Properties of Investment Cast RS5 Heat Treated in an Optimised Four Step Route

Author(s):  
Wei Li ◽  
Paul Andrews
Keyword(s):  
Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4452
Author(s):  
Łukasz Rakoczy ◽  
Bogdan Rutkowski ◽  
Małgorzata Grudzień-Rakoczy ◽  
Rafał Cygan ◽  
Wiktoria Ratuszek ◽  
...  

The microstructure of a René 108 Ni-based superalloy was systematically investigated by X-ray diffraction, light microscopy, energy-dispersive X-ray spectroscopy, and electron microscopy techniques. The material was investment cast in a vacuum and then solution treated (1200 °C-2h) and aged (900 °C-8h). The γ matrix is mainly strengthened by the ordered L12 γ′ phase, with the mean γ/γ′ misfit, δ, +0.6%. The typical dendritic microstructure with considerable microsegregation of the alloying elements is revealed. Dendritic regions consist of secondary and tertiary γ′ precipitates. At the interface of the matrix with secondary γ′ precipitates, nano M5B3 borides are present. In the interdendritic spaces additionally primary γ′ precipitates, MC and nano M23C6 carbides were detected. The γ′ precipitates are enriched in Al, Ta, Ti, and Hf, while channels of the matrix in Cr and Co. The highest summary concentration of γ′-formers occurs in coarse γ′ surrounding MC carbides. Borides M5B3 contain mostly W, Cr and Mo. All of MC carbides are enriched strongly in Hf and Ta, with the concentration relationship between these and other strong carbide formers depending on the precipitate’s morphology. The nano M23C6 carbides enriched in Cr have been formed as a consequence of phase transformation MC + γ → M23C6 + γ′ during the ageing treatment.


Author(s):  
Thomas R. McKee ◽  
Peter R. Buseck

Sediments commonly contain organic material which appears as refractory carbonaceous material in metamorphosed sedimentary rocks. Grew and others have shown that relative carbon content, crystallite size, X-ray crystallinity and development of well-ordered graphite crystal structure of the carbonaceous material increases with increasing metamorphic grade. The graphitization process is irreversible and appears to be continous from the amorphous to the completely graphitized stage. The most dramatic chemical and crystallographic changes take place within the chlorite metamorphic zone.The detailed X-ray investigation of crystallite size and crystalline ordering is complex and can best be investigated by other means such as high resolution transmission electron microscopy (HRTEM). The natural graphitization series is similar to that for heat-treated commercial carbon blacks, which have been successfully studied by HRTEM (Ban and others).


Author(s):  
K. P. Staudhammer ◽  
L. E. Murr

The effect of shock loading on a variety of steels has been reviewed recently by Leslie. It is generally observed that significant changes in microstructure and microhardness are produced by explosive shock deformation. While the effect of shock loading on austenitic, ferritic, martensitic, and pearlitic structures has been investigated, there have been no systematic studies of the shock-loading of microduplex structures.In the current investigation, the shock-loading response of millrolled and heat-treated Uniloy 326 (thickness 60 mil) having a residual grain size of 1 to 2μ before shock loading was studied. Uniloy 326 is a two phase (microduplex) alloy consisting of 30% austenite (γ) in a ferrite (α) matrix; with the composition.3% Ti, 1% Mn, .6% Si,.05% C, 6% Ni, 26% Cr, balance Fe.


Author(s):  
Shiro Fujishiro

The Ti-6 wt.% Al-4 wt.% V commercial alloys have exhibited an improved formability at cryogenic temperature when the alloys were heat-treated prior to the tests. The author was interested in further investigating this unusual ductile behavior which may be associated with the strain-induced transformation or twinning of the a phase, enhanced at lower temperatures. The starting materials, supplied by RMI Co., Niles, Ohio were rolled mill products in the form of 40 mil sheets. The microstructure of the as-received materials contained mainly ellipsoidal α grains measuring between 1 and 5μ. The β phase formed an undefined grain boundary around the a grains. The specimens were homogenized at 1050°C for one hour, followed by aging at 500°C for two hours, and then quenched in water to produce the α/β mixed microstructure.


Author(s):  
W. T. Donlon ◽  
S. Shinozaki ◽  
E. M. Logothetis ◽  
W. Kaizer

Since point defects have a limited solubility in the rutile (TiO2) lattice, small deviations from stoichiometry are known to produce crystallographic shear (CS) planes which accomodate local variations in composition. The material used in this study was porous polycrystalline TiO2 (60% dense), in the form of 3mm. diameter disks, 1mm thick. Samples were mechanically polished, ion-milled by conventional techniques, and initially examined with the use of a Siemens EM102. The electron transparent thin foils were then heat-treated under controlled atmospheres of CO/CO2 and H2 and reexamined in the same manner.The “as-received” material contained mostly TiO2 grains (∼5μm diameter) which had no extended defects. Several grains however, aid exhibit a structure similar to micro-twinned grains observed in reduced rutile. Lattice fringe images (Fig. 1) of these grains reveal that the adjoining layers are not simply twin related variants of a single TinO2n-1 compound. Rather these layers (100 - 250 Å wide) are alternately comprised of stoichiometric TiO2 (rutile) and reduced TiO2 in the form of Ti8O15, with the Ti8O15 layers on either side of the TiO2 being twin related.


Author(s):  
L. S. Lin ◽  
K. P. Gumz ◽  
A. V. Karg ◽  
C. C. Law

Carbon and temperature effects on carbide formation in the carburized zone of M50NiL are of great importance because they can be used to control surface properties of bearings. A series of homogeneous alloys (with M50NiL as base composition) containing various levels of carbon in the range of 0.15% to 1.5% (in wt.%) and heat treated at temperatures between 650°C to 1100°C were selected for characterizations. Eleven samples were chosen for carbide characterization and chemical analysis and their identifications are listed in Table 1.Five different carbides consisting of M6C, M2C, M7C3 and M23C6 were found in all eleven samples examined as shown in Table 1. M6C carbides (with least carbon) were found to be the major carbide in low carbon alloys (<0.3% C) and their amounts decreased as the carbon content increased. In sample C (0.3% C), most particles (95%) encountered were M6C carbide with a particle sizes range between 0.05 to 0.25 um. The M6C carbide are enriched in both Mo and Fe and have a fee structure with lattice parameter a=1.105 nm (Figure 1).


Sign in / Sign up

Export Citation Format

Share Document