Validation of a Terminally Amino Functionalized Tetra‐Alkyl Sn(IV) Precursor in Metal–Organic Chemical Vapor Deposition of SnO 2 Thin Films: Study of Film Growth Characteristics, Optical, and Electrical Properties

2018 ◽  
Vol 6 (1) ◽  
pp. 1801540 ◽  
Author(s):  
David Zanders ◽  
Engin Ciftyurek ◽  
Christian Hoppe ◽  
Teresa de los Arcos ◽  
Aleksander Kostka ◽  
...  
1997 ◽  
Vol 12 (5) ◽  
pp. 1214-1236 ◽  
Author(s):  
Bruce J. Hinds ◽  
Richard J. McNeely ◽  
Daniel B. Studebaker ◽  
Tobin J. Marks ◽  
Timothy P. Hogan ◽  
...  

Epitaxial Tl2Ba2CaCu2O8 thin films with excellent electrical transport characteristics are grown in a two-step process involving metal-organic chemical vapor deposition (MOCVD) of a BaCaCuO(F) thin film followed by a postanneal in the presence of Tl2O vapor. Vapor pressure characteristics of the recently developed liquid metal-organic precursors Ba(hfa)2 • mep (hfa = hexafluoroacetylacetonate, mep = methylethylpentaglyme), Ca(hfa)2 • tet (tet = tetraglyme), and the solid precursor Cu(dpm)2 (dpm = dipivaloylmethanate) are characterized by low pressure thermogravimetric analysis. Under typical film growth conditions, transport is shown to be diffusion limited. The transport rate of Ba(hfa)2 • mep is demonstrated to be stable for over 85 h at typical MOCVD temperatures (120 °C). In contrast, the vapor pressure stability of the commonly used Ba precursor, Ba(dpm)2, deteriorates rapidly at typical growth temperatures, and the decrease in vapor pressure is approximately exponential with a half-life of ∼9.4 h. These precursors are employed in a low pressure (5 Torr) horizontal, hot-wall, film growth reactor for growth of BaCaCuO(F) thin films on (110) LaAlO3 substrates. From the dependence of film deposition rate on substrate temperature and precursor partial pressure, the kinetics of deposition are shown to be mass-transport limited over the temperature range 350–650 °C at a 20 nm/min deposition rate. A ligand exchange process which yields volatile Cu(hfa)2 and Cu(hfa) (dpm) is also observed under film growth conditions. The MOCVD-derived BaCaCuO(F) films are postannealed in the presence of bulk Tl2Ba2CaCu2O8 at temperatures of 720–890 °C in flowing atmospheres ranging from 0–100% O2. The resulting Tl2Ba2CaCu2O8 films are shown to be epitaxial by x-ray diffraction and transmission electron microscopic (TEM) analysis with the c-axis normal to the substrate surface, with in-plane alignment, and with abrupt film-substrate interfaces. The best films exhibit a Tc = 105 K, transport-measured Jc= 1.2 × 105 A/cm2 at 77 K, and surface resistances as low as 0.4 mΩ (40 K, 10 GHz).


1997 ◽  
Vol 12 (6) ◽  
pp. 1655-1660 ◽  
Author(s):  
Daisuk Nagano ◽  
Hiroshi Funakubo ◽  
Osamu Sakurai ◽  
Kazuo Shinozaki ◽  
Nobuyasu Mizutani

Insulating epitaxially grown SrTiO3 thin films were prepared on (100)MgO substrates by metal-organic chemical vapor deposition (MOCVD). Semiconductive SrTiO3 thin films were obtained by the rapid cooling after reheating in reduction atmosphere. The microstructure, crystal structure, and electrical properties of these films were investigated. The electrical properties varied by the composition of films and heat-treatment conditions, i.e., the heating temperature, the oxygen partial pressure, and the cooling rate after the annealing. Change of the resistivity of the film was attributed to that of the carrier concentration. Mobility of films was unchanged, and the value was almost the same order of that of bulks. The lowest resistivity of 0.1 Ω·cm was obtained when a sample of Ti/Sr = 1.0 was heated at 1200 °C under 10−15 Pa of PO2 and then rapidly cooled. This value is similar to that of bulks (100 –10−1 Ω · cm).


2004 ◽  
Vol 449-452 ◽  
pp. 997-1000 ◽  
Author(s):  
Gwang Pyo Choi ◽  
Yong Joo Park ◽  
Whyo Sup Noh ◽  
Jin Seong Park

Tin oxide thin films were deposited at 375 °C on α-alumina substrate by metal-organic chemical vapor deposition (MOCVD) process. A number of hillocks on the film were formed after air annealing at 500 °C for 30 min and few things in N2 annealing. The oxygen content and the binding energy after air annealing came to close the stoichiometric SnO2. The cauliflower hillocks of the film seem to be formed by the continuous migration of crystallites from a cauliflower grain on the substrate to release the stress due to the increase of oxygen content and volume.


Sign in / Sign up

Export Citation Format

Share Document