Synthesis and Characterization of NaA Zeolite Using Natural Kaolinite Clays from Nigeria by Low Temperature Hydrothermal Method

Zeolites NaA is one of the most valuable synthetic zeolites widely used as ion-exchange material, catalysts, and adsorbents in industry. There is therefore need to adopt a more energy-efficient route for its synthesis from low-cost and sustainable raw materials. In this present work, zeolites Na-A was synthesized from natural kaolinite clays obtained from three selected regions (Ikere, Okpella and Kankara) in Nigeria. The as-received kaolinite clays (IKclay, OKclay and KAclay) were initially beneficiated thoroughly to obtain pure powders (˂75 μm). The processed kaolinite clay powders were then subjected to heating in a muffle furnace at 850oC for 3 h at a heating rate of 10oC/min to convert the kaolinite clays to their respective metakaolins. The obtained metakaolins were then reacted with NaOH solutions at varying concentrations of 3.0 and 4.0M respectively using a low temperature hydrothermal transformation to obtained Zeolites Na-A powders. The obtained zeolites were then analyzed by scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FT-IR). The results showed that zeolite NaA is produced with mixture of hydroxysodalite (HS) while the EDS revealed the presence of Si, Al, O and Na indicating chemical constituents of typical zeolite NaA. All the tested kaolinite clays are therefore suitable for preparation of zeolite NaA as cheaper source of silica and aluminum.

Synthesis of Zeolite A from Iraqi Natural Kaolin Using a Conventional Hydrothermal Synthesis Technique

The synthesis of zeolite materials by hydrothermal transformation of kaolin using a conventional hydrothermal method was investigated. Different analytical techniques were used to characterize the starting kaolin and produced zeolite A samples, including scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), x-ray diffraction (XRD), x-ray fluorescence (XRF), thermogravimetric analysis (TGA), and Fourier transform infrared (FT-IR) spectroscopy. The synthetic zeolite type A was obtained after activation of kaolin and metakaolin followed by different thermal and chemical treatments. The metakaolinization phase was achieved by calcining the kaolin in air at 600°C for 3 hours, a much lower temperature than previously reported in the literature. Metakaolin was treated with 3 M sodium hydroxide solution at a ratio of 1:5 and, using stainless steel autoclaves with teflon liners, heated the mixture to 200°C in a microwave for 24 hours. The results from this synthesis route showed that zeolite A with a cubic crystal habit has been successfully synthesized.

Fe/Ni Bimetallic Organic Framework Deposited on TiO2 Nanotube Array for Enhancing Higher and Stable Photoelectrochemical Activity of Oxygen Evaluation Reaction

Photoelectrochemical (PEC) water splitting is a promising strategy to improve the efficiency of oxygen evolution reactions (OERs). However, the efficient adsorption of visible light as well as long-term stability of light-harvesting electrocatalysis is the crucial issue in PEC cells. Metal–organic framework (MOF)-derived bimetallic electrocatalysis with its superior performance has wide application prospects in OER and PEC applications. Herein, we have fabricated a nickel and iron bimetallic organic framework (FeNi-MOF) deposited on top of anodized TiO2 nanotube arrays (TNTA) for PEC and OER applications. The FeNi-MOF/TNTA was incorporated through the electrochemical deposition of Ni2+ and Fe3+ onto the surface of TNTA and then connected with organic ligands by the hydrothermal transformation. Therefore, FeNi-MOF/TNTA demonstrates abundant photoelectrocatalytic active sites that can enhance the photocurrent up to 1.91 mA/cm2 under 100 mW/cm2 and a negligible loss in activity after 180 min of photoreaction. The FeNi-MOF-doped photoanode shows predominant photoelectrochemical performance due to the boosted excellent light-harvesting ability, rapid photoresponse, and stimulated interfacial energy of charge separation under the UV-visible light irradiation conditions. The results of this study give deep insight into MOF-derived bimetallic nanomaterial synthesis for photoelectrochemical OER and provide guidance on future electrocatalysis design.

Self-supported CdSe nanowire/nanosheet photoanodes on cadmium foil via in situ hydrothermal transformation of CdSe(en)0.5 complex nanostructures

Self-supported Cd(OH)2/CdSe NS photoanodes prepared via in situ hydrothermal transformation approach display 7.6 times higher photocurrent than that of CdSe(en)0.5. The role of Cd(OH)2 during PEC transformation is extensively proposed.

Cuttlefish Bone-Derived Biphasic Calcium Phosphate Scaffolds Coated with Sol-Gel Derived Bioactive Glass

The combination of calcium phosphates with bioactive glasses (BG) has received an increased interest in the field of bone tissue engineering. In the present work, biphasic calcium phosphates (BCP) obtained by hydrothermal transformation of cuttlefish bone (CB) were coated with a Sr-, Mg- and Zn-doped sol-gel derived BG. The scaffolds were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy. The initial CB structure was maintained after hydrothermal transformation (HT) and the scaffold functionalization did not jeopardize the internal structure. The results of the in-vitro bioactivity after immersing the BG coated scaffolds in simulated body fluid (SBF) for 15 days showed the formation of apatite on the surface of the scaffolds. Overall, the functionalized CB derived BCP scaffolds revealed promising properties, but further assessment of the in-vitro biological properties is needed before being considered for their use in bone tissue engineering applications.