of Attack (AoA). NACA 0015 and NACA 4415 airfoils are used for swept back wing design with sweep angle about 30°. The modified wings (HUMP 0015 A, HUMP 0015 B, HUMP 4415 A, HUMP 4415 B) are designed with two amplitude to wavelength ratios (η) of 0.1 & 0.24 for the performance analysis. It is a novel effort to analyze the tubercle vortices along the span that induce additional flow energy especially, behind the tubercles peak and trough region. Subsequently, Co-efficient of Lift (CL), Co-efficient of Drag (CD) and boundary layer pressure gradients also predicted for modified and baseline (smooth LE) models in the pre & post-stall regimes. It was observed that the tubercles increase the performance of swept back wings by the enhanced CL/CD ratio in the pre-stall AoA region. Interestingly, the flow separation region behind the centerline of tubercles and formation of Laminar Separation Bubbles (LSB) were asymmetric because of the sweep.