Alkali-Silica. Reaction Of Foamed. Concrete Containing. Waste Glass as Aggregate

This research focused on examining Alkali-Silica. Reaction (ASR) of foamed concrete mixes containing1different1types of1crushed waste glass (CWG) with different chemical compositions. The reactivity was determined in sodium hydroxide solution by adopting mortar bar test. Four types of waste glass with different particle sizes and different percentages content were used. From the test results of recorded expansion of these mixes, it was noticed that the coarse glass resulted in more expansion than that of fine glass. Lead-silicate1glass (CR) exhibits the maximum expansion followed by1soda-lime1glass (SL) and boro-silicate glass (BS), while less expansion was recorded in mixes with green glass (GG). As compared to reference mix (FC), it was noted that the mixes with crushed waste glass (SL), (BS), and (CR) undergo notable expansion, while the expansion of the mixes with (GG) slightly increased compared to the reference mix (FC).

Development of soapstock processing technology to ensure waste-free and safe production

Soapstock is a large-tonnage waste of the oil and fat industry, the disposal of which is environmentally hazardous. Processing of soapstock into industrially valuable products, in particular, fatty acids, is promising. The method for producing fatty acids, which consists in sequential saponification of soapstock with sodium hydroxide solution, salting out with sodium chloride and decomposition with sulfuric acid solution has been investigated. The feature of this work is the study of the effect of salting out conditions of saponified soapstock on the yield and neutralization number of fatty acids. As an experimental sample, sunflower soapstock was used, the indicators of which correspond to DSTU 5033 (CAS 68952-95-4): mass fraction of total fat – 67.3 %, fatty acids – 61.8 %, neutral fat – 5.5 %. Soapstock was subjected to preliminary saponification under the following conditions: duration 85 min., concentration of sodium hydroxide solution 45 %. After that, the saponified mass was subjected to salting out. The obtained core soap was decomposed with the sulfuric acid solution under the following conditions: temperature 90 °C, duration 40 min. Rational salting out conditions were determined: duration (80 min.) and sodium chloride concentration (16%). Under these conditions, the fatty acid yield is 95.0 %, the neutralization number is 194.8 mg KOH/g. The resulting fatty acids comply with DSTU 4860 (CAS 61788-66-7): the mass fraction of moisture and volatiles is 0.85 %, the mass fraction of total fat is 98.9 %, cleavage depth is 94.2 % oleic acid. This method of soapstock processing increases the fatty acid yield by 3.5 % compared to the method with saponification and decomposition, by 20.3 % compared to the method of soapstock decomposition with sulfuric acid. At the same time, the neutralization number increases by 4.1 % and 8.2 %, respectively. The improved method for fatty acids producing from soapstock provides high- quality fatty acids with increased yield.

Statistical Analysis of SO2 and NO2 with Respect to Meteorological Parameters (Gwalior, India)

The present study is carried out in Gwalior to know the level of pollutants viz sulphur dioxide (SO2) and nitrogen dioxide (NO2). In this study, both NO2 and SO2 were collected during different seasons, and estimation was done using chemical methods. The methods used for the determination of SO2 and NO2 in the ambient air of Gwalior was (Modified West and Geake method) and (Modified Jacob and Hochheisier). The SO2 from the air stream was absorbed in a sodium tetramer curate solution. NO2 was collected by bubbling air through a sodium hydroxide solution to form a stable solution of sodium nitrate. Meteorological parameters like temperature, relative humidity were recorded by thermometers and hygrometry during the sampling. Rainfall data was taken from Indian Meteorological Department, New Delhi, for four sampling years. The statistical analysis was carried out between the level of pollutants SO2 and NO2 measured and meteorological parameters recorded during the sampling. This study observed that pollutants were very high in winter and summer compared to monsoon and post-monsoon periods due to the heavy transport movement and favourable meteorological conditions like temperature, humidity, rainfall, and wind speed and directions.

Effect of Curing Temperature on the Mechanical Strength of Alkali Activated Laterite Geopolymeric Samples

A huge amount of carbon dioxide is released in the Portland cement production process. A large quantity of greenhouse gases is produced because of the significant amount of energy consumption via making bricks through firing. Using the pozzolanic sources containing the aluminosilicate and alkaline reagents, a new type of green materials called geopolymeric materials are produced with quite lower environmental hazards. The use of laterite as an iron-rich aluminosilicate material has a high potential for building materials. In this study, the effect of the curing temperature and characteristics of the alkaline reagent including the concentration of sodium hydroxide solution and the water-glass to sodium hydroxide mass mixing ratio on the mechanical strength of the laterite-based, oven-cured geopolymer samples was investigated. The results showed that the curing temperature had a significant effect on the compressive strength of the laterite-based geopolymer samples so that with a 15°C change at the curing temperature, the compressive strength of the samples could be multiplied and a sharp increase in the mechanical strength could occur. Also, according to the results of this study, the 6 M sodium hydroxide is recommended for the construction of the laterite-based geopolymer materials with low cost and relatively high strength, and for the construction of higher-strength building materials, the 14 M sodium hydroxide is recommended.

Effect of water and alkali on purification bacterial cellulose membrane from Kombucha

Bacterial cellulose membrane (BCM) is a biomaterial synthesized by bacteria of the genus Gluconocetobacter hansenii with a higher degree of purity than plant cellulose. The commonly used raw material for manipulating bacterial cellulose is kombucha, a beverage consumed by a vast population around the world that promises health benefits. The beverage is composed of tea species Camellia sinenses and a carbon source, refined sucrose, and a starter culture of bacteria and yeast with 10% fermented tea (starter tea) to activate the fermentative process. The Kombucha’s bacterial cellulose membranes (KBCM) are formed over 7 to 10 days on the surface of the fermented product and have the appearance of a gelatinous membrane, this being the by-product of interest. In this work, the objective was to obtain the membrane composed of cellulose via Kombucha and purify it to obtain crystalline cellulose. The purification was performed with distilled water and 0.5M NaOH sodium hydroxide solution to remove residues from the fermentation, successfully removing sugars and bacteria. At the end of the experiments, a lighter film was obtained with coloration close to white, and comparative analyses were performed to verify the structural chemical composition, crystallinity, and morphology of the samples by techniques FTIR, DRX, and SEM, respectively. Then, once the biomaterial was purified, the range of applications expanded to several products to meet the biomedical area, sustainable packaging, and even the fashion industry.

Obtaining Nickel Concentrates from Sludge Produced in the Process of Electrochemical Metal Surface Treatment

The article presents the possibility of recovering nickel from waste produced as a result of wastewater neutralization during the electrochemical surface treatment of metals. Leaching the sludge with concentrated hydrochloric acid enabled the metals contained in the sludge from precipitate to the solution with the efficiency of 74.4% (Se) to 100% (Zn). The content of elements was determined using the ICP-OES method. The next step was the precipitation of metals from the obtained solution using various reagents. The precipitating reagents used were 0.5 M sodium hydroxide solution, 0.5 M sodium sulphide solution and 1% dimethylglyoxime solution. Selective precipitation made it possible to obtain nickel concentrates with the content of nickel ranging from 15.3 to 98.2% for the first two methods, whereas in the case of the third method based on a dimethylglyoxime solution, the obtained nickel concentrate purity was 94.3%. The process of leaching nickel-dimethylglyoxime complex (Ni-DMG) with sulphuric acid and crystallization enabled obtaining 99.4% purity nickel sulphate, which can be reused in the nickel plating of selected metals. The research shows that waste generated in the process of neutralization of wastewater from electroplating plants is a potentially important source of recycled nickel concentrates.

Influence of NaOH treatment of rubber aggregates on the durability properties of rubberized mortars

The work presented in this paper aims to study the durability of mortars, in which part of the sand has been replaced with rubber aggregates from used tires and have undergone a surface treatment with a sodium hydroxide solution (NaOH). The substitution rates studied are 10%, 17.5%, and 25%. The results are compared with ordinary mortar and mortars with untreated rubber aggregates while samples with the same substitution rates were used. To do this, the following properties have been studied: compressive strength, flexural tensile strength, water absorption by capillarity, water absorption by total immersion, water-accessible porosity, water permeability, and resistance to the chemical degradation by sulfuric acid H2SO4. The results obtained show that the treatment of rubber aggregates by the solution method (NaOH) presented a considerable improvement in mechanical performance (increase in compressive strength and flexural tensile strength) and better durability compared to reference mortar and mortar with untreated rubber granulate.

Live-Scale Testing of Granular Materials Stabilized with Alkali-Activated Waste Glass and Carbide Lime

The increasingly strong search for alternative materials to Portland cement has resulted in the development of alkali-activated cements (AAC) that are very effective at using industrial by-products as raw materials, which also contributes to the volume reduction in landfilled waste. Several studies targeting the development of AAC—based on wastes containing silicon and calcium—for chemical stabilization of soils have demonstrated their excellent performance in terms of durability and mechanical performance. However, most of these studies are confined to a laboratory characterization, ignoring the influence and viability of the in situ construction process and, also important, of the in situ curing conditions. The present work investigated the field application of an AAC based on carbide lime and glass wastes to stabilize fine sand acting as a superficial foundation. The assessment was supported on the unconfined compressive strength (UCS) and initial shear modulus (G0) of the developed material, and the field results were compared with those prepared in the laboratory, up to 120 days curing. In situ tests were also developed on the field layers (with diameters of 450 and 900 mm and thickness of 300 mm) after different curing times. To establish a reference, the mentioned precursors were either activated with a sodium hydroxide solution or hydrated with water (given the reactivity of the lime). The results showed that the AAC-based mixtures developed greater strength and stiffness at a faster rate than the water-based mixtures. Specimens cured under controlled laboratory conditions showed better results than the samples collected in the field. The inclusion of the stabilized layers clearly increased the load-bearing capacity of the natural soil, while the different diameters produced different failure mechanisms, similar to those found in Portland cement stabilization.

Heterotrophically Ultrahigh-Cell-Density Cultivation of a High Protein-Yielding Unicellular Alga Chlorella With a Novel Nitrogen-Supply Strategy

The unicellular green alga Chlorella is an ideal protein source. However, the high production cost and low production capability of the current main photoautotrophic culture mode limit its application especially as an alternative protein source for food and feed, which might be overcome through high-cell-density cultivation in fermenters. In this study, a Chlorella sorokiniana strain CMBB276 with high protein content was selected from five Chlorella strains by comprehensive evaluation of their growth rates, protein contents, and yields. The optimal cultural temperature, pH, and mole ratio of carbon and nitrogen (C/N) for C. sorokiniana CMBB276 growth were found to be 30°C, 6.5, and 18, respectively. Ammonium chloride was proved to be the best nitrogen (N) source for C. sorokiniana CMBB276 growth, whereas growth inhibition caused by the accumulation of salts was observed under fed-batch cultivation when maintaining a constant C/N ratio of 18 by controlling pH with sodium hydroxide solution. By simultaneously reducing the concentration of ammonium chloride in the feeding medium and controlling pH with ammonium hydroxide, we finally achieved the ultrahigh-cell-density cultivation of C. sorokiniana CMBB276. The highest biomass concentration and protein yield reached 232 and 86.55 g l−1, respectively, showing the great potential of culturing C. sorokiniana CMBB276 in fermenters for economic and large-scale protein source production.

Silica removal from waste of ilmenite concentrate pyrometallurgical processing

The article presents the study results for alkaline leaching of fine ilmenite concentrate dusts from electric smelting. The physical and chemical properties of the dusts were studied using chemical and instrumental analysis methods. The dust composition was determined, X-ray phase analysis showed that the dust sample substance is in the X-ray amorphous state, iron is present in the trivalent state, and silicon is bound to magnesium. The dust sample study using a scanning electron microscope showed that part of the titanium is bound in a hard-to-disclose anasovite encapsulated in amorphous silicon oxide. The leaching study of electric smelting dust with sodium hydroxide solutions included the study of the effect of sodium hydroxide concentration, process duration, temperature, S: L ratio. The optimal conditions for dust leaching from electric smelting of ilmenite concentrate have been established: temperature 80-90 °C, duration 90-120 min, ratio S: L = 1: 5, the concentration of sodium hydroxide solution 110-115 g/dm3. The silicon extraction degree into the solution under these conditions was 77.7%. The behavior of accompanying components of chromium, zinc, iron, and manganese during dust leaching was also studied. X-ray phase analysis of the cake after leaching shows almost complete amorphization of the leached product, the main phase is a solid solution of Fe2O3·TiO2.