Exploring the structural, optical and photoluminescent properties of (1-x)NiCo2O4/xPbS nanocomposites for optoelectronic applications

(1-x)NiCo2O4/xPbS (0≤x≤0.2) nanocomposite samples were synthesized using the hydrothermal and thermolysis procedures. The different phases developed in the obtained nanocomposite samples were accurately determined using the x-ray diffraction technique equipped with a line-detector. The percentage of the formed phases (NiCo2O4 (NCO), PbS, PbSO4), structural and microstructure parameters were determined using Rietveld quantitative phase analysis. The transmission electron microscope (TEM) images and Rietveld analysis reveal almost isotropic particle size in the nano range with a very narrow size distribution. The obtained phase percentages of PbS and PbSO4 are smaller than nominated values (x) suggesting dissolving of some Pb and S ions in NCO which then confirmed by the analysis of Fourier-transform infrared (FTIR) spectra of nanocomposite samples. The absorption spectra are modified upon doping NCO with PbS. The optical band gaps of the nanocomposites increase as the amount of PbS is increased. The effect of alloying on extinction coefficient, refractive index, dielectric constant, optical conductivity, the intensity, and emitted color from the photoluminescence of the nanocomposite samples are also studied. The refractive index values of NCO and NCO-PbS nanocomposite samples exhibit normal dispersions. The photoluminescent measurements reveal that NCO-PbS nanocomposites could emit a violet color. The improvement in the values of the non-linear optical (NLO) parameters of pristine NCO at high frequencies or the nanocomposite samples at low frequencies, nominated them to be used in NLO photonic applications.

Proposed method for scale drawing calculating depending on the line detector and length detector

A scale drawing is a significant tool in many fields such as geography, mathematics, and astronomy research as it has a variety of applications, including Google maps. A new way to benefit from the scale drawing in soccer image is presented in this paper. When the distance of the camera is uncertain, the scale drawing can be used to determine the relationship between the ball and players to estimate the ball size and determine the zooms in and out. The scale drawing and factor are used in architecture and image processing. After calculating the scale factor, the length of every part or line in the image can be computed by multiplying the original length by the scale factor. The research findings indicated that the proposed work was successful in computing the scale drawing in two ways, namely, line detector and length detector, with approximate results to the desired results

Application Of Ba0.5Sr0.5TiO3 (Bst) Film Doped With RuO2 (0%, 2%, 4% and 6%) On A Rice-Stalk Cutting Robot Model Based On A Line Follower With Hc-05 Bluetooth Control

Ba0.5Sr0.5TiO3 (BST) film doped with RuO2 with varying concentrations (0%, 2%, 4%, and 6%) on a p-type (100) silicon substrate has been successfully grown using the Chemical Solution Deposition (CSD) method and spin coating at a rotational speed of 3000 rpm for 30 seconds. The film on the substrate was then heated at 850 oC for 15 hours. BST film+RuO2 variations were characterized for their sensitivity as a light sensor. BST film+RuO2 variations were tested with a varied light source and reflective surface colors. Thin films have a range at the visible light wavelength, so LED lights were used as the light source in the present study. The light source selected was the blue LED because it had a high contrast in differentiating between dark and light-colored surfaces. Various electronic circuits assisted sensitivity characterization with the aim to produce a sensor that is highly sensitive to light. The response of BST film+ RuO2 variations differed according to the RuO2 doping concentration. BST film doped with RuO2 6% had a very good response to changes in light, so this film was applied as the line detector sensor in the line follower-based rice-stalk cutter model with an HC-05 Bluetooth control. Before being integrated with the microcontroller, the output voltage of the BST film was strengthened using an op-amp circuit so that the microcontroller could read the output voltage of the BST film.