Research on Mechanical Response of Pavement Structure to Differential Settlement of Subgrade on Highway Widening

Based on the widening project of Ri-Lan highway in China, the finite element model is established by PLAXIS. By applying differential settlement at the bottom of the pavement, the mechanical response of the pavement structure is analysed. Finally, the differential settlement control standard indicated by crack strength is proposed. The results show that, under the effect of differential settlement, within about 4 cm of old pavement surface and upper base bear tensile stress, the base first reaches the failure strength. Under 4 cm of the old pavement surface, the subbase first reaches the failure strength. The differential settlement control standard of the pavement structure is determined by the splitting strength of the material, and we, respectively, control the differential settlement of less than 23.4 mm, where the corresponding cross-slope rate is 0.33%, and below 75.2 mm, where the corresponding cross-slope rate is 0.54%. It could support practical engineering applications.

Effect of Geo-Grid Depth in Roads Cross-Section on Reducing Pavement Rutting

Pavement structures cover vast areas of urban cities and non-urban roads and play a key role in daily commuting functionality and economic development; therefore, they must be conserved against any distress. The rutting problem, being a major distress to the pavement structure, must be solved and dealt with in order to preserve its value. One way of solving this dilemma is by using geo-grids within the pavement structure. A geo-grid is a synthetic material usually made from polymers with different thicknesses and stiffnesses. This paper investigates the effects of geo-grids on reducing the rutting occurrence through adding a layer of geo-grid with certain properties at different levels of the pavement structure. We also investigate, the result of the added geo-grid material to the developed vertical stresses within the pavement cross-section. This investigation is conducted by constructing a 3-D finite elements-based (FE) model of a pavement cross-section using ANSYS software; student version R1 2021. The FE-based model is validated by comparing its numerical predictions with the experimental results acquired from an accelerated large-scale paved model. The results show that the deeper the geo-grid is positioned, the more significant the rutting resistance is observed due to the stiffness of the geo-grid bearing the tensile force until a certain depth. Moreover, noticeable stress reduction is seen in the developed vertical compressive stresses below the loading area resisted by the geo-grid.

Study on the Influence and Law of Waterproof System Design Factors on the Typical Stress of Bridge Deck Pavement

To improve the structural design rationality of cement concrete bridge deck pavement systems and reduce diseases such as interlayer displacement and rutting in the early stage of bridge deck use, this paper studies the influence and law of the coupling effect of various factors of the waterproof system on the typical stress of bridge deck pavement and determines the best structure combination for the bridge deck pavement structure. A finite element model was established by using commercial software to simulate the mechanical response of different types of waterproof bonding layer, waterproof leveling layer, and impervious structure layer under different parameters. The simulation results show that when the thickness of the pavement layer was 8 cm, the maximum shear stress of the pavement layer occurred in the middle of the wearing course and the junction between layers. When the pavement layers were continuous, the maximum strain of the waterproof bonding layer with the “rubber asphalt + protective plate” structure in the transverse and longitudinal directions was the largest. When the waterproof leveling layer was cement concrete, the structure bore a large amount of stress and easily produced cracks, resulting in water damage. High-density water-based asphalt concrete with a low permeability coefficient can reduce the interlayer shear stress and effectively ensure the interlayer bonding effect. On this basis, the following bridge deck pavement structure was proposed: waterproof system + multifunctional waterproof layer + load-bearing structure layer + surface functional layer.

Full-Scale Experimental Evaluation of the Flood Resiliency of Thin Concrete Overlay on Asphalt Pavements

The capacity to resist flooding is one of the critical challenges of pavement resiliency in locations subject to inundation. Flooding increases moisture contents, which weakens most pavement materials. Although the effect of moisture on the mechanical properties of most pavement materials is reversible, the structural damage caused by trafficking applied on the weakened pavement structure is not. The critical time for structural damage is typically after the flood and before “life-line” pavements have dried back when trucks are bringing in relief supplies and hauling out demolition. This fact, together with the increased occurrence of extreme weather events and sea level rise resulting from climate change, emphasizes the need to better understand the impacts of flooding on identified life-line pavements. This paper evaluates the flooding resiliency of thin concrete overlay on asphalt (COA) pavements by studying the effects that water saturation produces on the pavement structure. The research is based on the structural response and distresses measured in five thin COA sections that were instrumented with sensors and tested with a heavy vehicle simulator (HVS) under flooded conditions. The research shows that the flooding did not produce a noticeable change in the structural capacity of the COA, based on the structural response measured under the loading of the HVS wheel and the falling weight deflectometer, but did result in some structural damage to the asphalt base in some of the sections.