Hydrodynamics of gas-liquid flow in micropacked beds: Pressure drop, liquid holdup, and two-phase model

AIChE Journal ◽  
2017 ◽  
Vol 63 (10) ◽  
pp. 4694-4704 ◽  
Author(s):  
Jisong Zhang ◽  
Andrew R. Teixeira ◽  
Lars Thilo Kögl ◽  
Lu Yang ◽  
Klavs F. Jensen
Keyword(s):  
Pressure Drop ◽  
Liquid Flow ◽  
Phase Model ◽  
Liquid Holdup ◽  
Two Phase ◽  
Gas Liquid Flow

The effect of two-phase flow regime on hydrodynamics and mass transfer in a horizontal-tube gas-liquid reactor

1985 ◽  
Vol 50 (3) ◽  
pp. 745-757 ◽  
Author(s):  
Andreas Zahn ◽  
Lothar Ebner ◽  
Kurt Winkler ◽  
Jan Kratochvíl ◽  
Jindřich Zahradník
Keyword(s):  
Mass Transfer ◽  
Pressure Drop ◽  
Flow Regime ◽  
Liquid Flow ◽  
Horizontal Tube ◽  
Liquid Holdup ◽  
Two Phase ◽  
Flow Rates ◽  
Type Relation ◽  
Good Agreement

The effect of two-phase flow regime on decisive hydrodynamic and mass transfer characteristics of horizontal-tube gas-liquid reactors (pressure drop, liquid holdup, kLaL) was determined in a cocurrent-flow experimental unit of the length 4.15 m and diameter 0.05 m with air-water system. An adjustable-height weir was installed in the separation chamber at the reactor outlet to simulate the effect of internal baffles on reactor hydrodynamics. Flow regime maps were developed in the whole range of experimental gas and liquid flow rates both for the weirless arrangement and for the weir height 0.05 m, the former being in good agreement with flow-pattern boundaries presented by Mandhane. In the whole range of experi-mental conditions pressure drop data could be well correlated as a function of gas and liquid flow rates by an empirical exponential-type relation with specific sets of coefficients obtained for individual flow regimes from experimental data. Good agreement was observed between values of pressure drop obtained for weirless arrangement and data calculated from the Lockhart-Martinelli correlation while the contribution of weir to the overall pressure drop was well described by a relation proposed for the pressure loss in closed-end tubes. In the region of negligible weir influence values of liquid holdup were again succesfully correlated by the Lockhart-Martinelli relation while the dependence of liquid holdup data on gas and liquid flow rates obtained under conditions of significant weir effect (i.e. at low flow rates of both phases) could be well described by an empirical exponential-type relation. Results of preliminary kLaL measurements confirmed the decisive effect of the rate of energy dissipation on the intensity of interfacial mass transfer in gas-liquid dispersions.

scholarly journals Pressure Drops in Two-Phase Gas–Liquid Flow through Channels Filled with Open-Cell Metal Foams

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2419
Author(s):  
Roman Dyga ◽  
Sebastian Brol
Keyword(s):  
Pressure Drop ◽  
Liquid Flow ◽  
Single Phase ◽  
Fluid Pressure ◽  
Metal Foams ◽  
Geometrical Parameters ◽  
Two Phase ◽  
Pressure Drops ◽  
Flow Through ◽  
Gas Liquid Flow

This paper describes experimental investigations of single-phase and two-phase gas–liquid flow through channels with a diameter of 20 mm and length of 2690 mm, filled with metal foams. Three types of aluminium foams with pore densities of 20, 30 and 40 PPI and porosities ranging from 29.9% to 94.3% were used. Air, water and oil were pumped through the foams. The tests covered laminar, transitional and turbulent flow. We demonstrated that the Reynolds number, in which the hydraulic dimension should be defined based on foam porosity and pore diameter de = ϕdp/(1 − ϕ), can be used as a flow regime assessment criterion. It has been found that fluid pressure drops when flowing through metal foams significantly depends on the cell size and porosity of the foam, as well as the shape of the foam skeleton. The flow patterns had a significant influence on the pressure drop. Among other things, we observed a smaller pressure drop when plug flow changed to stratified flow. We developed a model to describe pressure drop in flow through metal foams. As per the proposed methodology, pressure drop in single-phase flow should be determined based on the friction factor, taking into account the geometrical parameters of the foams. We propose to calculate pressure drop in gas–liquid flow as the sum of pressure drops in gas and liquid pressure drop corrected by the drop amplification factor.

Pressure drop in two phase gas-liquid flow in inclined pipes

1982 ◽  
Vol 8 (4) ◽  
pp. 407-431 ◽  
Author(s):  
P.L. Spedding ◽  
J.J.J. Chen ◽  
Van Thanh Nguyen
Keyword(s):  
Pressure Drop ◽  
Liquid Flow ◽  
Two Phase ◽  
Gas Liquid Flow ◽  
Inclined Pipes
Sign in / Sign up

Export Citation Format

Share Document